Page 1
Calf Table
Operation Manual and Reversal Instructions
Operator’s Manual with Reversal Instructions
Safety related warnings and instructions follow this Alert Symbol and are used to get your attention so you may avoid serious
injury or death to you and others. Read the Operator’s Manual in its entirety!
OP_Man-CTwRev_v2-1011
Page 2
Welcome
Handle bigger calves with less effort with Priefert’s unique
patented two-stage pivot calf table. Designed so a smaller
individual can roll a bigger calf with less effort, this Calf Table
helps take the work out of a typically tough job. This is the
easiest tilting table on the market and is the safest most
productive way to work calves weighing up to 450 lbs. Vertical
bars are removable for total access to any part of calf’s body
and includes a leg hobble feature to aid with castration. If you’re
not “ropin’ and dragging” the Priefert Calf Table is a sure bet to
help processing those calves.
Priefert Manufacturing maintains an ongoing program of continuous
product improvement. Therefore, Priefert reserves the right to make
improvements in design or specification changes without incurring any
obligation to replace said items on units previously sold.
There is a possibility that some illustrations in our manuals were of
prototype models, design of production models may vary in detail from
those shown in our manuals.
REMEMBER SAFETY FIRST!
Be Alert - Eliminate unsafe habits and risky behavior, recognize
hazards as they exist and read and follow the Operator’s Manual
for your Priefert Calf Table.
Getting Started
This manual provides information necessary to effectively operate your
Calf Table. This manual also provides manufacturer's recommendation
of proper use and operation, as well as, instructions for reversal of the
head gate for right side entry, or left side entry.
The information presented in this operator’s manual is applicable only to
the make and model of the Calf Table at time of purchase. Contact your
authorized dealer or manufacturer for any needed additional information.
Terminology
“Right” or “Left” as used in this manual is determined by facing forward
in the direction of calf loading while in use unless otherwise stated.
“NOTE:”
assist in operating the implement.
“IMPORTANT:”
the operation or maintenance of the implement.
provides the operator a brief summary of information that will
denotes that the following content has significance in
Owner Assistance
Please contact your Priefert Ranch Equipment Dealer if you have any
questions regarding your Priefert Calf Table, need repairs, or need to
order replacement parts.
The parts on your Calf Table have been specifically designed and
should only be replaced with approved Priefert Manufacturing parts.
Customer Service
Contact your Priefert Ranch Equipment dealer to discuss any issues
that you may be experiencing. Allow them the opportunity to assist in
correcting any problems, or answer questions that you may have.
For further assistance, contact:
Priefert Manufacturing
Attention: Customer Service
2630 South Jefferson
P.O. Box 1540
Mount Pleasant, Texas 75456-1540
1-800-527-8616
www.priefert.com
sales.priefert.com
2
Page 3
Table of Contents
Welcome 2
Getting Started ................................................................................ 2
Terminology .................................................................................... 2
Owner Assistance ........................................................................... 2
Customer Service ........................................................................... 2
Safety 4
Livestock Safety .............................................................................. 4
Livestock Behaviors ........................................................................ 4
Precautionary Measures ................................................................. 4
Section 1: Operation 5
Floor Width Adjustments ................................................................. 5
Tilt Locked or Unlocked................................................................... 5
Two-Stage Pivot Tilting ................................................................... 5
Side Bar Removal ........................................................................... 5
Section 2: Headgate Reversal 6
Removing Headgate ........................................................................ 6
Reversal Assembly .......................................................................... 6
Section 3: Component Description 7
Components .................................................................................... 7
Part Numbers & Description ............................................................ 7
Warranty 8
References 9
3
Page 4
Safety
Caution
Be familiar with handling livestock prior to use of this
equipment. Working with livestock carries inherent risk of
injury or death.
Livestock Safety1
One of the most important issues for consideration when handling
livestock is safety. Although considered domesticated animals, working
with livestock carries with it an inherent risk of danger. It is important to
understand that livestock have both instincts and habits, known as
behavior patterns, that are based on actions that make them the most
comfortable. These instincts and habits allow them to react to changes
in their environment. Many instincts and habits are strong and potentially
dangerous. Using common sense, practicing caution, and understanding
livestock behavior can greatly reduce a handlers risk and enable him or
her to work safely with livestock. This article will detail some important
livestock behaviors as well as cautionary tips to practice when handling
livestock.
Livestock Behaviors
Animals who are used to being around other livestock can become
frightened and agitated when separated, becoming dangerous and
difficult to handle.
The maternal instinct is also very powerful. Many times these
instincts are not evident in an animal’s behavior until shortly after
giving birth. It is important to recognize these behavior patterns and
use appropriate caution.
Another behavior pattern that livestock may exhibit is a territorial
instinct. Feed time is when this instinct is most readily observable.
A valuable behavior is the instinct to follow the leader. Often times,
all that is required is to begin one animal moving and the rest will
follow.
Livestock exhibit the most activity at sunrise and sunset. In
contrast, livestock are the most inactive during night and at midday.
The flight zone is one of the most important principles regarding
livestock behavior and safe handling. It is an animal’s personal
space. Livestock will react in a variety of ways according to a
handlers activities relative to their flight zone. For example,
livestock will face a handler and maintain a safe distance, when the
handler is outside their flight zone. In contrast, livestock will turn
away from a handler who enters their flight zone. Individual animals
will have flight zones of varying size. Working from the edge of the
flight zone will generally keep livestock calm and manageable.
The point of balance is another important behavioral principle to
understand. An animal’s point of balance is located at their
shoulders. An animal will move depending on a handlers position
relative to their point of balance. This principle can be used to
calmly and easily be encourage livestock through crowding pens,
chutes, and squeezes. For example, when a handler stands behind
the animal’s point of balance, the animal will move forward. When
the handler stands in front of an animals point of balance, the
animal will stop or back up. To encourage an animal forward,
simply walk towards the animal, crossing the point of balance, and
it will move forward.
Precautionary Measures
The following are precautionary measures that are recommended to
anyone when working with livestock.
Be alert. It is impossible to fully know or predict an animals
actions. Always be aware of what is happening around you. This is
particularly important when handling livestock at sunrise and
sunset when livestock are most active.
Keep animals together. Livestock will be more calm and
cooperative when in groups. When alone, they quickly become
agitated and frightened making them dangerous and difficult to
handle.
Carefully approach animals. Because of the placement of their
eyes, cattle have approximately a 270 degree range of vision.
Despite their range of vision, cattle have poor depth perception,
and are unable to see behind them. To reduce risk, always
announce yourself when approaching an animal.
Leave yourself an out. Never enter small enclosed areas with
livestock. If unavoidable, always be sure there is always a fast and
easy method of escape.
Avoid quick movements and loud noises. Livestock can startle
and frighten easily. Move slowly and deliberately around livestock.
Be careful not to create excess noise.
Be patient. When working with livestock in a crowding pen, chute,
or squeeze, prodding an animal when it has no place to go is
dangerous. Animals can react quickly and violently.
Respect livestock. Do not fear them. Underestimating an
animal’s size, strength, and speed can result in serious injury.
Always consider mature males to be dangerous. Be aware of
animals who are sick, injured, or otherwise frightened.
Remember that livestock draw upon past experiences and
treatment when reacting to a situation.
Caution
Train new workers and handlers before allowing them to work
with livestock. The majority of the time, accidents with livestock
are the result of human error rather than an animal problem. A lapse in
judgment, inexperience, or unpreparedness are major causes of
accidents with livestock. Many times, handlers attempt jobs that require
more assistance than is available. Whatever the reason, many accidents
can be avoided if handlers use common sense, follow safety guidelines,
and make every effort to understand livestock behavior.
4
Page 5
Section 1: Operation
Operation of the Priefert Calf Table (CT)
Refer to Figures 1-1 thru 1-10
1. Adjust floor width settings to the appropriate setting for the size
calves you intend to work. The table has three different
adjustment holes for width options to fit various calf sizes.
(See Fig. 1-1)
Figure 1-1 Adjustment Holes
To change width simply put the table in
tilted position; remove the lynch pins that
secure the side panel in place; lift and
place side panel in desired hole location.
(See Fig. 1-2)
Note: All calf tables are shipped to allow branding on the left side of the
animal. Priefert calf tables are reversible. (See Section 2: Reversal
Instructions, pg. 6)
2. Using chain or other acceptable
means, secure calf table to alley or
Squeeze Chute. Calf Table should
hold position under rigorous use.
3. Determine “locked” (for calves to
remain standing) or “unlocked”
pos i t i o n f o r til t i n g op t i o n.
(See Fig. 1-3)
4. By pushing “away” on red side
squeeze friction lock handle,
operator should open table sidesqueeze to its fullest width..
(See Fig. 1-4)
5. By pressing “down” on red handle
of friction lock with left hand and
pushing “away” on red handle of
headgate, open headgate wide
enough to encourage calf to enter
table (see Fig. 1-5).
6. Catch calf by the neck as its head
passes headgate by pulling red
han dle on headgate toward
operator. (See Fig. 1-6)
7. Operator should quickly pull side
squeeze against calf until calf is
adequately restrained.
Figure 1-2 Lynch Pins
Figure 1-3 Tilting Option
Figure 1-4 Open Side-Squeeze
Figure 1-5 Encourage calf
8. Operator should pull on side squeeze handle to pull calf table over
in its two-stage cycle. (See Fig. 1-7)
Because of Priefert’s patented
two-stage pivot system, with
practice, operator will soon
catch the head, squeeze, and
tilt with continuous motion.
9. In the fully tilted position, calves are easily accessible for branding,
10. Operator may remove side bars by
Note: Complete removal may be achieved
by rotating bar so bottom swedge is
aligned with slot.
11. Full access is now available for
12. Upon completion of work, operator
13. To release calf, operator should
Figure 1-7 Squeeze & Tilt
castration, injections, or other procedures where restraint is
required.
pulling down against spring tension
while pressing bar “toward” calf.
Figure 1-8 Side Bar Removal
operator to give all shots and work
calf with ease.(See Fig. 1-9)
can return calf for exiting by lifting
and allowing two-stage pivot to
assist return to standing position.
push on red squeeze handle to
release side squeeze to fully open
position. Next, push down on
friction lock’s red handle and push
head gate open to full release calf.
Calf table is now positioned to next
calf to be caught.(See Fig. 1-10)
Figure 1-10 Calf Release
Figure 1-6 Catch Calf
Figure 1-9 Full Access
5
Page 6
Section 2: Reversal Instructions
Headgate Reversal
Refer to Figure 2-1 thru 2-10
All calf tables are shipped to allow branding on the left side of the
animal. Priefert calf tables are reversible. It's reversibility allows the
freedom to utilize this in any handling configuration and provides the
operator access for either side of the calf.
Removing Headgate
1. Remove the Cotter Pin from the
Slip Rod and slide the rod out of
the hole.(See Fig. 2-1)
Figure 2-1 Remove Cotter Pin
4. Remove the ⅝” x 3½” bolt and washer attaching the Headgate to
the Calf Table Floor.. (See Fig. 2-4) Remove the Headgate from
the assembly, and move it to the other side of the Calf Table.
Note: The orientation of the Headgate remains the same in both
Standard and Reversed configurations. Do not turn or rotate, simply
move to opposite end of Table and assemble in inverse order of
disassembly. (See Fig. 2-5)
Figure 2-4 Remove Headgate
1. Slide the other end of the
Slip Rod out of the Latch
handle to remove it from
the assembly.(See Fig. 2-2)
2. Remove the Spring from
the Latch handle , then
remove the Latch handle
from the Trigger box.
3. Remove the (2) ½” x 1”
bo l t s at t a c hi ng t h e
Headgate Guide to the
Headgate. Remove the
Headgate Guide from the
assembly. (See Fig. 2-3)
Figure 2-2 Remove Slip Rod
Figure 2-5 Headgate Orientation
Reversal Assembly
1. After relocating the Headgate to opposite end of Table, insert
the ⅝” x 3½” bolt and washer into the bottom hole of the Headgate
from where it was removed, and secure it to the Calf Table Floor.
2. Align the holes i n the
Headgate Guide with the
holes in the Headgate and
secure it with the ½” x 1” bolts.
Impo rt an t: Headgate Guide
attaches to the INSIDE during
reversal due to structural design of
Headgate. (See Fig. 2-6)
Figure 2-6 Headgate Guide Inside
Figure 2-3 Remove Headgate Guide
6
3. Insert the Latch Handle into the Trigger Box and attach the spring.
4. Slide the Slip Rod into the hole in the Latch Handle. Insert the Slip
Rod into the hole at the bottom of the Headgate, and Secure it with
the Cotter Key.
Page 7
Section 3: Component Description
3
10
3
1
6
7
8
Table w/Headgate Reversed
4
1
12
16
11
15
9
14
2
Part Number Item name Qty
NS
BT08414001.5 TUBE .840 14GA 1 1/2 1 ea
1 CTAR CALF TABLE ACCESS ROD 9 ea
2 CTF041.532 FLAT 1/4 X 1 1/2 X 32" false 1 Pc" 1 ea
3 CTHG-P CALF TABLE HEAD GATE 1 ea
NS
CTLC-P CALF TABLE LEG CHAIN 1 ea
4 CTLEG-P CALF TABLE LEG 1 ea
5 CTSLRODREC-P CALF TABLE SLIP ROD REC 1 ea
6 CTSQSIDE-P CALF TABLE SQEEZE SIDE 1 ea
7 CTSTAND-P CALF TABLE STAND 1 ea
8 CTWKSIDE-P CALF TABLE WORK SIDE 1 ea
9 G200 GRIPPER 7/8 X 4.375 BG RED 3 ea
10 HC HEAD CHAIN 1 ea
NS
POS STICKER-L POINT OF SALE STICKER LARGE 1 ea
11 SRCT SLIP ROD FOR CALF TABLE HEADGATE 1 ea
12 SS SMALL SPRING 2 ea
13 SSRCT SIDE SQUEEZE SLIP ROD FOR CALF 1 ea
14 FLM FRICTION LATCH MASHED IN WELD 2 ea
15 FM031 COTTER KEY 3/16 X 1 ZP 2 ea
NS
FM04LP LYNCH PIN 1/4 ZP 1 1/4 EFFECT 2 ea
13
7
5
Part Number Item name Qty
NS
D103 DECAL STARBURST FACTORY REP 1 ea
NS
D125 DECAL NOTICE ALTERATION/MODIFI 1 ea
NS
D135 DECAL MADE USA/GOD TRUST W/FLG 1 ea
NS
D200 DECAL CAUTION DO NOT TRANSPORT 1 ea
NS
D210 DECAL DANGER DO NOT OIL FRICTI 2 ea
NS
D525 DECAL DIAMOND CALF TABLE 3 ea
NS
D560 D560L RED REFLECTIVE PATCH 2 ea
NS
DMED DECAL MEDIUM PRIEFERT 2000 3 ea
NS
FB041.25ZPG2HEX BOLT 1/4 X 1 1/4 G2 ZP 1 ea
NS
FB081.00ZPG2 BOLT 1/2 X 1 G2 ZP 2 ea
NS
FB083.00ZPG2 BOLT 1/2 X 3 G2 ZP REP 4 ea
NS
FB103.50BKG5 BOLT 5/8 X 3 1/2 G5 BK REP 1 ea
NS
FB104.50BKG2 BOLT 5/8 X 4 1/2 G2 BK 1 ea
16 FM05EB EYE BOLT 5/16 PLATED 1 ea
NS
FN04ASLN FASTENER NUT 1/4 ALL ST ZP REP 1 ea
NS
FN05ASLN FASTENER NUT 5/16 ALL STLK 1 ea
NS
FN08ASLN NUT 1/2 ZP ALL ST LOCK HEX 6 ea
NS
FN10NYLN NUT 5/8 NYLOCK ZP 2 ea
NS
ZF042.25 FLAT 1/4 X 2 1/4 DIAMETER 1 ea
NS - ITEM NOT SHOWN OR NOT IDENTIFIED IN THIS ILLUSTRATION
7
Page 8
Limited Warranties:
Priefert Manufacturing Company, Inc., (“Priefert”) 2630 South Jefferson, P.O. Box 1540, Mount Pleasant, TX 75456-1540,
warrants for one (1) year from the purchase date to the original non-commercial, governmental, or municipal purchaser
(“Purchaser”) and warrants for six (6) months to the original commercial or industrial purchaser (“Purchaser”) that the product
purchased are free from defects in material or workmanship. Priefert will replace or repair, free of charge to the original purchaser
any part(s) found, upon examination at our factory, to be defective under normal use and service due to defects in material or
workmanship, provided that the original purchaser:
a. Notifies Priefert in writing of any defect in material or workmanship within the above specified warranty period.
b. Returns must be routed through an authorized Priefert dealer or distributor from whom the purchase was made.
c. Purchaser is responsible for cost of shipping.
In no event will Priefert be held liable under this warranty unless written notice is received and failure must have occurred within
the warranty period. Genuine Priefert replacement parts and components will be warranted for 90 days from date of purchase, or the
remainder of the original equipment warranty period, whichever is longer.
This limited warranty does not apply to any part of the product which has been subjected to improper or misintended use,
negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong oil or lubricants, or repairs
that have been made with parts other than those obtainable through Priefert, or which has served its usual life. This limited warranty
does not apply to any expendable item such as blades, shields, guards, or pneumatic tires, or other trade accessories since these
items are warranted separately by their respective manufacturers, except as specifically noted in your Operator’s Manual.
Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf
of Priefert. Only Priefert is authorized to make any representation to the purchaser concerning “normal” use and service for its
product as described in the Operator’s Manual, or in authorized printed materials or stickers affixed to the product.
If after examination of the product and/or part(s) in question; Priefert finds them to be defective under normal use and service due
to defects in material or workmanship,
Priefert will:
1. Repair or replace the defective product or part(s); if Priefert has made several reasonable number of attempts in repairing the
product and/or part(s) to conform to the warranty; then
2. Priefert will replace part(s) or product.
3. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Priefert and for returning
product and/or part(s) to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation
cost for the product or part(s) from the Dealer to the factory.
The choice of remedy shall belong to Priefert. Repair or replacement are the only remedies against Priefert under this limite d
warranty.
Limitation of Liability:
1. Priefert disclaims any express (except as set forth herein) and implied warranties with respect to the product including, but not
limited to, merchantability and fitness for a particular purpose.
2. Priefert makes no warranty as to the design, capability, capacity, or suitability for use of the product.
3. This warranty shall not be interpreted to render us liable for injury or damages of any kind or nature to person or property.
Priefert will not be liable for any special, incidental or consequential damages based upon breach of warranty, breach of
contract, negligence, strict tort liability, or any other legal theory. Such damages include but are not limited to loss of crops,
loss of savings or revenue, cost of capital, loss of use of equipment, facilities or services, down time, expense or loss incurred
for labor, supplies, substitute machinery, rental, and claims of third parties including customers, and injury to property.
Supplementary:
1. Proper venue for any lawsuits arising from or related to this limited warranty shall be only in Titus County, Texas.
2. Priefert may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be
a waiver of any other term.
3. If any provision of this limited warranty violates any applicable law and is held unenforceable, then the invalidity of such
provision shall not invalidate any other provisions.
4. Applicable law may provide rights and benefits to purchaser in addition to those herein.
8
Page 9
References
1.
Jill Webster Ph.D., & Mark Gonzalez; Livestock Safety; Agricultural Systems Technology and Education, Utah State University Extension; Utah
State University , <http://extension.usu.edu/files/publications/factsheet/AHS-11.pdf>
2.
Occupational Safety and Health Administration (OSHA), Safety for Agricultural Equipment, 29 CFR 1928.57, http://www.osha.gov/pls/oshaweb/
owadisp.show_document?p_table=STANDARDS&p_id=10958.
Suggested References
Priefert assumes no liability for the use or misuse of information provided in the following references:
TEAGASC, Agriculture and Food Development Authority,
http://www.teagasc.ie/newsletters/safety/farmsafetyguide.asp
Beef Cattle Handling: A Practical Safety Guide,
http://www.farmsafety.ca/pages/pages/manuals-dwnld.html
NASD, National AG Safety Database,
Federal Laws and Regulations Affecting Farm Safety,
http://nasdonline.org/document/1842/d001777/federal-laws-and-regulations-affecting-farm-safety.html
FEMA, Farm Equipment Manufacturers Association, Safety 4 Just Kids, 2008,
http://www/farmequip.org/safety
Includes AG Safety Links for additional information and materials.
Farm Safety Association, Guelph, Ontario, The Safe Movement of Agricultural Equipment on the Roadway,
http://www.farmsafety.ca/pages/manuals -dwnld.html
9
Page 10
Loading...