Prince Castle 101-KL Operators Manual

OPERATING

INSTRUCTIONS

Portion All Dispenser
Model No. 101-K &101-KL

TABLE OF CONTENTS PAGE

Installation..................................................................... 2

Operating....................................................................... 2

Cleaning ........................................................................ 3

Exploded View & Parts List ........................................ 3

LIMITED WARRANTY

This product is warranted to be free from defects in
material and/or workmanship for a period of one (1)
years from date of original installation, not to ex­ceed 18 months from date of shipment from our
factory with the exception of the rubber parts.

Prince Castle Portion-All® Dispensers distribute
ketchup and other condiments quickly, easily, and
evenly . Our carefully calibrated lever sets control
portions of 1/5 oz. (5.6g), 1/3 oz. (9.4g), 2/5 oz.
(1 1.3g), or 2/3 oz. (18.9g).

PRODUCT SPECIFICATION

Model Length Height

101-K 12-5/8” (32.0cm) 7-5/8” (19.3cm)

Width Shipping Wgt.

6-45/64” (17.1cm) 4lbs. (1.81kg)

Model Length Height

101-KL 12-5/8” (32.0cm) 8-3/4” (22.2cm)

Width Shipping Wgt.

6-45/64” (17.1cm) 5lbs. (2.2kg)

Any component which proves to be faulty in material
and/or workmanship will be replaced or repaired (at
the option of Prince Castle, Inc.) without cost to the
customer for parts or labor.

This warranty is subject to the following exceptions/
conditions:

l This equipment is portable; charges for on-loca-

tion service (e.g., trip charges, mileage) are not
included in the provisions of this warranty.

l Damage caused by carelessness, neglect, and/

or abuse (e.g., dropping, tampering or altering
parts), equipment damaged in shipment, by fire,
flood or an act of God is not covered under this
warranty.

Printed in 2001
Prince Castle Inc. REV. A

355 East Kehoe Blvd. l Carol Stream, IL 60188

Tel: [phone] l Fax: [phone]

Toll Free: 1-800-PCASTLE

101-524

INSTALLATION

6. Insert assembled plunger rod and plunger into the
container. See Figure 3.

1. After you have removed the Dispenser from the
carton, inspect the unit for signs of damage. If there
is damage to the unit:

l Notify carrier within 24 hours after delivery.
l Save carton and packing materials for inspection

purposes.

l Contact your local Prince Castle dealer or, if

purchased directly, the Prince Castle Customer
Sales Department at 1-630-462-8800 to arrange
for a replacement to be sent.

2. Verify that all parts have been received:

l Rubber Parts
l Lever and Plunger Rod

3. Wash all parts before using.

4. Moisten the diffuser with water to allow for better
flexibility. Squeeze the sides of the diffuser until it
is bent into an oval shape. Place the crease in
edge of the diffuser along the metal rim of the
opening in the bottom of the conveyor. Continue to
press the diffuser into the conveyor all around the
edges, making sure the diffuser is secured into
place. See Figure 1.

Figure 3

7. Assemble the plunger rod and lever. Slide the lever
through the lever stop, then guide the plunger rod
into the desired hole. Push down against the spring
of the plunger, then guide the end of the lever into
the tee slot of the container. See Figure 4.

Figure 4

OPERATION

Figure 1

5. Assemble retainer, flapper valve and plunger. Then,
press the plunger rod into the retainer assembly.
See Figure 2.

Figure 2

Plunger Rod

Plunger

Flapper Valve

1. Determine the amount of product to be dispensed.
The Portion-All® dispenser is designed to deliver
between approximately 1/5 - 2/3 oz. of product,
depending on the lever hole position and type of
condiment being dispensed. See Figure 5.

Lever Hole Position Amount Dispensed

1..........................................1/5oz. (5.6g)

2..........................................1/3oz. (9.4g)

3..........................................2/5oz. (11.3g)

4..........................................2/3oz. (18.9g)

Figure 5

1

23

4

Retainer

Hole Positions

2