Introduction
Thanks for purchasing PHS-8 Bluetooth Headset. Your Bluetooth Headset is
a stylish headset that enables comfortable handsfree communication with
compatible phone that supports Bluetooth technology.
Functions & Controls
3
1
5
4
1. Multifunction key
Indicator light
Switches the headset on and off
Answer incoming call
End active call
Reject incoming call
2. Charger connector
3. Earpiece
4
. Microphone
5
. Volume up / down buttons
Relays the caller's voice.
For battery charging.
Picks up your voice input.
2
Getting started
Remove all components from the package...
Bluetooth Headset (with 15 mm diameter earbud)
AC Battery Charger
User Guide
Charging the battery
Before using the Bluetooth Headset, you need to charge the built-in
rechargeable battery for approximately 2 hours. The indicator light is
red while charging. When the battery is fully charged, it provides up to 7
hours talking time and up to 170 hours standby time.
1. Connect the AC battery charger cable’s Micro USB connector to Bluetooth
Headset’s Micro USB socket.
2. Plug the charger’s AC plug to AC outlet. When charging, the Bluetooth
Headset’s status indicator lights in solid red.
3. When the battery is fully charged, the status indicator turns to green.
Unplug the charger cable from AC outlet and Bluetooth Headset.
Pairing the Bluetooth headset to a
Bluetooth mobile phone
Pairing is the process for linking the headset with your Bluetooth enabled
mobile phone. After this process is completed, you can use the Bluetooth
Headset with the paired mobile phone. The Bluetooth Headset can be
paired with up to 8 compatible phones but connected to only one phone
at a time. If the headset is turned on with no existing pairing information
stored (e.g., first time use or pairing information been erased), it will enter
pairing mode automatically.
To enter pairing mode manually...
1. The headset must be in off mode.
2. Press the multifunction button for at least 5 seconds. Blue LED light
flashing rapidly, and 4 ascending tones can be heard. Your mobile
phone can now "look for" the headset.
3. Activate the Bluetooth connection with the mobile phone according to
the mobile phone’s user’s guide.
4. Set the mobile phone to search for the Bluetooth devices according to
the mobile phone’s user’s guide.
5. Select the Bluetooth Headset from the phone menu.
6. Enter the pin code 0000 to connect (or “pair”) Bluetooth Headset to the
phone. You will hear two high tones when pairing completed.
7. Select ‘PHS-8’ from the device list on your phone. The LED will light
rapidly every 5 seconds with the headset connected to your phone.
If the headset is turned on within 10 meters from several paired phones,
the headset will try to connect to the last connected device. If the headset
does not connect to the last connected phone, green LED will be flashing
every 5 seconds indicating it is in power on however not engaged status.
If the headset is turned on but not connected established, it will stay in
connectable status for 5 minutes before automatically turn off.
If the headset is dropped off from previous connection, it will stay in
connectable status for 30 minutes before automatically turn off.
Phone list can be erased by holding the multifunction button, then
pressing volume + key 6 times at an interval of 0.5 seconds.
Clear settings or reset
To clear all the pairing settings from the headset, press and hold the
multifunction key, and press Volume + key six times. The indicator light
alternates red, green, and blue twice. After the settings are cleared, the
headset enters the pairing mode for about 5 minutes (the indicator light
flashes blue quickly).
To reset the headset if it stops functioning, although it is charged, plug
the charger into the headset while you press and hold the multifunction
key. The reset does not clear the headset settings.
Operation
To turn on the headset
To switch on, press and hold the multifunction key until the headset
beeps and the indicator light turns on.
To turn off the headset
To switch off, press and hold the multifunction key for at least 4
seconds until the indicator light turns red.
Making a Phone Call
When the headset is connected to the phone, make a call using the
phone in the normal way.
Note: the call functions depending on the phone type you use. Please
refer to the manual of your phone for the related function.
The blue indicator light flashes during the call.
Answering and Ending a Phone Call
When a call comes in, the indicator light flashes quickly, and ringing tones
can be heard through the headset until the call is answered.
You can short press the multifunction key to answer and end the call.
You can also answer and end the call through the mobile phone.
Note: Some phones offer Auto Answer function and may be used with the
headset or speakerphone, but this is a phone dependent feature. Please
refer to the manual of your phone for that function.
Rejecting a Call
Double press multifunction key to reject a incoming call.
Voice dialing (phone dependent)
Press the multifunction key for about 2 to 3 seconds when there is no
call in active to initial voice dialing, and one high tone can be heard.
To terminate voice dialing, press the multifunction key briefly again.
Voice dialing cannot be used during a call
Switching the Call between Phone and Headset
To switch the call from the headset to a connected device, press and hold
the Volume Down key for about 2 seconds, or use the keys of your device.
To switch the call back to the headset, please use the related function key
on the phone (please refer to phone instruction), or press and hold the
Volume Down key on the headset for about 2 seconds.
Redialing the Last Dialed Number
(Phone dependent)
if your device supports last number redialing with the headset, press the
multifunction key twice when no call is in progress
Reconnecting the Paired Bluetooth Headset to a
Compatible Phone
To reconnect the Bluetooth Headset to the last connected phone, proceed
as follows:
1. Press and hold the multifunction key for 3 seconds to turn on the
Bluetooth Headset.
2. Make sure your phone is on and Bluetooth function is enabled.
Please refer to the phone’s user guide and make the connection in
the Bluetooth menu of your phone.
3. The phone should connect to the headset automatically. If not,
please refer to ‘Pairing the Bluetooth Headset with a Compatible
Phone’ section and performance pairing again,
Other status
Status Indicator light
Idle* (power on but
not connected)
Battery low
Charging
Call in active
* The headset will switch off automatically if in idle mode for 30 minutes.
Green flashing once every
5 seconds
Red flashing once every
2.5 seconds
Red solid light
Blue flashing once every
2.5 seconds
Sound
n/a
Three descending
tones
n/a
n/a
Loading...