Prince Castle 740-T44N Parts List

OPERATING

This product is warranted to be free from defects in material
and/or workmanship for a period of 1 year from date of original
installation, not to exceed 18 months from the date of
manufacture.

Any component which proves to be faulty in material and/or
workmanship will be replaced or repaired (at the option of
Prince Castle, Inc.) without cost to the customer for parts and
labor. This equipment is portable; charges for on-location
service (e.g., trip charges, mileage) are not included in the
provisions of this warranty.

This warranty is subject to the following exceptions/conditions:

• Use of any non-genuine Prince Castle parts voids this
warranty.

• All labor to be performed during regular work hours.
Overtime premium (the incremental amount) will be charged
to the customer.

• Damage caused by carelessness, neglect and/or abuse
(e.g., dropping, tampering or altering parts, equipment
damaged in shipment, by fire, flood or an act of God) is not
covered under this warranty.

• All problems due to operation at voltages other than that
specified on equipment nameplates are not covered by this
warranty. Conversion to correct voltage is the customer’s
responsibility.

• This equipment must be serviced by Prince Castle
Authorized Service Agency or a Prince Castle Service
Technician during the warranty period.

LIMITED WARRANTY

INSTRUCTIONS

Slow Cook/Hold Timers
Model No. 740-T44N &
740-T66N

Model Description

740-T44N Four Channel

740-T66N Six Channel

ELECTRICAL

TABLE OF CONTENTS

Installation..................................................................... 2

Programming................................................................. 2

Operation ....................................................................... 3

Cleaning ........................................................................ 4

Parts List....................................................................... 4

Exploded View .............................................................. 5

Troubleshooting ............................................................ 5

Wiring Diagrams ........................................................... 6

PAGE

740-T Series

120 Volts
50-60 Hz

740-529revA

355 East Kehoe Blvd. l Carol Stream, IL 60188

Tel: [phone] l Fax: [phone]

Toll Free: 1-800-PCASTLE

Printed in USA 3/06 © 2006

INSTALLATION

1. After you have removed the timer from the carton,
inspect the unit for signs of damage. If there is
damage to the unit:

z Notify carrier within 24 hours after delivery.

z Save carton and packing materials for inspection

purposes.

z Contact your local dealer or, if purchased di-

rectly, the Prince Castle Customer Sales Depart­ment at 1-800-722-7853 to arrange for a replace­ment to be sent.

2. Verify that all parts have been received. Mounting

Brackets and hardware provided.

3. To mount the timer, place mounting brackets in de­sired location. Scribe location of mounting holes,
center punch, and drill holes. Attach timer to mount­ing brackets placing star washer between bracket and
timer.

PRINCE

CASTLE

Logo

The timer currently supports 3 program stages or
functions. Each program stage is independently
programmed. The stages run in succession begin­ning with stage #1 and ending with stage #3. After
each stage, the timer sounds an alarm and flashes
“End”. Each stage has a time and LED color. The
factory-default times, stage color, and alarm modes
are described in Table 2.

Note: Some stage modes are not available (N/A) for
all stages and the alarm beat and pitch is not
programmable.

Below Are The Pre-Set Stages Per Nathan’s specifi­cations

Stage Time Color Alarm Pitch Alarm Beat

1 3:00 Green Low Slow
2 0 Yellow High Slow
3 3:00 Red High Fast

Activates Program Mode and used to
adjust the alarm sound level.

DISPLAYS AND INDICATORS

TIME

Display

H:M

M:S

LED

Indicators

CONTROLS

Channel

(Button)

SCAN/UP

ARROW

SCAN/DOWN

ARROW

Printed in USA 3/06 © 2006

Shows the time for the selected channel
number.

Indicates the time value is in Hours and
Minutes.

Indicates that the time value is in
Minutes and Seconds.

Located above each channel timer
button, these lights change color
depending on the stage of the count­down. Green = Stage 1, Yellow =
Stage 2 Red = Stage 3.

Activates countdown sequence in the
run mode.

In the program mode, it increases time
values for each channel . In the Run
Mode, it is used in conjunction with logo
button to increase the volume.

In the program mode, it decreases time
values for each channel . In the run
mode, it is used in conjunction with logo
button to decrease the volume.

PROGRAMMING

1. Press and hold the PRINCE CASTLE logo for six
seconds. The TIME displays will change from

“----” to “Prog” and a beep will sound.

Prog

Prog

Prog

Prog

Prog

Prog

IMPORTANT: If a channel is not pressed within 30

seconds the display will change back to
“- - : - -” and the timer will automatically
go back to the run mode.

NOTE: While all displays are showing “Prog”, press-

ing the UP or DOWN ARROW Button will
increase or decrease, respectively, the display
intensity level.

2

740-529revA