Pridom PFCM123HX, PFCM183HX, PCM123HX, PCM183HX Owner's Manual
HEAT PUMP
REMOTE CONTROLLER ILLUSTRATION
Thank you very much for purchasing our heat pump.
Please read this owner's manual carefully before using
your heat pump.
202055091446
The design and specifications are subject to change without prior notice
for product improvement. Consult with the sales agency or manufacturer
for details.
PFCM123HX
PFCM183HX
PCM123HX
PCM183HX
11
2
3
4
7
8
9
9
10
10
11
12
Handling the remote controller ......................................................
Remote controller Specifications...................................................
Function buttons .................. .........................................................
Indicators on LCD ..........................................................................
How to use the buttons
Initial setting the clock ...................................................................
Auto operation.................................................................................
Cooling/Heating/Fan operation......................................................
Dehumidifying operation ...............................................................
Adjusting air flow direction............................................................
Timer operation...............................................................................
Example of Timer setting ..............................................................
CONTENTS
Use the remote controller within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
Location of the remote controller.
8m
CAUTIONS
The heat pump will not operate if curtains, doors or other materials
block the signals from the remote controller to the indoor unit.
Prevent any liquid from falling into the remote controller. Do not expose
the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the heat pump may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller, either move
these appliances or consult your local dealer.
The remote controller is powed by two dry batteries(R03/LR03X2) housed in the
rear part and protected by a cover.
(1) Remove the cover by pressing and sliding off.
(2) Remove the old batteries and insert the new batteries,placing the(+) and (-)
ends correctly.
(3) Reattach the cover by sliding it back into position.
NOTE: When the batteries are removed, the remote controller erases all
programming. After inserting new batteries, the remote controller must be
reprogrammed.
Replacing batteries
Handling the remote controller
22
Keep the remote controller where its signals can
reach the receiver of the unit.
CAUTIONS
Do not mix old and new batteries or batteries of different types.
Do not leave the batteries in the remote controller if they are not
going to be used for 2 or 3 months.
Do not dispose batteries as unsorted municipal waste. Collection
of such waste separately for special treatment is necessary.
MODE
FAN S
PEED
SWING V
SWING H
SLEEP
IONIZER
TIMER ON
TIMER OFF
CLOCK
SELF CLEAN
RESET LOCK
AUTO
COOL
DRY
HEAT
FAN
TEMP.
SET
CLOCK
TIMER
HOUR
ON
OFF
M
Model
Lowest Voltage of
CPU Emitting Signal
Rated Voltage
8m
3.0V(Dry batteries R03/LR03 2)
2.4V
Remote Controller Specifications
1. Operating Mode: AUTO, COOL, DRY, HEAT(cooling & heating models only),
and FAN.
2. Timer Setting Function in 24 hours.
OOO O
3. Indoor Setting Temperature Range : 6 2 F~86 F(17 C~30 C).
4. Full function of LCD (Liquid Crystal Display).
Environment
Signal Receiving
Range
Performance Feature
Function buttons
1
2
Each time the button is pressed, the operation
mode is selected in a sequence of following:
3
MODE Button
33 44
3
4
ON/OFF Button
Operation starts when this button is pressed
and stops when this button is pressed again.
NOTE: Please do not select HEAT mode if the
machine you purchased is cooling only type. Heat
mode is not supported by the cooling only
appliance.
AUTO
COOL
DRY
HEAT FAN
SLEEP Button
NOTE: While the unit is running under SLEEP
mode, it would be cancelled if MODE, FAN
SPEED or ON/OFF button is pressed.
Active/Disable sleep function. It can maintain
the most comfortable temperature and save
energy. This function is available on COOL,
HEAT or AUTO mode only .
SWING V Button
Used to stop or start horizontal louver movement and set the desired up/down air flow
direction. Push once, the louver changes 6
degree in angle. Keep pushing more than 2
seconds, the louver will swing up and down
automatically.
MODE
FAN SPEED
M
AUTO
COOL
DRY
HEAT
FAN
Sliding door
(closed)
MODE
FAN SPEED
SWING V SLEEP
TIMER ON
TIMER OFF
CLOCK
RESET LOCK
M
AUTO
COOL
DRY
HEAT
FAN
4
5
7
8
9
10
11
12
13
14
15
2
1
TURBO
LED
Sliding door
(opened)
RG05F2/BGEU1
OOOO
23 F~140 F(-5 C~60 C)
SWING H
16
5
SWING H Button
Used to stop or start vertical louver movement
and set the desired left/right air flow direction.
The vertical louver changes 6 degree in angle
for each press.If keep pushing more than 2
seconds,the vertical louver swing feature is
activated.(Not applicable to all the units,please
refer to the OWNER S MANUAL for details).
SELF CLEAN
6
I FEEL
I FEEL /SELF CLEAN Function
Press this button less than 2 seconds will
initiate I FEEL function. And if keep pressing
this button more than 2 seconds, the
SELF CLEAN function is initiated.
6
Loading...