FullTrap
INSTALLATION MANUAL
Congratulations on purchasing the FullTrap from Primacoustic. The FullTrap is an easy to
assemble bass trap that will effectively absorb a wide bandwidth of frequencies and look
great for many years to come. Please take a few minutes to read through this assembly
manual. It will give you a list of included parts, as well as step by step assembly and wall
mounting instructions. Please refer to www.primacoustic.com/appnotes for various placement
options, benefi ts, and general room acoustics information. Should you have any questions or
comments, we invite you to send an email to: info@primacoustic.com.
48” SIDES
BEVELED WALL
MOUNT
BEVELED CROSS
SUPPORT
CROSS SUPPORT
46” PANEL STOPS
FABRIC COVERED
ACOUSTIC PANEL
LOADED VINYL
23” TOP
23” BOTTOM
TOOLS REQUIRED:
- Medium sized Phillips screwdriver
- 48” Bubble Level and small bullet level
- Wall Stud fi nder (recommended)
- Cordless Drill (recommended for installing drywall
anchors)
BOX CONTENTS:
Before beginning assembly, please take a moment to
familiarize yourself with the box contents. It will include:
(QTY) Description:
(2) 48” Black frame side sections
(1) 23” Black frame ‘Top’ section
(1) 23” Black frame ‘Bottom’ section
(2) 46” Panel Stops
(1) 23” Beveled Wall Mount Stretchers
(1) 23” Beveled Cross Support
(1) 23” Cross Support
(1) Fabric wrapped fi berglass panel
(1) Loaded vinyl barrier
HARDWARE BAG CONTENTS
(QTY) Description:
(8) Cams-locks
(8) Cam-pins
(8) Wooden Dowels
(8) Medium Phillips Screws
(8) Short Phillips Pan Head Screws
(2) Long Phillips Pan Head Screws
(2) Heavy Duty Phillips Screws
(2) Plastic Drywall Anchors
Warranty: Please inspect panels immediately after purchase and before mounting. Primacoustic Broadway acoustic panels are guaranteed to be free of manufacturing defects for a period of thirty (30) days after purchase. In the
unlikely event that a defect is uncovered, please call 604-942-1001 to obtain an RA number (Return Authorization number) from Primacoustic before the thirty (30) day warranty period expires. Once you have obtained an RA number
you must return the product, freight prepaid, within fi fteen (15) days after the date the RA number is issued. Please return the product in the original packaging (or another, affording an equal degree of protection) with all of the following:
(1) RA number clearly marked on the returned package; (2) a receipt or bill of sale showing proof of purchase from an authorized retail seller; and (3) a written note describing the defect and including your name, address, telephone
number and the applicable RA number. You are solely responsible for all shipping and insurance costs for returning the product to Primacoustic, and you will not be reimbursed or compensate for any loss or damage incurred during
return shipping. Primacoustic will at its discretion repair or replace the panel. Should the panel be no longer available, Primacoustic reserves the right to exchange this with a panel of similar performance and value. Due to different dye
lots, Primacoustic cannot guarantee exact color match. This Warranty shall solely extend to the original owner and is limited to manufacturing defects and excludes any damage due to wear and tear, abuse, misuse, misapplication,
color fading or deterioration due to prolonged exposure to ultra violet light, smoke, humidity or other environmental factors. It is understood that the use and suitability of Broadway is entirely the responsibility of the buyer or specifying
engineer and as such, these parties agree to hold Primacoustic, or it’s associated company, and/or offi cers, harmless from any responsibility whatsoever other than what is clearly outlined in this warranty.
1638 Kebet Way, Port Coquitlam, BC Canada V3C 5W9
Primacoustic is a division of Radial Engineering Ltd.
Tel: (604) 942-1001 • Fax (604) 942-1010
FRAME ASSEMBL Y INSTRUCTIONS
Place the two 48” side sections on the fl oor with the
pre-drilled holes facing up. For each side section
1
push eight wooden dowels into the pre-drilled holes.
For each side section thread four cam-pins into the
holes at the ends as shown.
Place the two the 23” top and bottom sections on the
fl oor with the pre-drilled holes facing up. Push four
cams-locks into the pre-drilled cavities on the 23” top
and bottom sections. Ensure the open side of the
cam-lock, marked with an arrow head, is facing the
toward the edge so it can mate with the cam-pin.
Connect the 23” top and bottom sections to a 48”
2
side section. Note the 23” top section has small
piolet holes drilled along the front edge. Use a
Phillips screwdriver to tighten the cams snuggly.
If the cam-locks won’t tighten ensure the arrow
head is facing outward so the cam-pins line up with
the cam-locks.
Piolet Holes
TOP
Locking Cams
BOTTOM
Set the cross support with the beveled edge onto the
wooden dowels near the top section. Be sure that the
3
beveled edge is facing inward and toward the bottom
section (see diagram). The beveled cross support is
used to wall mount the completed FullTrap.
Set the cross support with the square edge onto the
wooden dowels near the bottom section.
Beveled Edge
TOP
BOTTOM
Set the other 48” side section onto the frame
assembly being care full to line up the cam-pins
4
and dowles. Tighten all cams snuggly using a
Phillips screwdriver.
Lay the completed frame down so the front is
facing up.
FRONT
www.primacoustic.com
VINYL BARRIER ASSEMBLY
www.primacoustic.com
Set two panel stops with the four small piolet
5
holes facing up, and larger pre-drilled holes facing
sideways. Lay the vinyl material on top of the panel
stops. Line up the edges fl ush and keep the vinyl
material square with the panels stops (diagram).
Using eight short Phillips pan head screws fasten
the vinyl material to the panel stops. Screw through
the vinyl into the small piolet holes (diagram). Avoid
stretching the vinyl between scews. It should lay
fl at and limp between screws.
With the frame assembly lying down on it’s back.
Set the vinyl barrier assembly into the frame with
6
the panel stops facing upward (diagram).t
Using eight medium Phillips screws, attach panel
stops into the pre-drilled hole locations on the
inside of the 48” side sections (diagram).
Lower in the Broadway fi berglass panel with the
fabric covering facing outward. The panel should fi t
7
sungly. Do not force the panel into place.
Fasten the Broadway fi berglass panel at the top
end with two Philips pan head screws through the
8
pre-drilled holes in the 23” top section. This will
prevent the panel from becoming accidentally
dislodged.
WALL MOUNTING INSTRUCTIONS
12"
Select the location where you would like to hang your
FullTrap. Ideally, the center of the FullTrap should be
positions at the same height as your ears when seated in
your listening position but this is fl exable if room decore or
listening position dictates otherwise.
Mark the wall where the top of the FullTrap will be. Measure
down from that line 12 inches and mark the top of the wall
support position. Use a bubble level and pencil to make a
straight horizontal line that will guide you in mounting the
wall support level.
The FullTrap should be screwed into the wall studs. Locate
and mark two wall studs that are 12” to 16” apart. A stud
fi nder is reccomended for this.
Alternatively, use wall anchors capable of supporting
at least 55lbs. For sheetrock walls 1/4” toggle bolts are
recomended. For masonry and cement block use an
approriate anchor made for that material.
Set the wall support level along the line you just made. Be
sure the beveled edge is facing up and outward from the
wall (see diagram). Using a screwdriver or cordless drill to
fasten the wall support to the studs, or appropriate anchor.
With the help of a second person, lift the completed
FullTrap assembly up and gently rest the beveled cross
support on the back of the Fulltrap down onto the beveled
wall stretcher. The opposite beveled edges will lock
together and safely support the FullTrap on the wall.
Mount wall support directly
to studs or use appropriate
anchors or toggle bolts.
Top of wall support
is 12” below the top
of the FullTrap.
Note the orientation of
the beveled edge on
the wall support.
CORNER MOUNTING INSTRUCTIONS
The FullTrap may be mounted in 90 degree corners by
using 45° Joist Hangers (not included with the FullTrap)
available from your home center store or building supplier.
Measure and cut two pieces of 2” x 6” lumber in 17 inch
lengths. Screw the hangers onto the ends of the 2 x 6
lumber with one inch wood screws. Mount the hanger and
lumber assemblies in the corner using your bubble level
and drywall anchors. Position the corner mounts so they
will be hiden behind the FullTrap when installed. Use eight
drywall anchors for each hanger and lumber assembly.
Mount the beveled wall stretcher to the top 2 x 6 and hang
the FullTrap the same way as for wall mounting.
45° Joist Hanger
Beveled wall stretcher
mounted to 2 x 6.
45 Degree Joist Hanger.
Corner mount assembly
consisting of two 45° Joist
Hangers and 2 x 6 Lumber.
FullTrap
45° Joist Hanger
2 x 6 Lumber
Beveled Wall
Stretcher
www.primacoustic.com
1638 Kebet Way, Port Coquitlam, BC Canada V3C 5W9
Tel: (604) 942-1001 • Fax (604) 942-1010
Primacoustic is a division of Radial Engineering Ltd.
Loading...