PrimeCables Cab-CD304-2L Operator's Manual

T O O L S

MODEL:

20V

Cab-CD304-2L

20V CORDLESS DRILL 2 SPEED

Operator’s Manual

SAVE THIS MANUAL

You will need this manual for safety instructions, operating procedures and warranty.

Put it and the original sales receipt in a safe dry place for future reference.

IMPORTANT SAFETY INSTRUCTIONS

WARNING When using electric tools, machines or equipment, basic safety

precautions should always be followed to reduce the risk of fire, electric shock,

and personal injury.

READ

1. KEEP THE WORK AREA CLEAN. Clean areas prevent injuries.

2. CONSIDER THE WORK AREA ENVIRONMENT. Don’t use power tools in damp,
wet, or poorly lit locations. Don’t expose your tool to the rain. Keep the work area

well lit. Don’t use tools in the presence of flammable gases or liquids.

3. KEEP CHILDREN AWAY. All children should be kept away from the work area.
Don’t let them handle machines, tools, or extension cords.

4. STORE UNUSED EQUIPMENT. Store equipment in a dry area to inhibit rust.
Equipment also should be stored in a high location or locked up to keep out of the reach
of children.

5. DON’T FORCE THE DRILL. It will do the job better and more safely at the rate
for which it was intended.

6. USE THE RIGHT TOOL. Don’t force a small tool or attachment to do the work

of a larger industrial tool. Don’t use a tool for a purpose for which it was not

intended.

7. DRESS PROPERLY. Don’t wear loose clothing or jewelry. They can get caught
in the moving parts. Protective, non-electrically conductive gloves and non-skid

footwear are recommended when working. Wear protective hair covering to
contain long hair.

8. USE EYE PROTECTION. Use a full face mask if the work you’re doing produc­es metal filings, dust or wood chips. Goggles are acceptable in other situations.

Wear a clean dust mask if the work involves creating a lot of fine or coarse
dust.

9. DO NOT TOUCH THE BIT WITH HANDS AFTER DRILLING. Drill bits can become

extremely hot during your job.

10. SECURE WORK. Use clamps or a vise to hold the work if possible. It’s safer
than using your hands and it frees both hands to operate the tool.

11. DON’T OVERREACH. Keep proper footing and balance at all times. Do not
reach over or across machines which are running.

12. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating and changing accessories.

For safe performance, keep handles dry, clean and free from oil and grease.

13. REMOVE ADJUSTING KEYS AND WRENCHES. Although your

cordless drill has a convenient keyless chuck, make it a habit to check that
keys and adjusting wrenches are removed from any rotating tool before using.

14. AVOID UNINTENTIONAL STARTING. Don’t carry the tool with a finger on the
switch. Be sure the direction switch is in the NEUTRAL position when not in

use or when changing bits.

15. STAY ALERT. Watch what you are doing & use common sense. Don’t operate
any tool when you are tired.

16. CHECK FOR DAMAGED PARTS. Before using the drill, any part that is dam-

aged should be carefully checked to determine that it will operate properly and
perform its intended function. Check for the alignment of moving parts, binding
of moving parts, breakage of parts, mountings, and other conditions that may
affect its operation. Check the bits to make sure they are sharp and not chipped.
Inspect screws and tighten any ones that are loose. Any part that is damaged
should be properly repaired or replaced by an authorized service center un-

less otherwise indicated elsewhere in the instruction manual. Have defective
switches replaced by an authorized service center. Don’t use the tool if the
switch does not turn on and off properly.

17. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded

surfaces: pipes, radiators, ranges, and refrigerator enclosures. When drilling
into walls, floors, or wherever “live” electrical wires may be encountered, try to
ascertain whether there is a danger of shock. Even so, DO NOT TOUCH THE
CHUCK OR ANY FRONT METAL PARTS OF THE DRILL. Hold the tool only by
the plastic handle or the side grip to prevent electric shock in case you hit a live

wire.

18. REPLACEMENT PARTS. When servicing, use only identical replacement
parts.

INSTRUCTIONS BEFORE USING THIS TOOL

ALL

!

2

PRECAUTIONS FOR B

ATTE

AND CHARGER

RY

!

!

CHARGE B

CHARGE

1.
than 32°F and lower than 104°F.

2. DO NOT CHARGE IF THE CHARGER’S CORD OR PLUG IS DAMAGED.

Charg
charger is damaged in any way, have it repaired by a qualified serviceman.

3. USE WITH CAUTION, when coming into contact with items that can cause
an electrical short,

DO NOT INCINER

4.

This product has been carefully engineered and manufactured to give you
dependable operation. Please read this manual thoroughly before operating your
new product, as it co
features and obtain the performance that will bring you continued use for many

years.

WARNING! The warnings, cautions, and instructions detailed in this manual cannot

co
USE COMMON SENSE AND CAUTION WHEN OPERATING THE TOOL.

r

e

v

A

TTE

R

Y

A

T ROOM TEMPER

A

damaged cord may result in

ing with

l

a

a

ntains the information you need to become familiar with its

cond

e

l

b

si

s

o

p

l

T LEAST 6 HOURS

TURE.

A

such as paper clips, nails, the sides of a metal tool box.

TTE

A

B

THE

TE

A

d

n

a

s

n

o

i

t

i

before initial use.

The

Y

R

s

n

o

i

t

a

u

t

i

s

room temperature must be higher

fire or electrical shock.

a

.

r

u

c

c

o

t

a

h

t

If the

SAFETY PRECAUTIONS FOR DRILL

Wear ear protectors when impact drilling. Exposure to noise can cause hearing

■

loss.

!

■

Hold power tool by insulated gripping surfaces, when performing an operation

where the cutting accessory may contact hidden wiring.

Special Safety Instructions for Battery pack and Charger

■
If under extreme conditions any electrolyte should escape from the battery, it's

essential to avoid contact with skin. If electrolyte does come into contact with your

skin, rinse it off with water. In the event of electrolyte contact with your eyes, it's

essential to consult a doctor.

a) Before the use of the charger and the battery pack, read the instruction

manual for it carefully.

b) During the charge process, the current used should correspond to the current of
the battery charger.
c) Never let moisture, rain or splashed water reach the charging location.
d) The ambient temperature must not exceed 40

o

C.

3

SAFETY PRECAUTIONS FOR DRILL

e) Battery pack, which are defective or damaged or can no longer
be recharged, must be disposed of as hazardous waste. Hand them over at a
special collection point. Never harm our environment. Do not throw unusable
battery pack away into the domestic waste, into fire or into water.
f) If the electrical cable is damaged, the wire may only be replaced by the
supplier or by his repair workshop. Have repairs carried out only by an
authorized specialist.
g) Use only battery pack, which have been produced by the
original manufacturer.
h) Always keep the surface of the charger free from dust and dirt.
i) Insert the battery pack into the charger. Follow the guidelines provided
concerning polarity.
j) Always remove battery pack before working on the machine
k) When the battery pack is outside the drill, cover the contacts to avoid
short circuits (e.g. from tools)
l) Do not throw Li-ion batteries into water or fire, risk of explosion!
m) Protect the battery pack from impacts, and don't open it.
n) Never discharge the battery pack completely and recharge occasionally
if not used for a prolonged period.

CRIPTION

SPECIFICATIONS

■ 20V DC

■ No load speed: 0-350/0-1250 RPM

■ Chuck: 10mm

■ Clutch: 20+1 Torque settings

■ Charge time: 3-5 hours

FUNCTION

1. Keyless chuck

2. Torque Settings

3. Variable speed trigger switch

4. Left/Right switch

5. Handle

6. Battery pack

7. 2 Speed Selector Switch

7

1

2

3

4

4

5

6

OPERATING PROCEDURES

ADJUSTMENTS

Initial operation

• Insert battery pack into the bottom of the handle ( until click )

• Remove the battery pack by pressing the release button on
the battery,and pulling the battery pack out.

Charging

NOTE: This Lithium-Ion battery pack is shipped partially charged. Fully charge the

battery pack before using it for the first time.
A fully discharged battery pack will charge in about 3-5 hours at a temperature
between 32 °F (0° C) and 104°F (40°C).

• Put the battery pack in the charger stand. Make sure it is placed correctly (+ and -)

• The battery charger consists of two parts.

1. A AC/DC adaptor.

2. A charging stand.

• Insert the AC/DC adaptor into household current receptacle. The green light is on.
The green light is the power indicator.

• Properly insert the battery pack into the charge stand. Make sure it is placed
correctly(+ and -). The red light is on. The red light is the charge indicator.

• Normal charging time is 3-5 hours. When the battery is fully charge, the red light
will turn off.

• When charging more than one battery pack in succession, allow 15 minutes
between charges.

Caution

• Fully charge battery before first use. The battery will reach full capacity after
being charged and discharged several times

• Avoid short periods of charging. Only charge battery pack when fully empty.

• Adaptor, charger and battery pack will be warm when charging.

Inserting drill bits / screwdriver bits

• To insert a drill bit / screwdriver bit, hold the back section of the chuck and rotate
the front section of the chuck

• Insert the drill bit / screwdriver bit into the chuck ( as far as possible )

• For screwdriver bits use an adaptor

• Select the correct screwdriver bit to avoid damaging the screw

• Firmly tighten the chuck by hand and check if the drill bit / screwdriver bit is
seated firmly in the chuck

1. Front section of chuck

2. Back section of chuck

5