Primax Electronics M7B601 User Manual

Visit our website at:
www.mogomouse.com
Features and specifications are
subject to change without notice.
2006 Newton Peripherals, LLC
MG-100-01-0002-01 rev 2

Bluetooth Laptop Mouse

Installation Guide

Use it

like your wireless

desktop mouse

Store It

inside a

PC card slot

Charge it

automatically

Newton Peripherals MoGo Mouse

BT

Introduction

Congratulations on your purchase of a MoGo MouseBT.

This user’s guide describes how to connect and use the
MoGo MouseBTto your Laptop.

In addition to this user’s guide this package contains:

• Newton Peripherals MoGo Mouse

BT

System Requirements

To use the MoGo MouseBT, your computer must meet
the following requirements:

Hardware

• Type II PC card slot

• USB Bluetooth adaptor or embedded Bluetooth

Operating System

• Bluetooth®-enabled Windows®98, Me, 2000, or XP.

• Bluetooth

®

-enabled Macintosh®running Mac®OS 10.2.8 or later.

Charging and Storing

The MoGo MouseBTis equipped with an internal
rechargeable battery. It is recommended that
before using, you insert the MoGo Mouse

BT

inside your type II PC card slot for charging.
The MoGo MouseBTautomatically begins
to charge when installed. The laptop must
be turned on for charging to take place.
You should allow up to 60 minutes
for initial charging of MoGo Mouse

BT

.
Charging status is indicated by either
a red light for active charging or a
green light for fully charged.

GREEN = CHARGED

RED = CHARGING

Battery LED Status

What to do if the “Found new Hardware Wizard” appears

When inserting the MoGo MouseBTin your computer’s PCMCIA slot for the
first time, the window below may appear. Though no software is required
for the MoGo MouseBTto charge properly, Microsoft Windows will try to load
a driver for the MoGo Mouse

BT

. To stop Microsoft Windows from displaying
this window follow the steps below. Once completed no other action is
required for setting up your laptop for charging.

You may see a message appear warning you that the driver was not
installed and your device my not work properly. You can ignore this
as the MoGo Mouse

BT

does not need a driver to operate properly.

Pairing your MoGo MouseBTwith your laptop

Bluetooth devices require that you initially “pair” your

MoGo MouseBTwith your laptop. Follow the steps

below to prepare your MoGo Mouse

BT

for pairing.

Once paired to your laptop the MoGo MouseBTonly

needs to be turned on for operation with your laptop.

1. Turn on the MoGo MouseBTby opening kickstand on

side of unit with finger. You may notice a one time RED blink

from Optical Sensor on the bottom of the mouse.

2. Press the “connect” button down until the status light starts

flashing blue, every 2 seconds. Your MoGo MouseBTis now ready

to pair to your laptop. It will stay in this state for 3 minutes.

3. Initiate your laptop Bluetooth to complete pairing your mouse. In case
you are requested to enter a Pass Code or PIN number, simply enter
“0000”. MoGo MouseBTdoes not require such a code to operate. Refer to
the owner’s manual for specific instructions on pairing your laptop Bluetooth.

Check the box to install

automatically and click “Next”.

Check the box at the bottom

(Don’t Prompt me again to install

the software) and click finish.

Once connected the blue light on the MoGo MouseBTwill begin to blink
slowly, every 3 seconds.

4. You are ready to MoGo!

Pairing Your MoGo MouseBTwith another Laptop

Your MoGo MouseBTcan only be paired with one laptop at a time. Pressing
the connect button will break the current pairing and prepare the MoGo

Mouse

BT

to be paired with another laptop.

Using your MoGo Mouse

BT

Since the MoGo MouseBTfits into the Type II PC card slot to store and charge,
it needs a kickstand to prop up the back of the mouse to make it functional
and ergonomic. To turn it on, open the kickstand from the side. Click the right
or left button to activate the connection. Note: initially, you must pair the
MoGo Mouse

BT

to the laptop before this can occur.

Turning the MoGo MouseBToff is simple. Collapse/close the kickstand and
MoGo MouseBTwill automatically turn off.

Leaving the MoGo Mouse

BT

untouched for ten minutes will cause the mouse
to fall asleep. Wake it by simply pressing the right or left button. Note: The
MoGo Mouse is designed so that leaving it in sleep mode reduces battery use
to save battery power.

If the laptop Bluetooth signal becomes unavailable to the mouse, this will
also cause the mouse to fall asleep.

If the indicator LED turns solid red, the battery is very low and needs
to be recharged.

Operating Hints

For optimal performance and RF reception:

• Avoid using the MoGo MouseBTon a metal surface. Metals, such as iron,

aluminum or copper, shield the Bluetooth transmission and may slow
down the MoGo Mouse

BT

’s response time or cause the MoGo MouseBTto

fail temporarily.

• The MoGo MouseBTwill enter a suspend mode at the same time your

computer does. To activate the MoGo Mouse

BT

, press any button on

your MoGo MouseBT.

•If your computer has a metal case that contains aluminum or magnesium,

use the MoGo MouseBTto the side. The display panel may interfere with
the Bluetooth signal if you use the MoGo MouseBTdirectly in front
of the computer.

•Glass or mirrored surfaces can result in erratic behavior for all mice

using optical technology.

•To maximize battery life, use the MoGo Mouse

BT

on a white, or light
colored surface. Dark surfaces cause the MoGo MouseBT’s light emitting
diode (LED) light to glow brighter, which causes the battery to discharge

more rapidly.

Specifications

Troubleshooting

The MoGo MouseBTis not working.

•Make sure that the MoGo MouseBTis charged. Install into type II PC
card slot and wait for Green LED indicator.

• Verify that Bluetooth is configured correctly on your computer

1) Click Start/Settings/Control Panel/System/Hardware/Device Manager.

2) Check under ‘Bluetooth Devices’ that a ‘Newton Peripherals MoGo

Mouse

BT

’ is installed.

I cannot connect to a paired device.

• Paired Bluetooth devices are displayed in a connection management
window of your Bluetooth management application, even if the remote
device is out of range or not powered up.

•Verify that the remote member of the pair is within Bluetooth range,
and powered up, and then attempt the connection again.

Bluetooth Specification
Resolution
Working range
RF transmit power Operating
Battery Voltage
Operating Current
Standby Current
Sleep Mode Current
Dimensions

Weight

1.1 and 1.2 compliant
500 DPI
Up to 30 feet (10 m)
<4 dBm

4.2 V
165 mAh Internal Rechargeable
32 mA
22 mA
.04 mA

3.4 x 2.125” x .21 inches
(86 x 54 x 5 mm)

1.5 oz or 41 grams

I cannot discover Bluetooth services on an un-paired remote device.

• The remote device may not be powered up or may be out of range.

• Verify that the remote device is powered up.

• Verify that the remote device is in Connectable mode
(Bluetooth Configuration Panel > Accessibility tab).

• Perform a Search for Devices to verify that the device is within range.

For technical questions, please visit:

North America Email: [e-mail]
EMEA Email: [e-mail]

ASIA Email: [e-mail]

Product Registration

Newton Peripherals recommends that you register your Newton Peripherals
accessory shortly after purchasing it. To register your Newton Peripherals
accessory, go to: http://www.Newtonperipherals.com/registration/

You will need to provide your full name, email address, phone number,
date purchase, place of purchase and company information (if applicable).

Warranty

Newton Peripherals warrants this product to be free from defects in materials
and workmanship for two years from the date of purchase of the Products.
The warranty extends only to you if you are the end user with original purchase
receipt. We will, at our option, repair or replace the Products that do not
conform to the warranty. We may use functionally equivalent reconditioned/
refurbished/remanufactured/pre-owned or new Products or parts. If your Newton
Peripherals accessory is found to be defective within that time, we will promptly
repair or replace it. This warranty does not cover accidental damage, wear
and tear, or consequential or incidental loss. Under no conditions is Newton
Peripherals liable for loss of, or damage to a computer; nor loss of, or damage
to, programs, records, or data; nor any consequential or incidental damages,
even if Newton Peripherals has been informed of their possibility. This warranty
does not affect your statutory rights.

Regulatory Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interference
that may cause undesired operation.

Ready, set…MoGo!

Easy to stow, ready to go

Patent-pending optics provide
smooth, accurate performance

Integrated “kickstand”

flips out to position

BT

MoGo Mouse

Bluetooth operation

delivers wireless freedom

comfortably

No batteries to replace —
takes just minutes to
recharge inside your laptop

©2006 Newton Peripherals, LLC. All Rights Reserved.

Bluetooth is a registered trademark of Bluetooth SIG.

All other trademarks and registered trademarks are the property

of their respective holders. Patents Pending.