Principal LED Street Wrap Gen 2 Installation Manual

INSTALLATION GUIDE
P-LED.com
(325) 227.4577
GETTING STARTED
Inspect the boxes for damage and check the parts against the supplied parts list.
Note: Report damaged parts or shortages immediately to prevent job slowdown/stoppage to place of purchase.
Refer to the Build-A-Border document provided on our webiste at P-LED.com/street-wrap-gen-2 and conrm job measurements.
Lay out your job on paper, making note of Power Supply placement. Power Supplies can be placed at the end of runs or side by side to power allowable linear footage in each direction.
COMPONENT IDENTIFICATION & REQUIRED TOOLS
MATERIALS
Aluminum Extrusion Lens (Acrylic) Mounting Clip Prole Dimensions w/ Mounting Clips Acrylic, UV and impact resistant Aluminum Street Wrap 1.25”W x 96”L x 2.1875”H
REQUIRED TOOLS
• 25' Measuring Tape
• 100' Measuring Tape Framing Square
• Square -1’
• Phillips Screwdriver
• Portable Rechargable Drill
-5/16" hexbit and unibit
-Masonry bits (If brick wall)
• Extension Cord
• Phillips Screwdriver
24VDC LIGHT TAPE SPECS
ELECTRICAL
CONTENTS
Input 100-277VAC Output 24VDC Maximum Load 96W Current at Max. Load 4A
1.
2.
3.
Note: If job measurements do not correspond to provided drawing, call Principal LED immediately at (325) 227-4577. Remember: No more than four (4) 96” units per 96W Power Supply.
Following these few simple steps will ensure a successful installation each time.
Read all instructions before starting installation.
Color W/Ft. W/Unit
Pure White 2.75 22
Red 2.75 22
Blue 2.75 22
Green
2.75 22
*RGB 2.75 22
• Sawzall or Compound Saw
• Carpenter Pencil
• Caulk Gun
• Box Knife
• Wire Strippers
• Wire Snips
• Laser Tool or Chalk Line Substitute Fasteners for the Application if Applicable
W
warranty
5P 5
L
Page 2 Mounting Bracket Layout Page 3 Installing Street Wrap into Mounting Brackets Page 4 How to Wire RGB Page 5 Custom Cut to Fit End of Runs & Corners Page 6 Corner Mounting Options Page 7 Mounting on Incline or Vertically Page 8 Connecting Transformers
24V Light Tape comes pre-installed.
LED TUBE X-C-SR2-ULXX
LED TRACK X-C-SR2-BASE
MOUNTING BRACKET A-SR2-BKTS
END CAP A-SR2C-ECYY
ANGLE BRACKET
QWIK BOX™
96W Power Supplies
PL-96-24-U (P-OH096-24-PL)
INSIDE CORNER PIECE A-SR2C-CIYY
OUTSIDE CORNER PIECE A-SR2C-COYY
PLTC CABLE PL-LE3-PLTC-18-2
MIDDLE CONNECTOR A-SR2C-MXYY
YY = Blue (BL), Green (GR), Red (RD), White (WH)
STREET WRAP GEN 2™ MOUNTING BRACKET LAYOUT
1.
Use a chalk line, gauge, laser level, or other means to be certain the run is straight, marking locations for brackets.
Install three (3), evenly spaced, mounting brackets per section. Ensure there are at least two inches between the end of the track and the mounting bracket as shown in the picture above.
Use a 0.125” drill bit to add a drain hole in lens in the center of the run. Never drill drain hole when installed on the LED base.
2.
3.
Note: There must be a 0.1875” space left between each section when using middle or corner connectors.
NOTE: MAXIMUM 4 UNITS PER 96W POWER SUPPLY
120 or 277 VAC
96W Power Supply
384”
96”
2
4.375”
Loading...
+ 7 hidden pages