OWNER’ S MANUAL
WIRE CONTROLLER OF AIR CONDITIONER
MODEL: KJR-12B/DP(T)-F
Thank you very much for purchasing our product.
Before using your unit, please read this manual carefully and keep it for future reference.
● This manual gives detailed description of the precautions
that should be brought to your attention during operation.
● In order to ensure correct service of the wired controller
please read this manual carefully before using the unit.
● For convenience of future reference, keep this manual
after reading it.
CONTENTS
1. SAFETY PRECAUTION.............................................................................. 1
2. SUMMARIZE............................................................................................... 2
3. FUNCTION SUMMARY............................................................................... 2
4. NAME AND FUNCTION OF INDICATORS ON THE WIRE
CONTROLLER............................................................................................ 3
5. INSTALLATION METHOD........................................................................... 4
6. NAME AND OPERATION OF THE BUTTON ON THE WIRE CONTROL-
LER.............................................................................................................. 5
7. USING METHOD ........................................................................................ 7
AUTOMATIC OPERATION......................................................................... 7
COOLING/HEATING/FAN ONLY OPERATION.......................................... 7
DRY OPERATION....................................................................................... 8
TIMER SETTING........................................................................................ 8
TIMER ON AND TIMER OFF BOTH........................................................... 8
CHANGE TIMER......................................................................................... 9
8.TECHNICAL INDICATION AND REQUIREMENT ...................................... 9
1. SAFETY PRECAUTIONS
The following contents are stated on the product and the operation manual,
including usage, precautions against personal harm and property loss, and the
methods of using the product correctly and safely. After fully understanding the
following contents (identifiers and icons), read the text body and observe the
following rules.
Identifier description
Identifier Meaning
Warning
Means improper handling may lead to personal injury or
Caution
[Note]: 1. “Harm” means injury, burn and electric shock which need
long-term treatment but need no hospitalization
2. “Property loss” means loss of properties and materials.
Icon description
Meaning lcon
It indicates forbidding. The forbidden subject-matter is indicated in the
icon or by images or characters aside.
It indicates compulsory implementation. The compulsory subject-matter
is indicated in the icon or by images or characters aside.
Means improper handling may lead to personal death or
severe injury.
property loss.
1
Warning
Delegate
W
arning
Usage
W
arning
installation
Forbid
Forbid
Please entrust the distributor or professionals to install
the unit. The installers must have the relevant know-how.
Improper installation performed by the user without perm
ission may cause fire, electric,shock, personal injury or
water leakage.
Do not spray flammable aerosol to the wire
controller directly. Otherwise, fire may occur.
Do not operate with wet hands or let water enter the wire
controller. Otherwise, electric shock may occur.
2. SUMMARIZE
Usage condition:
1. Power supply: 5V DC.
2. Operation temperature:
-15°C(-5°F)~ +43°C(+109°F).
3. Operation humidity: 40%-90%, RH.
3. FUNCTION SUMMARY
Main function:
1. Connecting to indoor unit by A, B, C,
D, E termina.;
2. Button setting action mode.
3. LCD display.
4. Timer for rest time.
2
4. NAME AND FUCTION OF INDICATORS ON THE
CONTROLLER
1
2
2
Timer ON/OFF
1
Operation mode indication
① Operation mode indication:
When press " MODE " button, the follow-
ing mode can be selected in circle. Auto
→Cool →Dry→Heat→Fan only→Auto.
For cooling only model,heat mode is
skipped.
② Timer :
When adjust setting on time or only on
time is set, the "ON" is lighted.
3
Follow me function
4
ON/OFF indication
5
Fan speed indication
1 12 1 12
Lock
6
Temperature display zone
7
When adjust setting off time or only off
time is set , the "OFF" is lighted. If on
and off timer are both set, the"ON" and
"OFF"are both lighted.
③ Follow me function:
There is a temperature sensor inside the
wire controller, after setting temperature,
it will compare the two temperatures,
and the space of wire controller will be
3
the same as setting temperature. It is
available under cooling, heating, auto
mode.
④ ON/OFF indication :
When it is on, the icon display,
otherwise it is extinguished.
⑤ Fan speed indication :
There are four fan modes : low, middle,
high, auto. For some models, no middle
fan then the middle fan is seen as high
5. INSTALLATION METHOD
5-way terminal
Wire Controller
5-Core Shield Cable
speed.
⑥ Lock:
When the " LOCK " button is pressed,
the icon appear and other buttons is
unable, press again, the icon disappear.
⑦ Temperature display zone:
Generally it displays setting tempera-
ture, it can be adjusted by press
temperature button ▲ and ▼. But in fan
mode, no display here.
Emitter tube
+5V
RUN
Indoor switch board
GND
Indoor Unit
4
When a wire controller is needed, a small 5-way terminal should be added,fix an
infrared emitter with gumwater near the receiver on the switch board. Connect its
anode and cathode to A and B,and +5V, GND, RUN to C, D, E on the switch board.
6. NAME AND OPERATION OF THE BUTTON ON THE
WIRE CONTROLLER
ON / OFF BUTTON
⑦
MODE BUTTON
TIMERON BUTTON
TIMER OFF BUTTON
FOLLOWME BUTTON
ELECTRICAL
HEATER BUTTON
RESET BUTTON
①
②
③
④
⑤
⑥
ADJUST BUTTON ▲
TIMER
FOLLOW
ME
ON
TIMER
AUXIL
HEATER
MODE
LOCK
RESET
OFF
FANSPEED
ECO
TEMP
SWING
⑧
ADJUST BUTTON ▼
⑨
⑩
ECONOMY BUTTON
11
FAN SPEED BUTTON
12
13
SWING BUTTON
LOCK BUTTON
5
① Mode botton:
When press this botton,the operation
mode change as the following
sequence:
→AUTO → COOL→DRY→HEAT→FAN
Remark: For the cooling only model, the
heating mode is skipped.
② Timer on button :
Press this button, timer on function is
active. Then every press, the time
increase 0.5h, after 10h, 1h
increasement after each press. If cancel
this Function,just set it to "0.0" .
③ Timer off button:
Press this button, timer off function is
active.Then every press, the time
increase 0.5h, after 10h, 1h
increasement after each press. If
cancel this function, just set it to "0.0" .
④ Follow me button:
When under cool, heat and auto mode,
press this button, follow me function is
active. Press again, this function is
ineffective.
Electrical heater button :
⑤
If press this button in heat mode, electri-
cal heater function become ineffective.
⑥ Reset button(hidden):
Use a 1mm stick to press in the little hole ,
then the current setting is canceled . The
wire controller enter into original state.
⑦ON/OFF button:
When in off state, press this button, the
indicator is on, the wire controller enter
into on state, and send setting information
to in door Pcb. When in on state,press this
button, the indicator is off, and send
instruction. If timer on or timer off has
been set, it concel this setting then send
instruction to stop the machine.
⑧ Adjust button ▲:
Set indoor temperature up. If press and
hold on, it will increase at 1°C(2°F) per
0.5 second.
⑨ Adjust button ▼ :
Set indoor temperature down . if press
and hold on,it will decrease at 1°C(2°F)
per 0.5 second.
6
⑩ Swing button:
First press, start swing function;second
press, stop swing. (Match to some
model with swing function).
11 Economy operation button:
press this button, the indoor unit
operates in economy mode, press again,
exit this mode (it may be ineffective for
some models)
12 Fan speed button:
press this button consecutively, the fan
speed will circle as follow:
13 Lock button(hidden):
When you push the LOCK button, all
current settings are locked in and the
wire controller does not accept any
operation except that of the LOCK
button. Use the lock mode when you
want to prevent setting from being
changed accidentally or play fully. Push
the LOCK button again when you want
to cancel the LOCK mode.
7. USING METHOD
AUTOMATIC OPERATION
Connect to power,indoor operation lamp
flash.
1. Press "MODE" button, select " AUTO
" ;
2. Press the button "▲" and "▼", set
temperature you want, generally it is
among 17°C(62°F)~30°C(88°F);
3. Press " ON/OFF" button, operation
lamp is on, the air-conditioner work in
auto mode, indoor fan is auto, and can
not be changed. Auto is displayed on
LCD. Press ON/OFF button again to
stop.
4. Economy operation is valid in auto
mode.
COOL/HEAT/FAN MODE OPERATION
1. Press "MODE" button, select "COOL" ,
"HEAT" or "FAN ONLY" mode.
2. Press temperature adjust button to
select setting temp..
7
3. Press "FAN SPEED" button to select
high/mid/low/auto.
4. Press "ON/OFF" button, indoor unit
operation lamp on, it works in selected
mode. Press "ON/OFF" button again, it
stops to work.
Remark: When in fan mode, no
temperature can be set.
DRY OPERATION
1. Press " MODE " button, select " DRY "
mode.
2. Press temperature adjust button to
select setting temp.
3. Press " ON/OFF " button, indoor unit
operation lamp on, it works in dry mode.
Press ON/OFF button again, it stops to
work.
4. In dry mode, economy operation and
fan speed are ineffective.
2. Press " timer " on button repeatedly to
adjust time setting.
3. If press this button and hold on, the
time will increase at 0.5h, after 10h, it
increase at 1h.
4. After setting 0.5 second, the wire
controller send timer on information, it is
finished.
Timer off only:
1. Press "TIME OFF " button, it display
"SET" on LCD, and display " H " and ON,
it is waiting for timer on setting.
2. Press "TIME OFF" button repeatedly
to adjust time setting.
3. If press this button and hold on , the
time will increase at 0.5h, after 10h, it
increase at 1h.
4. After setting 0.5 second, the wire
controller send timer off information, it is
finished.
TIMER SETTING
Timer on only:
1. Press " TIME ON " button, it display
"SET" on LCD, and display " H " and
"ON" , it is waiting for timer on setting.
8
TIMER ON AND TIMER OFF BOTH
1. Set timer on time as the
corresponding step1 and 2.
2. Set timer off time as the
corresponding step1 and 2.
3. Timer off time must be longer than
timer on time.
4. 0.5 second after setting, the wire
controller send information.the setting is
finished.
CHANGE TIMER
If there is a need of changing timer
time, press corresponding button to
revise it. If concel timer, change timer
time to 0.0.
NOTE
The timer time is relative time,that is
delay after setting time( i, e: setting
time is 8:05 A,M). So when imer is set,
the standard time can not be adjusted.
8. TECHNICAL INDICATION AND REQUIREMENT
EMC and EMI comply with the CE
certification requirements.
9
Version: QSXU-002AEN
2020551A6887
20130201
Loading...