Princeton VL1514 User Manual

DIGITAL

VL

REFERENCE MANUAL

1514

LCD MONITOR USER’S MANUAL

GETTING STARTED.......................................................................... 1

I

NTRODUCTION ................................ ERROR! BOOKMARK NOT DEFINED.

FEATURES......................................... ERROR! BOOKMARK NOT DEFINED.

UNPACKING AND CHECKING OF THE PACKAGE CONTENTS........ ERROR!

BOOKMARK NOT DEFINED.

INSTALLING THE MONITOR .....................................................................2

CONNECTING YOUR MONITOR TO PC ....................................................3

ADJUSTING THE VIEWING ANGLE ...........................................................3

OPERATING THE MONITOR....................................................... 4

HOW TO USE THE OSD (ON SCREEN DISPLAY) ......................................4

THE ADJUSTMENT OF MONITOR’S SCREEN DISPLAY................................4

MENU TABLE............................................................................................5

FOR YOUR SAFETY ..........................................................................6

SPECIAL NOTES ON LCD MONITORS...................................7

CLEANING ........................................ ERROR! BOOKMARK NOT DEFINED.

SUPPORTED TIMING......................... ERROR! BOOKMARK NOT DEFINED.

TROUBLESHOOTING PROCEDURES.......................................................... 8

OWER MANAGEMENT ............................................................................8

P

CONFORMITY AND COMPLIANCE.........................................9

GETTING STARTED

WARNING: Do not operate the LCD monitor with unspecified power supply. Usage of
incorrect voltage will cause malfunction and may cause fire or electric shock.

Introduction

Bright and sharp images of text and graphics are what you will find with the LCD color
monitor. The LCD monitor provides a maximum resolution of 1024 x 768 pixels with a
flicker-free display at up to 75Hz refresh rates that offers bright, sharp and vibrant color
display without the radiation emission and hazards of CRT monitors.

Features

˙15.0” TFT active matrix color crystal displays
˙Supports XGA resolution of 1024 x 768 pixels
˙Energy Star® Compliant

˙Multi-scan functions of XGA 1024 x 768, SVGA 800 x 600, VGA 640 x 480, 720

x400, and 640 x 350 for a perfect graphics performance

˙Digital Character Smoothing
˙Automatic Set-Up
˙Ergonomic Design: TCO Approved
˙VESA® DDC2B Plug & Play Compliant
˙VESA® Wall/Arm Mount
˙Versatile, functional & User friendly OSD

˙Plug & Play: Conform to the VESA standards and support DDC1/2B spec.
˙Extra slim design to maximize your desk space

Unpacking and Checking of the Package Contents

Before unpacking your LCD Monitor, prepare a suitable workspace for your LCD
Monitor and computer. You need a stable, level, and clean surface near a wall outlet.

1. Set the LCD Monitor box in an upright position and open from the top of the box

before removing the right/left cushions.

2.

Remove the back cover from your monitor (pull from the bottom of cover to open)
to install your PC system.

Accessories

1 pc 1 pc 1 pc 1 pc

AC/DC Adaptor Power Cord Audio Cable

(Optional)

1

User’s Manual

Installing the Monitor

z DO NOT install the monitor where sudden temperature changes may occur, or in

humid, dusty, or smoky areas as it may cause fire, electric shock or damage.

z DO NOT place your LCD Monitor near a window as it may be severely damaged if

exposed to rain, water, moisture, or sunlight.

z MAINTAIN good ventilation; covering of ventilation slots or holes may cause fire.
z PLACE the monitor at least 4” (or 10 cm) way from the walls.
z SAFE storage temperature of the LCD Monitor is in a range of –20 to +65℃.

HOW TO INSTALL YOUR LCD MONITOR

1) Assemble the base plate included in the accessory kit.

Hold the base plate with
one hand and the stem of
the monitor with the other
hand (the monitor should
be in an upright position).

Position the monitor with the back facing you;
secure the base plate with your fingers and push
the stem of the monitor in towards you with your
thumbs. When you hear a click sound, then it is
securely locked-in. (check and make sure that
the security clip is properly locked-in).

2) Check and make sure that the Signal Cable is connected to the PC Video card.

3) Plug the female end of the 1.8m power cord into the AC adaptor. Then, plug
the DC connector of the adaptor to your monitor’s DC jack.

4) When you’ve completed the above steps, connect the male end of the power
cord into a wall socket.

 Audio in

(optional)

 Signal cable Connected with PC Video card

 DC Jack Plug into the AC power adapter.

Connect with your audio device.

Gently slide the stem
of the monitor into
the base plate slot.

NOTE

For added protection, it is recommended to use a Surge Protection device plugged between the
AC Adapter and the electrical wall outlet to prevent the effects of sudden current variations
from reaching the LCD Monitor. Sudden peaks of electricity may cause damage to the Monitor.

2

Connecting Your Monitor to PC

(1) Connecting Video (See Figure 1)

A. Turn off your PC and the LCD Monitor before connecting your monitor to the PC.

B. Use the built-in VGA Signal Cable to connect your Monitor with the PC.

(Make sure the signal cable is securely connected to the PC’s VGA port.)

C. Then tighten the connecting screws to ensure a secure connection.

D.

Turn on your computer, and then turn on your LCD Monitor.

Adjusting the Viewing Angle

Your LCD Monitor is designed to allow you to adjust it to an optimal viewing angle.
You can adjust the monitor upward to 20 degrees and downward to -5 degrees.

NOTE

Do not touch the screen while changing the viewing angle.
It may damage the screen. Make sure not to catch your
fingers while changing the viewing angle.

3

OPERATING THE MONITOR

A

The LCD monitor has been preset at the factory with the Timing shown in Appendix to create optimal
picture. Users are also able to adjust the picture to the desired brightness and sharpness by following
the instructions.

How to Use the OSD (On Screen Display)

OSD function allows the user to easily adjust the display to the desired quality. The OSD menu includes
a main menu and a sub-menu.

Structure of OSD Menu

The adjustment of monitor’s screen display

There are two ways to adjust the monitor’s screen, i.e. auto adjustment and manual adjustment.

uto adjustment

1. Power ON the LCD monitor and computer.

2. Make sure that your LCD monitor is not

“CONTROL-LOCKED” by pressing “f “ and
“-“ simultaneously.

3. Press”-“ to unlock. The “CONTROL LOCK”
screen will disappear automatically or you
may press “EXIT” to exit from the screen.

4. Press either the “d” or “f “ to pop-up the
OSD screen.

5. Select “AUTO SETUP” of OSD screens by
pressing the“d” button to “AUTO SETUP”.

6. Press “+” button while displaying “AUTO
SETUP” screen.

7. The auto adjustment is started. “AUTO
SETUP” will be displayed during auto
adjustment. It takes a few seconds to finish
adjustment.

1 EXIT Button Exit the OSD (On Screen Display).
2 dArrow key Press to select main menu items.
3XArrow key Press to select sub menu items.
4“-” Minus

key

5“+” Plus key Adjust setting bars i.e. CONTRAST,

6 Power For turning ON/OFF the monitor.
7LED power

status display

Adjust sub-setting bars i.e. CONTRAST,
BRIGHTNESS, etc. to decrease setting
values of the OSD.

BRIGHTNESS, etc. to increase setting
values of the OSD.

Green – Normal operation
Amber –< 5W when receiving no
horizontal and/or vertical sync signal)

Operating Procedure

1. Power on the LCD monitor.

2. Press “d” or “f “ to pop up OSD menu.

3. Press “d” to select main menu item.

4. Press “f “ to select sub menu item.

5. Press “+” and “-“ buttons to adjust.

6. Press the EXIT button when finish adjusting.

4

Manual adjustment

a) Power ON the LCD monitor and computer.
b) Adjust according to the previous “Operating Procedure” and “Menu Table” to adjust the screen to

your favorable screen display.

OSD Adjustment Lock

This function is used to prevent changing the adjusted settings by mistake. All the adjusting items
except “BRIGHTNESS” will be locked.

a) Press the “f” and “-“ buttons simultaneously

and the “CONTROL LOCK” screen is displayed.

b) Press “+” button, and it will become “CONTROL

LOCK’ status. The “LOCKED” will be displayed in
the up-right corner of screen indicating that OSD is
in locked position.

c) To release the “CONTROL LOCK’, press “f” and

“-“ buttons simultaneously and “CONTROL LOCK”
screen will appear. Press “-” button to release the
“CONTROL LOCK’. The “CONTROL LOCK”
screen will disappear automatically.

d) Volume control: directly push “+” and “-“ button to turn up/down audio volume.

Menu Table

Main Menu Sub Menu

BL

Function Name Function

BRIGHTNESS Adjusts the level of brightness and darkness.

CONTRAST Adjusts the RGB color pattern set of the contrast.

BLACK LEVEL Adjusts the level of darkness on black portion.

VOLUME

DISPLAY MODE

(optional) Adjust the volume of built-in speaker.

CLOCK Adjusts the number of pixels from source video.

CLOCK PHASE Adjusts the phase relative to video Hsync signal.

HORIZONTAL

POSITION

VERTICAL

POSITION

AUTO SETUP To auto adjust press the “+” button.

AUTO ADJUST

ALL RESET Return to factory preset value

OSD POSITION Changes the OSD position.

POWER SAVE Power management function

LANGUAGE Press “+” and “-” to choose OSD language

COLOR

Moves the screen horizontally (left/right)

Moves the screen vertically (up/down)

Automatically adjusts the clock, phase, H/V position
values for the most optimal settings.

“-“ Represents the TEXT mode.
“+” Represents the GRAPHIC mode.
(For resolutions lower than 1024 x 768)

STANDARD: Factory preset color
CUSTOM: Preferred color is adjusted.

5

FOR YOUR SAFETY

WARNING

ALWAYS OPERATE UNDER SPECIFIED POWER SUPPLY

Usage of incorrect voltage will cause malfunction and may cause fire or electric shock.

PROTECT and CORRECTLY USE THE CABLE

Do not pull or bend the power cable and signal cable or place the monitor or any heavy objects on the
cables. If the cables are damaged, they may cause fire or electric shock.

IMMEDIATELY STOP OPERATING THE MONITOR WHEN YOU DETECT ANY
ABNORMAL OCCURENCE

If you notice any abnormal phenomenon such as strange noise, smoke or smells, unplug the monitor
and contact your dealer or the nearest service center immediately.

DO NOT DISASSEMBLE

Disassembly may expose you to the danger of fire or electric shock.

DO NOT PUT ANY FOREIGN OBJECT INSIDE THE MONITOR

It may cause fire, electric shock or damage when operating the monitor with foreign objects inside.

DO NOT USE THE MONITOR NEAR WATER

Operating the monitor in close proximity to water where the water may be spilt or splashed onto the
monitor may cause fire or electric shock.

BAD WEATHER CONDITIONS

It is advisable not to operate the monitor during heavy thunderstorms as intermittent breaks in power
may cause malfunction. Do not touch the plug under these circumstances as it may cause electric
shock.

CAUTION

DISCONNECT CABLES WHEN MOVING THE MONITOR

When moving the monitor, always turn off the switch, unplug the monitor, and disconnect the signal
cable. If the cables are not properly disconnected when moving the monitor, it may cause fire or electric
shock.

DO NOT TOUCH THE PLUG WITH WET HANDS

Pulling or inserting the plug with wet hands may cause electric shock.

HOLD THE PLUG WHEN DISCONNECTING

To disconnect the power cable or signal cable, always pull the cable by the plug. Never pull on the
cable as this may cause fire or electric shock.

OTHERS

ERGONOMIC RECOMMENDATIONS

Do not operate the monitor in a dark room or against a bright background. For optimal viewing comfort,
the monitor should be just below eye level and 40-60 cm (16-24 inches) away from your eyes. When
using the monitor over a prolonged period of time, a ten-minute-break per hour is recommended.

6

SPECIAL NOTES ON LCD MONITORS

The following are normal with LCD monitors and do not indicate a problem.

z When first turning on the LCD monitor, if the picture does not fit in the display area, it is because

of the type of computer that is used. In such case, adjust the picture position to its correct
position. (See Operating the Monitor)

z The screen may flicker during initial use. Turn off the power switch and then turn it on again the

flickering should disappear.

z Users may notice a little uneven brightness on the screen depending on the desktop pattern they

use. It is normal for LCD monitors to show such uneven brightness.

z Due to the nature of the LCD screen, switching of images after a prolonged period of time of

displaying the same image, the image from the previous screen may remain. In such case, the
screen is recovered slowly by changing the image or turning off the power switch for hours.

Cleaning

CAUTION

z For safety reasons, turn-off the power switch and unplug the monitor before cleaning.
z Do not scratch or rub the screen with a hard object.
z Never use any of the following solvents on the LCD monitor. Such harsh chemicals may cause

damage to the cabinet and the LCD screen.

Thinner Spray-type cleaner Benzene Wax Abrasive cleaner Acid or Alkaline solvent

z Rubbing the cabinet with products made of rubber or plastic for a long period of time may cause

degeneration or loss of paint on the cabinet.

Cabinet

z Remove dirt with a lightly moistened cloth and a mild solvent detergent. Then wipe the cabinet

with a soft dry cloth.

LCD

z Periodic cleaning with a soft dry cloth is recommended.
z Do not use tissue to clean the screen. It may damage the LCD screen.

Supported Timing

Analog

VESA

Macintosh VGA

MS-DOS 640 x 350 31.5 KHz 70.1 Hz

Display Mode

VGA

SVGA 800 x 600

XGA 1024 x 768

Horizontal Frequency Vertical Frequency

640 x 480

720 x 400 31.5 KHz 70.1 Hz

640 x 480 35.0 KHz 66.7 Hz
832 x 624 49.7 KHz 74.6 Hz

31.5 KHz 60.0 Hz

37.5 KHz 75.0 Hz

35.1 KHz 56.3 Hz

37.9 KHz 60.3 Hz

46.9 KHz 75.0 Hz

48.1 KHz 72.0 Hz

48.4 KHz 60.0 Hz

56.5 KHz 70.0 Hz

58.1 KHz 72.0 Hz

60.0 KHz 75.0 Hz

7

Troubleshooting Procedures

y

Please follow the following steps for a possible solution.

1. Perform the adjustments according to Operating the Monitor.

2. Refer to the following items if you cannot find a proper item listed in the Operating the Monitor or if

the problem remains.

3. If the problem you have experienced is not described below or you cannot correct the problem,

stop using the monitor and contact your dealer or the nearest service center for further assistance.

PROBLEM CHECK TO SEE

No Display.

a) Power indicator
does not light up.

b) Power indicator
is green.

c) Power indicator
is amber.

Display is too dark

or too bright.

Display is not in the

center.

Display is shaking.

Display is not

synchronized.

4. When “ATTENTION” is displayed:

If the power cord is firmly plugged in the socket.
If the power switch is turned on.
If the AC socket is OK. Please check using another piece of equipment.
If the blank screen saver is active, touch the keyboard or mouse.
Increase the CONTRAST and/or BRIGHTNESS.
If the computer is ON.
If the signal cable is properly connected.
If the signal timing of the computer is within the spec of the monitor.
If the monitor is on power management mode, touch the keyboard or the mouse.
If the computer is ON.
If the signal cable is properly connected.
If the signal timing of the computer is within the spec.

If the video output level of the computer is within the spec.

If the signal timing of the computer is within the spec.

If the power voltage is within the spec.
If the signal timing of the computer is within the spec.
If the signal cable is properly connected.
If the signal timing of the computer is within the spec.
If the video output level of the computer is within the spec.

a. “POWER MANAGEMENT” is set to “OFF”
(1) Check if the signal cable is connected correctly to the computer.

(2) Check if the cable is broken.

After 5 seconds

b. “POWER MANAGEMENT” is set to “ON”
(1)

Check the signal cable is connected

(2) Check the cable line is broken

of Displa

(3) Check the “P

function is operated correctly

OWER MANAGEMENT”

Power Management

The LCD Monitor complies with the VESA DPMS (version 1.0p) power management proposal. The
VESA DPMS proposal provides four phases of power saving modes by detecting the horizontal or
vertical sync signal.

Item DPMS Mode Display

1 On Normal Green Normal --- On On
2 Off No Display Amber

Power

LED

Power

Consumption

≦ 5W

Recovery

Time

H-sync V-sync

3 sec <10KHz <10Hz

8

CONFORMITY AND COMPLIANCE

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a residential installation. This device
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this device does cause harmful
interference to radio or television reception (this can be determined by turning, the device off and on),
you are encouraged to try to correct the interference by one or more of the following measures:

Caution:
To comply with the limits for an FCC Class B computing device, you should use the shielded signal
cord and power cord supplied with this unit. The Federal Communication Commission warns that
changes or modifications of the unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

Radio Frequency Interference Statement

Warning:

This is a Class B product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.

*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and the receiver.

*Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

*Consult the dealer or an experienced radio/TV technician for help.

Canadian Doc Notice

For Class B Computing Devices

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus as set out in the Radio Interference Regulation of the Canadian Department of
Communications.

CE MARKING DECLARATION OF CONFROMITY

The LCD monitor complies with the requirements of related European standards,
which include:

z Emission: EN 55022, EN 61000-3-2, EN-61000-3-3
z Immunity: EN 50082-1
z Safety: EN 60950 [Low-Voltage Directive (73/23/EEC)

ENERGY STAR

This product meets the Energy Star guidelines for energy efficiency.

TCO’99 (White Color Only)
TCO’95 (For All Colors)

Congratulations! You have just purchased a TCO’99/TCO’95 approved and labeled
products. Your choice has provided you with a product developed for professional use.
Your purchase has also contributed to reducing the burden on the environment and
also to the further development of environmentally adapted electronics products.

9

www.princetongraphics.com

Part No.: 14AP1511A00
Ref No.: 00300000348

© 2003 Princeton Digital (USA) Corp. All right reserved. This manual may not be copied in whole or in part without the written consent of Princeton Digital (USA) Corp. Product Specifications are

subject to change without notice. Princeton Digital (USA) Corp. is not responsible for printing or clerical errors. Windows® is a registered trademark of Microsoft Corporation. Apple® and

MacintoshTM are registered trademarks of Apple Computer, Inc. Energy Star® is a U.S. registered trademark. As an Energy Star® Partner, Princeton Digital (USA) Corp. has determined that this

product meets Energy Star® guidelines for energy efficiency .