LED Studio 3203D/3203T
PR-3203T
PR-3203D
This product manual contains important information about the safe installation and use of this unit.
Please read and follow these instructions carefully and keep this manual in a safe place for future
reference.
PR LIGHTING LTD.
http://www.pr-lighting.com
2 / 12
INDEX
ACESSORIES ......................................................................................................................................................... 2
SAFE USAGE OF THE UNIT .................................................................................................................................... 3
INSTALLING THE UNIT .......................................................................................................................................... 4
CONTROL CONNECTION ...................................................................................................................................... 4
DMX TERMINATOR ............................................................................................................................................. 5
OPERATION MENU ............................................................................................................................................................. 6
DMX PROTOCOL ................................................................................................................................................................. 6
INDICATION OF LED DIGITAL TUBE ................................................................................................................................... 6
SETUP OPTIONS-UNIT CONFIGURATION .......................................................................................................................... 7
MAINTENANCE ................................................................................................................................................................... 8
TROUBLESHOOTING ........................................................................................................................................................ 8
TECHNICAL DATA ............................................................................................................................................................ 9
ELECTRICAL DIAGRAM ............................................................................................................................................... 11
COMPONENT ORDER CODES ...................................................................................................................................... 11
BACK COVER ................................................................................................................................................................. 12
Please note that as part of our ongoing commitment to continuous product development, specifications are
subject to change without notice. Whilst every care is taken in the preparation of this manual we reserve the
right to change specifications in the course of product improvement. The publishers cannot be held responsible
for the accuracy of the information herein, or any consequence arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and /
or the unit are in good condition before installation and use. Should there be any damage caused by
transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be
assumed by the manufacturer and / or dealer.
ACCESSORIES
These items are packed together with the unit:
Name
Quantity
Unit
Remark
Safety cord
2
Pc
With one 1.2m and the other 0.55m in length
XLR signal cable
1
Pc
Power cord
1
Pc
User’s manual
1
Pc
Clamp and Mounting Bolt
1
Set
3 / 12
SAFE USAGE OF THE UNIT
When unpacking and before disposing of the carton, check there is no transportation damage before using the unit. Should
there be any damage caused by transportation, consult your dealer and do not use the apparatus.
The unit can be only used indoors, IP20. The fixture should be kept in dry place without excessive dampness, heat, dust and
contact with water or other liquids.
The unit is not designed or intended to be mounted directly on to inflammable surfaces.
The unit is only intended for installation, operation and maintenance by qualified personnel.
Do not project the beam onto inflammable surfaces, minimum distance is 2m. 2m
Avoid direct exposure to the light from the lamp. The light is harmful to eyes.
Do not attempt to dismantle and/or modify the unit in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power requirements of the unit.
It is essential that each unit is correctly earthed and that electrical installation conforms to all relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact with other
cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.
When the unit is hanged to a high place, please use a safety cord provided to pass through the unit’s support as a secondary
safety fixing for safety seasons. For details, refer to “INSTALL THE UNIT “section.
Exterior surface temperatures of the unit after 5 minutes’ operation is 45℃, when achieving steady state it is 55℃.
There is no user serviceable parts inside the unit, do not open the housing and never operate the unit with the covers removed.
If any questions, don’t hesitate to consult your dealer or manufacturer.
Always disconnection from the power, when the device is not in use or before cleaning or any
maintenance work !
4 / 12
INSTALL THE UNIT
The figures above with a Mounting Bar for the illustrations of the installation is for our clients’ reference and it
is not a accessory to be supplied up on delivery . This fixture should be hung upon use, but not hung by its side.
The whole fixture can be rotated by hand within the range of 180 degrees. While installation, take out two
safety cords supplied and hook the clamp to the fixture’s support, then hook the clamp to the Mounting Bar and
tighten the fasteners of the clamp to mount the whole fixture. Please be sure that the fixture is mounted
securely and the mounting place strong enough to support the fixture’s weight. For safety, please run a 1.2m
safety cord supplied through the Mounting Bar and the Mounting Structure of the fixture, and a second 0.55m
safety cord though the barn door module as the figures above for the supplement to ensure safety.
Warning:
1. The unit MUST be lifted or carried via supporting frame instead of clamps.
2. For safety the long safety cord should afford 10 times the unit’s weight and the short one 10 times barn door
module’s weight.
CONTROL CONNECTION
5 / 12
Connection between the controller and a unit and between one unit and another must be made with a 2 core-screened cable,
with each core having at least a 0.5mm diameter. Please use the unit’s cannon 5- pin signal input and output cables as
connection. The 5-pin signal connections are connected as shown in the figure above.
Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the
plug is not connected in any way. The unit accepts digital control signals in protocol DMX512 (1990).
The maximum of units in parallel for operation is 16 pcs. Connect the controller’s output to the first fixture’s input, and
connect the first fixture’s output to the second fixture’s input and connect the rest fixtures in the same way. Eventually connect
the last fixture’s output to a DMX terminator as shown in the figure below. Note: for synchronous control, the start addresses
of all slaves should be same.
Each unit should be connected to power supply individually and the voltage and frequency of the power supply should match
those indicated on nameplate.
DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This
prevents electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120 (ohm) resistor connected across pins 2 and 3, which is then
plugged into the output socket on the last unit in the chain. The connections are illustrated below.
6 / 12
Operations Menu
1st level menu
2nd level menu
3rd level menu
Remarks
DMX Address
001 - 512
Setup of DMX Address
Config Setup
LED Dimmer Test
Reference Only, not saved
Focus Position
Linearly focusing
Lcd Light Setup
On
ON
Off
Display shuts off 3 minutes after
buttons are not pressed after the exit
of menus
Language Setup
English
Language selection
Chinese
Display Inversion
On
Display Inversion
Off
Information
LED Temperature
XXXX
Fixture use Time
V.X.X
Fixture usage time
Software Version
V.X.X
DMX PROTOCOL
CHANNEL
FUNCTION
DMX
DESCRIPTION
1
Dimmer
000-255
From dark to bright
2
Strobe
000 - 007
NO strobe
008 - 255
Strobe speed from slow to fast
3
Focusing
000-255
From small angle to big angle
INDICATION OF LED DIGITAL TUBE
ADD Indication
ON
DMX signal
OFF
NO DMX signal
7 / 12
SETUP OPTIONS-UNIT CONFIGURATION
DMX
Explanations for Control Panel and Potentiometer
After power-on, LCD display displays the company’s LOGO “PR”. After reset, the display is at initial display status
showing information about company’s name including LOGO “PR”, fixture’s model and DMX address( if the start address
is 001, it displays as “address=001”) and at the same time the display is locked.
To browse through or change a fixture’s configuration, after ENTER button has been pressed for about 3 seconds, the display
of AddR means the entrance of the menu. To set or browse through a fixture’s settings, press buttons of UP and DOWN.
After button ENTER is pressed, a sub-menu is entered showing current parameters while parameters flashing. Press button
UP or DOWN to change values(plus or minus)
Press button ENTER to save your settings or enter into the upper level menu and the parameters stops from flashing.
Press FUNC to enter into the upper level menu(parameters not saved )or browse through the upper level menu.
After FUNC is pressed for more than 1second or buttons not pressed for more than 1 minute, it will go back to LCD display
initial stage.
After the exit of the menus, the fixture’s brightness can be adjusted by potentiometer.( Only after the exit of the menus and no
DMX signal can this work)
If there is DMX signal, the DMX signal indication will be on, and at the same time LCD display displays DMX address
accordingly, otherwise, the indication will be off..
After the startup of the fixture, reset begins, but the lamp will be on after the reset is completed, at this stage, the brightness of
the fixture is as what the potentiometer points to. If the brightness needs to be changed, please follow the above-mentioned
instructions. After reset, the focal length will be the one set during last use..
Operation Guide
1. Setup of Start Address
Each unit must be given a DMX start address so that the correct unit responds to the correct control signals. This DMX start
address is the channel number from which the unit starts to “listen” to the digital control information being sent out from the
controller. The unit has 3 DMX channel, so set the No. 1 unit’s address 001, No. 2 unit’s address 004, No. 3 unit’s address 007,
and so on.
2. Configuration Setup
While the display is locked( initial stage of the display), press the ENTER for more than 3 seconds to unlock it, then press
UP or DOWN to find the menu of Config Setup and press ENTER to enter sub-menus. Press UP or DOWN to find
secondary submenus of Dimming, Focusing, LCD display, Language and Display Inversion.Press ENTER if the submenu is
8 / 12
desired, then change the parameters after pressing UP or DOWN. At last press ENTER to save it and go back to the upper
level menu.
3. Information
While the display is locked( initial stage of the display), press the ENTER for more than 3 seconds to unlock it, then press
UP or DOWN to find the menu of Information and press ENTER to enter sub-menus. Press UP or DOWN to find
secondary submenus of LED Temperature, Fixture Time and Software Version. Press ENTER if the information is desired.
4. Manual Dimming
At the initial stage of the display (after the exit of menu) and without DMX signal, 0-100% linear dimming is available by
potentiometer Knob.
5. Reset Test
Automatic reset will be done after first Power-on or re-Power on after a Power-off. While reset, the control panel will display
big “PR” Logo. After reset, the control panel will display some information about logo, product model, a fixture’s DMX
address and etc ,and fixture’s angle be adjusted to the one before last power-off. During the reset, there may be some strange
sounds like “Du Du” for about 20 seconds ,but this is a normal phenomenon.
Dimmer Priority Sequence.
Priority Sequence: Digital Operation Panel> DMX Dimmer> Potentiometer Dimmer
1. Under Menu Mode, Potentiometer Dimmer doesn’t work.
2. Under Menu Mode, DMX works normally excluding Dimmer Function.
3. If the menu is under Dimmer Mode, DMX Dimmer & Potentiometer Dimmer don’t work.
MAINTENANCE
To prolong the life of the unit, it is very important to do the maintenance work. If the unit is idle for a long time, damp,
smoke or particularly dirty surroundings can cause greater accumulation of dirt on its cover and housing. So it should be
cleaned to maintain an optimum light output and at the same time to prevent it from being corrupted by acid gas.
Cleaning frequency depends on the environment in which the fixture operates. Soft cloth and typical glass cleaning products
should be used for cleaning. It is recommended to clean unit at least once every 20 days.
Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.
TROUBLESHOOTING
PROBLEM
ACTION
The unit doesn’t switch on
Power connection is not correct.
Power supply is damaged or abnormal. Call a qualified personnel to fix
it.
Connection of control board is not correct. Call a qualified personnel to
fix it.
The unit can be turned on, but LEDs do
not emit light and are out of control.
Connection of LED board is not correct. Call a qualified personnel to fix
it.
The lamp comes on but the unit doesn’t
respond to the controller
Make sure that the unit is correctly configurated.
Replace or repair the DMX cable.
The beam appears dim
The unit is too hot. Take ventilation measures to make it cool.
9 / 12
TECHNICAL DATA
VOLTAGES:
100V -240V AC，50/60Hz
POWER CONSUMPTION:
280W@220V
LED:
Power consumption
250W
Quantity
1pc
Manufacturers Rated LED Life
50000 Hours
COLOUR TEMPERATURE:
PR-3203T: 3200±250
PR-3203D:5600±250
Luminous Flux
PR-3203D: 14°：7100 lm，48°: 10700 lm
PR-3203T: 14°：5300 lm，48°: 8300 lm
CRI
Ra≥93
DIMMER:
0-100% linearly adjustable
Zooming
Motorized Zooming is available
BEAM ANGLE:
Field angle(1/10 peak) θ 14°- 48°
CONTROL:
DMX512, 5 pin interfaces
HOUSING:
High-intensity aluminum alloy, IP20
WORK ENVIRONMENT TEMPERATURE:
-20°C~40°C
NET WEIGHT:
16KG
10 / 12
SIZES: 670x355x520mm
Light Output
Luminous Flux
11 / 12
ELECTRICAL DIAGRAM
COMPONENT ORDER CODES
NAME
PART NO.
QUANTITY
REMARK
SIGNAL CABLE
230090003
1
5m
POWER SWITCH
192010182
1
HLG-320H-48
DRIVER BOARD
230060288
1
DIGITAL DISPLAY BOARD
230060290
1
LED LIGHT SOURCES
150020278
1
CT 5600K
LED LIGHT SOURCES
150020277
1
CT 3200K
12 / 12
PR LIGHTING LTD.
PR New Hi-tech Science Park, 1582 Xingye Avenue
Nancun Panyu, Guangzhou, 511442 China
TEL: +86-20-3995 2888
FAX: +86-20-3995 2330
P/N:320020223
Version: 20140804
Loading...