Princeton SENergy 714 Reference Manual

Table of Contents

Tips and safety precautions................................................................................................................................. 2

Product description ............................................................................................................................................. 3

Height adjustment, angle adjustment.................................................................................................................. 4

Connecting the monitor and turning the monitor on and off.............................................................................. 5

Connecting the monitor to a computer........................................................................................................... 5

Connecting the monitor to a power source .................................................................................................... 6

Turning the power on..................................................................................................................................... 6

Changing between input terminals................................................................................................................. 7

Turning the power off .................................................................................................................................... 7

Adjusting the screen display and speaker volume.............................................................................................. 8

Adjusting the backlight .................................................................................................................................. 8

Adjusting the speaker volume........................................................................................................................ 9

Setting GAMMA ........................................................................................................................................... 9

Adjusting the screen display (When using an analog signal) ........................................................................... 10

Automatic screen adjustment....................................................................................................................... 10

Manual screen adjustment............................................................................................................................ 11

Adjusting the screen display (When using a digital signal)............................................................................. 14

Monitor care and repair .................................................................................................................................... 16

Monitor care................................................................................................................................................. 16

Storage ......................................................................................................................................................... 16

Troubleshooting ........................................................................................................................................... 16

Specifications.................................................................................................................................................... 17

Instructions for attaching a VESA compliant arm............................................................................................ 20

1

Tips and safety precautions

- The TFT color LCD panel used in this monitor is
made with the application of high precision
technology. However, there may be minute
points on the screen where pixels never light or
are permanently lit. Also, if the screen is viewed
from an acute angle there may be uneven colors
or brightness. Please note that these are not
malfunctions but common phenomena of LCD's
and will not affect the performance of the
monitor.

- Do not leave the screen displaying idly for long
periods of time, as this could cause afterimage to
Remain.

- If the brightness is adjusted to the minimum
setting it may be difficult to see the screen.

- The quality of the computer signal may influence
the quality of the display. We recommend using a
computer able to emit high quality video signals.

- Never rub or tap the monitor with hard objects.

- This monitor and its accessories may be
upgraded without advance notice.

Location

- Do not use the monitor where ventilation is poor,
where there is a lot of dust, where humidity is
high, or where the monitor may come into
contact with oil or steam, as this could lead to
fire.

- Ensure that the monitor does not come into
contact with water or other fluids. Ensure that no
objects such as paper clips or pins enter the
monitor as this could lead to fire or electric
shock.

- Do not place the monitor on top of unstable
objects or in unsafe places. Do not allow the
monitor to come into contact with strong shocks
or vibrations. Causing the monitor to fall or
topple over may damage it.

- Do not use in places where the monitor will be
subject to direct sunlight, near heating equipment
or anywhere else where there is likelihood of
high temperature, as this may lead to generation
of excessive heat and outbreak of fire.

The Power Cord

- Do not damage the power cord nor place heavy
objects on it, stretch it or overly bend it. Also, do

not add extension cords. Damage to the cord may
result in fire or electric shock.

- Use only the power cord supplied with the
monitor.

- Insert the power plug directly into the AC outlet.
Adding an extension cord may lead to fire as a
result of overheating.

Monitor and accessory checklist

- Please check that the following items are included
in the Package.

- LCD monitor (1)

- Analog signal cable (1)

- Audio cable (1)

- DVI-D 24 pin – DVI-D 24pin (1)

(model name: L17HMN 00ABA)

- Power cord (1)

- Operation manual (1)

Notes:

- Use only the cables supplied with the monitor or
designated cables that are separately purchased.

- The analog signal cable (DVI-I29 pin – mini
D-sub15 pin) is to be purchased separately.

(model name: L17HMN 00ABA)

- Be sure to use cables that are less than 3 m in
length.

- You are advised to retain the carton in case the
monitor needs to be transported.

Manual Scope

- In the booklet, Microsoft Windows XP will be
referred to as "Windows XP", Microsoft Windows
Millennium as "Windows Me", Microsoft
Windows 2000 as "Windows 2000", Microsoft
Windows 98 as "Windows98", Microsoft
Windows 95 as "Windows 95”, and Microsoft
Windows Version 3.1 as "Windows 3.1". When
there is no need to distinguish between programs,
the term "Windows " will be used.

2

Product description

1. INPUT button--------------------------- To switch between the signal's input terminals.

2. MENU button--------------------------- This button is used to pop-up, select and close the OSD (On Screen
Display) Menu.

3. d/ MODE button----------------------- When the OSD Menu is displayed:

This button is used to select menu options.

When the OSD Menu is not displayed:

This button is used to set DISPLAY MODE.

4. ef buttons------------------------------ When the OSD Menu is displayed:

These buttons are used to select an option or adjust the value of
the selected option.

When the OSD Menu is not displayed:

These buttons are used to adjust backlight brightness and speaker

volume.

5. Power button----------------------------- Pressing this button turns the power on.
Press the button again to turn the power off.

6. Power LED------------------------------- This LED is lit green when in use and orange when in power-saving
mode.

7. Speakers---------------------------------- Audio entering via the external device connected to the monitor can
be heard.

8. Power terminal

9. DVI-I input terminal-------------------- The computer’s digital RGB output terminal or analog RGB output
terminal can be connected here.

Separately sold cables are necessary for connection.(p.5)
For a digital singal input: It can be connected to a computer with a

DVI-compatible output terminal (DVI-D24 pin or DVI-I29 pin) and
which has SXGA output ability. Depending on the computer to be
connected, correct display may or may not be possible.

10. Analog RGB input terminal---------- The analog signal cable is connected here. The analog signal cable
included should be used.

11. Audio input terminal------------------ A computer’s audio output terminal can be connected here. The
audio cable included should be used.

12. Security lock anchor------------------ By connecting a security lock (commercially available) to the

security lock anchor, the monitor is fixed so that it cannot be
transported.

The security slot works in conjunction with Kensington Micro
Saver Security Systems.

13. Ventilation openings------------------- Note: Never block the ventilation openings as this may lead to

overheating inside the monitor and result in malfunction.

3

Height adjustment, angle adjustment

CAUTION!

- Pressure from hands on the LCD panel could cause
damage.

- Do not attempt to move the monitor beyond its
movement range. Applying excessive force to move
the monitor may damage the product.

- Be careful not to allow your fingers to be pinched.

Height adjustment

- When positioning the display higher, hold the stand

tight so that it does not move together with the
display.

Angle adjustment

4

Connecting the monitor and turning the monitor on and off

CAUTION!

- When connecting, ensure that both the monitor
and computer are switched off.

- Be careful not to overly bend the cable or add
extension cords as this could lead to a malfunction

Connecting the monitor to a computer

Connecting using accessory analog signal cable

Connect the analog signal cable to the analog RGB
output terminal of the computer.

- For analog connection, use the analog signal cable
accessory or a commercially available one (both
ends should be mini D-sub 15 pin).

When connecting using separately sold digital or
analog or analog signal cables

The separately sold display cable enables
connection between the DVI-I input terminal on the
monitor and the digital or analog RGB output
terminal of the computer.

When connecting to a digital RGB output
terminal:

- Use a digital signal cable.

- For digital RGB connection, the monitor has an
input for connecting to a computer with a DVI
compatible output connector (DVI-D24 pin or
DVI-I29 pin) and SXGA output capability.
(Depending on the type of computer to be
connected, the display may not work correctly.)

When connecting to an analog RGB output
terminal:

- Use an analog signal cable.

- Paying attention to connector direction, firmly
insert the signal cable vertically into the connector,
and then tighten the screws at both sides.

If connecting to a D-sub 15 pin 2 rows Apple
Power Macintosh, attach a Macintosh conversion
adapter (commercially available) to the analog
signal cable.

Note:

- If connecting to the Sun Ultra series, a conversion
adapter (commercially available) may be required.

- Paying attention to connector direction, firmly
insert the signal cable vertically into the connector,
and then tighten the screws at both sides

Connect the accessory audio cable

When the accessory audio cable is connected to the
audio output terminal of the computer, the sound of
the connected computer is output from the monitor
speakers.

5

Connecting the monitor and turning the monitor on and off

Connecting the monitor to a power
source

Turning the power on

1. Press the monitor's POWER button.
The power LED will light up orange.

2. Turn on the computer.

When a signal is input from the computer, the
power LED lights up green, and the screen is
displayed. (After power is turned on, it may take a
little time until the screen is displayed.)

Notes：

- If the input terminal to which the computer is
connected has not been selected, the screen will not
be displayed. If necessary, perform input terminal
switching. (P7.)

- When using an analog signal, perform an automatic
screen adjustment under the following conditions
(P10.)

- Using the monitor for the first time.

- After having changed the system settings during
use.

- When connecting to a notebook, if the notebook
computer's screen is set so that it is displaying at
the same time, the MS-DOS screen may not be able
to display properly. In this case, change the settings
so that only the monitor is displaying.

6

Connecting the monitor and turning the monitor on and off

Changing between input terminals

Use the INPUT button to switch between signal
input terminals

Note：

- When there is no input signal, [NO SIGNAL]

Is displayed.

Turning the power off

1. Turn the computer off.

2. Press the monitor's POWER button.
The Power LED will disappear.

If the monitor will not be used for a long time,
turn off the main power switch of the monitor,
and remove the power plug from the outlet.

7

Adjusting the screen display and speaker volume

For analog signal

1. First perform an automatic adjustment. (P10)

2. Perform manual adjustment where necessary.
(P11)

For digital signal
The monitor can generally be used without
adjustment. If necessary perform manual
adjustment. (P14)

Note：

- All adjustment will be saved even after turning the
power off.

Resetting all adjustment values
All adjustment values can be returned to their
original ex-factory values in one command.

1. Turn off the monitor power.

2. Press the MENU button and the d/ MODE

button simultaneously, and while doing this press

the power button (i.e. turn the power on).
Continue to press the buttons until [ALL RESET]
appears on the screen. Reset is complete when
the displayed message disappears.

Note：

- While [ALL RESET] is displayed, the control
buttons are displayed.

- It is not possible to reset values when the
adjustment lock is in place. Remove the
adjustment lock before attempting to operate
control buttons.

SCREEN menu reset

Setting of items in the SCREEN Menu (CLOCK,
PHASE, H-POS, V-POS) can be returned to their
original ex-factory values.

1. Turn on the monitor power

2. Press the MENU button and the ebutton

simultaneously. When [RESET] appears on the
screen, the reset is complete.

Note：

- It is not possible to reset values when the
adjustment lock is in place. Remove the
adjustment lock before attempting to operate
control buttons.

Adjustment lock function

By disabling the control buttons (i.e. setting the lock)
any attempted changes to adjusted values will be
voided.

1. Turn off the monitor power.

2. While pressing the MENU button, press the
power button (i.e. turn power on).

Continue to press the buttons until
[ADJUSTMENT LOCKED] appears on the
screen.
The lock is set when the message is displayed.

Note：

- When the lock is in place, all buttons other than

the power button are disabled.

Adjustment lock release

1. Turn off the monitor power.

2. While pressing the MENU button, press the
power button (i.e. turn the power on).

Continue to press the buttons until
[ADJUSTMENT UNLOCKED] appears on the
screen. The lock is released when the message is
displayed.

Adjusting the backlight

1. Without the OSD Menu being displayed, press

the eor the f button.

2. Check that [BACKLIGHT] is selected.

If it is not selected, press the d/ MODE button

and select [BACKLIGHT].

VOLUME 31

BACKLIGHT 31

3. Adjust by pressing the ebutton (darker) or f
button (lighter).

Note：

- On Screen display for adjustment disappears
several seconds after the last operation.

8

Adjusting the screen display and speaker volume

Adjusting the speaker volume

1. Without the OSD Menu being displayed, press

the eor the f button.

2. Check that [VOLUME] is selected.
If it is not selected, press the d/ MODE button

and select [VOLUME].

VOLUME 31

BACKLIGHT 31

3. Adjust by pressing the ebutton (darker) or f

button (lighter).

Note：

- On Screen display for adjustment disappears
several seconds after the last operation.

Setting GAMMA

Color tone or brightness can be changed with one
Command.

GAMMA1

Displays image with the color tone results from
original scheme of liquid crystal panel.

GAMMA2

Display brightness is lowered. The brightness is
set to a level that is easier on the eyes than with
other modes and saves power.

GAMMA3

GAMMA3 color conversion, account of liquid
crystal's characteristics and represents color tone
close to its original image.

GAMMA4

Displays an image with dynamic and GAMMA4
primary colors.

How to set

Press the d/ Mode button when the OSD Menu is
not displayed.
Each time the button is pressed the next menu item
appears. (GAMMA1GAMMA2GAMMA3
GAMMA4GAMMA1)
On Screen display for adjustment for adjustment
disappears several seconds after the last operation.

9

Adjusting the screen display (When using an analog signal)

Automatic screen adjustment

Options in the SCREEN Menu can be adjusted
automatically (CLOCK, PHASE, H-POS, V-POS).

Note：

- When setting up this monitor for the first time or

after having changed an aspect of the current system,
perform an automatic screen adjustment before use.

Adjusting the screen automatically

1. Press the MENU button.
The SCREEN Menu will be displayed.
(Example: Displayed screen of the L17HMN

00ABA)

SCREEN

2. Press the f button.

3. Press the MENU button 4 times to make the On

MANUAL AUTO

MANUAL

CLOCK 127
PHASE 16
H-POS 127
V-POS 32

INPUT-1 ANALOG
1280x1024 V:60Hz H:64.0kHz

The screen will become dark and [ADJUSTING]
will be displayed. After a few seconds the
SCREEN Menu will return. (The automatic
adjustment is now complete.)

Screen Display (OSD) Menu disappear.

Notes：

- In most cases automatic adjustment is sufficient.

- It may not be possible to achieve correct
adjustment with the first automatic adjustment. In
such a case, try repeating automatic adjustment 2
or 3 times.

- If necessary due to any of the following, manual
adjustments (P11) can be performed after the
automatic adjustment.

- When further fine adjustment is needed.

- When the computer's video input signals are

Composite Sync or Sync On Green. (Automatic
adjustments may not be possible.)

- When [OUT OF ADJUST] is displayed. (When

the screen displays an entirely dark image, the
automatic screen adjustment may be disabled.
When marking an automatic adjustment, be sure
to either use the Adjustment Pattern or try
displaying an image that makes the entire
screen very bright.)

- Automatic adjustment may not be achieved

correctly depending on what is displayed on the
screen – moving picture or the MS-DOS prompt
etc.

10

Adjustment the screen display (When using an analog signal)

Manual screen adjustment

Adjustments can be made using On Screen Display
(OSD) Menu provided.

On Screen Display for adjustment

This chapter provides the procedure how to adjust
the screen by using operation Pattern.

How to adjust

- Press the MENU button.
The SCREEN Menu will be displayed.

SCREEN

Note：

- The OSD Menu automatically disappears

SCREEN Menu

MANUAL: Individual menu options are manually

Auto: Every menu option is automatically

MANUAL AUTO

MANUAL

CLOCK 127
PHASE 16
H-POS 127
V-POS 32

INPUT-1 ANALOG
1280x1024 V:60Hz H:64.0kHz

At this point relevant menu options can be adjusted.
Each time the MENU button is pressed the next

menu is selected. (SCREEN GAIN CONTROL
COLORMODE SELECT OSD Menu
disappears)

approximately 30 seconds after the last command.

SCREEN

MANUAL AUTO

MANUAL

CLOCK 127
PHASE 16
H-POS 127
V-POS 32

INPUT-1 ANALOG
1280x1024 V:60Hz H:64.0kHz

adjusted.

adjusted.

Note：

- Press the fbutton to select [AUTO].

- To choose a menu option:d / MODE button

- To go to the next menu: MENU button

CLOCK
This feature will increase or decrease vertical picture

alignments. Normally, Automatic Adjustment
should be used. Note: This is for advanced users.

(efbuttons )

PHASE
This feature will increase or decrease horizontal

picture alignments. Normally Automatic
Adjustment should be used. Note: This is for
advanced users.

(efbuttons )

NOTE：

- Adjustments to [PHASE] should be made only after
[CLOCK] has been correctly set.

H-POS (horizontal positioning) and V-POS (vertical
positioning)

To center the Adjustment Pattern within the
boundaries of the screen, adjust the left-right (H-POS)
values and the up-down (V-POS) values.

(efbuttons )

11

Adjusting the screen display (When using an analog signal)

GAIN CONTROL Menu

GAIN CONTROL

MANUAL: Individual menu options are manually

AUTO: Every menu option is automatically

Notes:

- Press the fbutton to select [AUTO].

- To choose a menu option: d / MODE button

- To go to the next menu: MENU button

*Auto Gain Control function

- The Auto Gain Control adjusts contrast and

- If the signal coming from the computer is

- If [OUT OF ADJUST] is displayed, perform

BRIGHTNESS

This feature changes the brightness level.
(efbuttons )

CONTRAST

This feature changes the contrast level.
(efbuttons )

MANUAL AUTO

MANUAL

BRIGHTNESS 127
CONTRAST 16

INPUT-1 ANALOG
1280x1024 V:60Hz H:64.0kHz

adjusted.

adjusted using the Auto Gain Control*
function.

brightness based on the brightest and darkest colors
of the image displayed. If you are not using the
Adjustment Pattern it is necessary to have black
Area and white area of at least 5 mm ×5mm on the
screen. Adjustment may not be possible without
those areas.

composite sync or sync on green, automatic
adjustment cannot be performed. Please perform
manual adjustment instead.

manual adjustment.

COLOR Menu

COLOR

9300 6500 5000 USER

R-CONTRAST
G-CONTRAST
B-CONTRAST

INPUT-1 ANALOG
1280x1024 V:60Hz H:64.0kHz

6500

Notes:

- Use the efbuttons to select [9300], [6500], [5000]
or [USER].

- Selecting [USER] will display the setting values for
[R-CONTRAST], [G-CONTRAST],
[B-CONTRAST], in order to make fine
adjustments.

- Use the d / MODE button to select
[R-CONTRAST], [G-CONTRAST] and
[B-CONTRAST].

- To go to the next menu: MENU button

9300……Color tone bluer than standard
6500……Color tone standard setting
5000……Color tone redder than standard

USER

R-CONTRAST..…e button for blue-green

f button for red

G-CONTRAST..…e button for purple

f button for green

B-CONTRAST..…e button for yellow

f button for blue

12

Adjusting the screen display ( When using an analog signal )

MODE SELECT Menu

MODE SELECT

Notes:

- Depending on the resolution of the input signal,

- To choose a menu option: d / MODE button

- To complete adjustment: MENU button

OSD H-POSITION (OSD horizontal position)

The position of the OSD Menu can be moved to the
left and right. (efbuttons )

OSD V-POSITION (OSD vertical position)
The position of the OSD Menu can be moved up and

down. (efbuttons )

SCALING (Level of scaling)

The sharpness of the image can be adjusted.
(efbuttons )

Note:

- When the display mode is set to less than 1280 ×

LANGUAGE

You can choose the language used in OSD Menu.

1. Press the fbutton.

2. Use the d / MODE button to choose a language.

3. Press the MENU button.

OSD H-POSITION

OSD V-POSITION
SCALING 0
LANGUAGE

INPUT-1 ANALOG
1280x1024 V:60Hz H:64.0kHz

even if menu options can be selected, the display
may not change.

1024 pixels, the display is enlarged to cover the
whole screen (i.e. The side ratio of the display may
change).

The Language Selection Menu will be displayed
on the screen

Language Selection Menu will disappear.

13

Adjusting the screen display (When using a digital signal)

Adjustment can be made using On Screen Display
(OSD) Menu provided.

On Screen Display for adjustment

This chapter provides the procedure how to adjust
the screen by using operation Pattern.

How to adjust

1.Press the MENU button.
The COLOR Menu will be displayed.

COLOR

Note:

- Like when making an analog connection, the

- The OSD Menu automatically disappears

9300 6500 5000 USER

CONTRAST
R-CONTRAST
G-CONTRAST
B-CONTRAST

INPUT-1 ANALOG
1280x1024 V:60Hz H:64.0kHz

6500

At this point relevant menu options can be adjusted.
Each time MENU button is pressed the next menu

is selected. (COLOR MODE SELECT OSD
Menu disappears)

SCREEN Menu and the GAIN CONTRAL Menu
are displayed. However, you don’t need to adjust
these items.

approximately 30 seconds after the last command.

COLOR Menu

COLOR

9300 5000 USER

CONTRAST
R-CONTRAST
G-CONTRAST
B-CONTRAST

INPUT-1 ANALOG
1280x1024 V:60Hz H:64.0kHz

6500

Notes:

- Use the efbuttons to select [9300], [6500], [5000]

or [USER].

- Selecting [USER] will display the setting values for
[R-CONTRAST], [G-CONTRAST] and
[B-CONTRAST], in order to make fine
adjustments.

- Use the d / MODE button to select
[R-CONTRAST], [G-CONTRAST] and
[B-CONTRAST].

- To go to the next menu: MENU button

9300……Color tone bluer than standard
6500……Color tone standard setting
5000……Color tone redder than standard

USER

R-CONTRAST..…e button for blue-green

f button for red

G-CONTRAST..…e button for purple

f button for green

B-CONTRAST..…e button for yellow

f button for blue

14

Adjusting the screen display (When using a digital signal)

MODE SELECT Menu

MODE SELECT

OSD H-POSITION

OSD V-POSITION
SCALING 0
LANGUAGE

INPUT-1 ANALOG
1280x1024 V:60Hz H:64.0kHz

Notes：

- To choose a menu option: d / MODE button

- To complete adjustment：MENU button

OSD H-POSITION (OSD horizontal position)

The position of the OSD Menu can be moved up and
down. (efbuttons )

OSD V-POSITION (OSD vertical position)
The position of the OSD Menu can be moved up and

down. (efbuttons )

SCALING (Level of scaling)

The sharpness of the image can be adjusted.
(efbuttons )

Note：

- When the display mode is set to less than 1280 ×

1024 pixels, the display is enlarged to cover the
whole screen (i.e. The side ratio of the display may
change).

LANGUAGE

You can choose the language used in OSD Menu.

1. Press the fbutton.

The Language Selection Menu will be displayed
on the screen.

2. Use the d / MODE button to choose a language.

3. Press the MENU button.
Language Selection Menu will disappear.

15

Monitor care and repair

Monitor care

Always remove the plug from the AC outlet when
cleaning the monitor.

Cabinet and control panel section

Use a soft dry cloth to lightly wipe away any grime
from the cabinet and control panel.

If they are very dirty, apply neutral detergent to a
dampened soft cloth, wring it out well and wipe
away grime.

LCD panel section

Use a soft dry cloth to lightly wipe away dirt and
dust from the surface of the LCD panel. (A soft cloth
such as gauze or that used for lens cleaning is
suitable.)

CAUTION!

- Never use thinner, benzine, alcohol, glass cleaner,

etc, as this could lead to color change or change in
shape.

- Never scratch the monitor with anything hard or

apply strong pressure as this could leave marks or
result in malfunction

Storage

If the monitor will not be used for a long period of
time, be sure to remove the power plug from the AC
outlet.

CAUTION!

- Do not leave the monitor in contact with rubber or

plastic items for long periods of times as this could
lead to color change or change in shape.

Troubleshooting

If you think the monitor may be faulty, please check
the following points before taking it to be repaired.

If afterwards it still does not work, please contact the
shop where you purchased the monitor.

The monitor's florescent tubes have a limited life
span.

- If the screen darkens, persistently flickers or does
not light up, it may be necessary to replace the
florescent tube unit. Please inquire at the shop
where you purchased the monitor

- In the initial period of use, due to the characteristics
of florescent tubes the screen may flicker. (This is
not a malfunction.) Should this happen, check by
first turning off the power, then turning it on again.

No image appears on the monitor (Power LED not
lit)

- Is the power cord connected properly? (P6)

No image appears on the monitor (Power LED is
lit)

- Is the computer connected properly? (P5)

- Is the computer turned on?

- Is the signal's input terminal switched to the correct

one? (P7)

- Does the computer's signal timing correspond to

monitor specifications? (P18)

- Is the computer in power-saving mode?

The image appears distorted

- Does the computer's signal timing correspond to

monitor specifications? (P18)

- If you are using the analog signal, perform

automatic screen adjustment. (P10)

- If you can change the refresh rate on the computer

you are using, change the value to a lower
frequency. (P18)

Control buttons do not work

- Is the adjustment lock on? (P8)

16

Specifications

Product specifications

Model name

L17HCN 00ABA
L17HMN 00ABA

LCD display

43 cm measured diagonally TFT LCD module

Resolution (max.)

SXGA 1280 × 1024 pixels

Displayable colors (max.)

Approx. 16.2 million colors (6 bit + FRC)

Brightness (max.)

250 cd/m

Dot pitch

0.264(H) × 0.264 (V) mm

Contrast ratio

430：1

Angle of visibility

Left-right 170° ; up-down 150°
(contrast ration≧5)

Screen display size

Horizontal 337.92 mm × 270.34 mm

Video signal

Analog: Analog RGB (0.7 Vp-p) [75Ω]
Digital：DVI standard based on 1.0

Sync signal

Separate SYNC (TTL level：+/-), Sync on Green,
Composite Sync (TTL level：+/-)

Expansion compensation

Digital scaling (Enlarges VGA/SVGA/XGA etc.
to full screen size.)

Plug & Play

VESA DDC2B compatible

Power management

VESA：based on DPMS
DVI：based on DMPM

Speaker output

1W＋1W

Input signal terminal

Analog：15pin mini D-sub ( 3 rows )

Digital/Analog：DVI-I 29 pin

Screen tilt

Upward approx. 0 - 20°；downward approx. 0 - 5°

Screen swivel

Approx. 90° from left through right (Turn table
type)

Power supply

AC100 – 240 V, 50/60 Hz

Temperature of operating environment

5 - 35°C

2

Power consumption

[L17HCN 00ABA]

33W(with no audio input)
(36W maximum, 1.6W when in power-saving

mode)

[L17HMN 00ABA]

35W (with no audio input)
(38W maximum, 1.6W when in power-saving

mode)

Dimensions

Approx. 381(W)×222(D)×365 – 412(H) mm

Weight

Approx. 6.3 kg (approx. 4.1 kg excluding stand)
(Excluding signal cable.)

Dimensions

- Analog signal cable: approx. 1.8 m

- Audio cable: approx. 1.8m

[L17HMN 00ABA]

- Digital signal cable: approx. 1.8 m

(Units: mm)

17

Specifications

Relevant signal timings

Display mode Hsync Vsync Dot

frequency

VESA

US text 720×400 31.5kHz 70Hz 28.3MHz
Power

Macintosh
series

Sun Ultra
series

- Recommended resolution is 1280×1024.

- All are compliant only with non-interlaced.

- Frequency for Power Macintosh and the Sun Ultra
series are reference values. To connect, another
adapter (commercially available) may be required.

- If the monitor is receiving timing signals that are
not compatible, [OUT OF TIMING] will appear.

Follow your computer's instruction manual to set
the timing so that it is compatible with the monitor.

- If the monitor is not receiving any signal (synch
signal), [NO SIGNAL] will appear.

640×480

800×600

1024×768

1152×864 67.5kHz 75Hz 108.0MHz
1280×960 60.0kHz 60Hz 108.0MHz
1280×1024

640×480 35.0kHz 66.7Hz 30.2MHz
832×624 49.7kHz 74.6Hz 57.3MHz
1024×768 60.2kHz 75Hz 80.0MHz
1152×870 68.7kHz 75Hz 100.0MHz
1280×1024

1024×768

1280×1024

31.5kHz 60Hz 25.175MHz

37.9kHz 72Hz 31.5MHz

37.5kHz 75Hz 31.5MHz

35.1kHz 56Hz 36.0MHz

37.9kHz 60Hz 40.0MHz

48.1kHz 72Hz 50.0MHz

46.9kHz 75Hz 49.5MHz

48.4kHz 60Hz 65.0MHz

56.5kHz 70Hz 75.0MHz

60.0kHz 75Hz 78.75MHz

64.0kHz 60Hz 108.0MHz

80.0kHz 75Hz 135.0MHz

64.0kHz 60Hz 108.0MHz

80.0kHz 75Hz 135.0MHz

48.3kHz 60Hz 64.13MHz

53.6kHz 66Hz 70.4MHz

56.6kHz 70Hz 74.25MHz

61.8kHz 66Hz 94.88MHz 1152×900

71.8kHz 76.2Hz 108.23MHz

71.7kHz 67.2Hz 117.01MHz

81.1kHz 76Hz 134.99MHz

Relevant signal timings (digital)

Display mode Hsync Vsync Dot

frequency

VESA

US text 720×400 31.5kHz 70Hz 28.3MHz

- Recommended resolution is 1280×1024.

- All are compliant only with non-interlaced.

- A computer with an output terminal conforming to
DVI (DVI-D24 pin or DVI-I29 pin) and with
SXGA output capability can be connected here.

(Depending on the type of computer to be
connected, the display may not work correctly.)

- If the monitor is receiving timing signal that are not
compatible, [OUT OF TIMING] will appear.

Follow your computer's instruction manual to set
the timing so that it is compatible with the monitor.

- If the monitor is not receiving any signal (synch
signal), [NO SIGNAL] will appear.

640×480

800×600

1024×768

1152×864 67.5kHz 75Hz 108.0MHz
1280×960 60.0kHz 60Hz 108.0MHz
1280×1024 64.0kHz 60Hz 108.0MHz

31.5kHz 60Hz 25.175MHz

37.9kHz 72Hz 31.5MHz

37.5kHz 75Hz 31.5MHz

37.9kHz 60Hz 40.0MHz

48.1kHz 72Hz 50.0MHz

46.9kHz 75Hz 49.5MHz

48.4kHz 60Hz 65.0MHz

56.5kHz 70Hz 75.0MHz

60.0kHz 75Hz 78.75MHz

18

The analog RGB input connector pin

(Mini D-sub connector with 15 pins)

No. Function

1 Red video signal input
2 Green video signal input
3 Blue video signal input
4 GND
5 GND
6 For red video signal GND
7 For green video signal GND
8 For blue video signal GND
9 +5V

10 GND

11 N.C.
12 DDC data
13 For Hsync signal input
14 For Vsync signal input
15 DDC clock

The DVI-I input connector pin [L17HMN
00ABA]

(DVI-I connector with 29 pins)

Specifications

Power management

The monitor is based on the VESA DPMS and the
DVI DMPM standards.

To activate the monitor's Power Management
Function, both the video card and the computer must
conform to the VESA DPMS standard and the DVI
DMPM standard.

DPMS：Display Power Management Signaling

DPMS

mode

ON Display on

STANDBY No Yes

SUSPEND Yes No

OFF

DMPM：Digital Monitor Power Management

DPMS mode Screen

ON Display on 38W

OFF Display off 1.6W

DDC (Plug & Play)

This monitor supports the VESA DDC (Display Data
Channel) standard.

DDC is a signal standard for carrying out Plug &
Play function on the monitor or PC. It transfers
information such as degree of resolution between the
monitor and PC. You can use this function if your PC
is DDC compliant and if it is set so that it can detect
the Plug & Play monitor

There are many varieties of DDC due to the
difference between systems. This monitor works with
DDC2B.

Screen

Display off 1.6W

Power

consumption

36W*

38W**

Power

consumption

H-sync V-sync

Yes Ye s

No No

19

Instructions for attaching a VESA compliant arm

An arm or stand based on the VESA standard
(commercially available) can be attached to the
monitor.

Procurement of the arm or stand is at the customer's
discretion.

Arms or stands able to be used

Attachment must satisfy the following.

- Compatible with the VESA standard.

- Have a gap of 100 mm × 100 mm between the

screw holes on the section to be attached.

- Note be likely to fall off or break off after being
attached to the monitor.

How to attach the arm or stand

- Be careful not to overly bend the cable or add

extension cords as this could lead to malfunction.

- While following these instructions, please also refer

to the installation instructions in the operation
manual included with the arm or stand.

5. Remove the six screws and then remove the stand
from the monitor.

Note：

- The stand is specially made for use with this

monitor. Once having removed the stand, never
attempt to another device.

- Once having removed the screws, store them

together with the stand and if the stand is ever
re-attached be sure to use the original screws.

Using different screws could lead to a malfunction.

6. Attach the arm to the monitor with the four screws.

CAUTION!

- Be careful not to get your fingers pinched between
the display and stand nor to let the stand drop.
These could lead to injury.

1. Remove the cables.

2. Spread out a soft cloth on a suitable horizontal

surface.

3. Being careful not to damage the monitor, gently

lay the monitor on it display-side down.

4. Remove the cover.

- While pressing the U areas on the sides, push

it up.

Note：

- The screws used to attach the arm should be M4
screws with a length of 6 mm ~ 8 mm protruding
from the surface to be attached. Using different
screws could cause the monitor to fall off or to be
internally damaged.

U

20