Page 1
Owner ’s Manual
The Ultimate In Style & Performance
®
21 Healey Road
Dandenong, 3175
Victoria, Australia ACN # 088 609 661
www.pridemobility.com
Page 2
SAFETY GUIDELINES
Please read and follow all instructions in this owners manual before attempting to operate your scooter for the first
time. If there is anything in this manual you do not understand, or if you require additional assistance for setup,
contact your scooter specialist.
Using your Pride product safely depends upon your diligence in following the warnings, cautions, and instructions
in this owners manual. Using your Pride product safely also depends upon your own good judgement and/or
common sense, as well as that of your provider, caregiver, and/or healthcare professional. Pride is not responsible
for injuries and/or damage resulting from any persons failure to follow the warnings, cautions, and instructions in
this owners manual. Pride is not responsible for injuries and/or damage resulting from any persons failure to
exercise good judgement and/or common sense.
The symbols below are used throughout this owners manual and/or on the scooter to identify warnings, cautions,
and important information. It is very important for you to read and understand them completely. Additional symbols
are identified in II. Safety.
WARNING! Failure to follow designated procedures can cause personal injury or component
damage or malfunction (on the scooter-black symbol on yellow triangle with black border).
PROHIBITED! These actions should be prohibited. These actions should not be performed
at any time or in any circumstances. Performing a prohibited action can cause injury to
personnel and/or damage to equipment (black symbol with red circle and red slash).
NOTE: Supplemental information that may be helpful to operate the equipment.
Copyright © 2003
Pride Mobility Products Australia Pty. Ltd.
INFMANU2438
Page 3
CONTENTS
I. INTRODUCTION ......................................................................................................................... 4
II. SAFETY ......................................................................................................................................... 6
III. SPECIFICATIONS ................................................................................................................... 17
IV. YOUR SCOOTER ...................................................................................................................... 19
V. BATTERIES AND CHARGING ............................................................................................ 23
VI. OPERATION ............................................................................................................................... 27
VII. COMFORT ADJUSTMENTS................................................................................................ 29
VIII. DISASSEMBLY AND ASSEMBLY ..................................................................................... 32
IX. OPTIONAL ACCESSORIES ................................................................................................. 35
X. BASIC TROUBLESHOOTING ............................................................................................. 36
XI. CARE AND MAINTENANCE ................................................................................................ 38
XII. WARRANTY ................................................................................................................................40
Ultimate 3-4/Rev A/July03
3
Page 4
I. INTRODUCTION
SAFETY
WELCOME
state-of-the-art components with safety, comfort, and styling in mind. We are confident that these design features
will provide you with the conveniences you expect during your daily activities. Once you understand how to safely
operate and care for your scooter, it should give you years of trouble free operation and service.
Read and follow all instructions, warnings, and notes in this manual before attempting to operate your scooter for
the first time. In addition, your safety depends upon you, as well as your Provider, caretaker, or healthcare
professional in using good judgement.
If there is any information in this manual in which you do not understand, or if you require additional assistance for
setup or operation, please contact your authorised Pride Provider. Failure to follow the instructions in this
manual and those located on your scooter can lead to personal injury and/or damage to the scooter,
including voiding the warranty.
EXPRESSED AGREEMENT OF INDEMNIFICATION
In accepting delivery of this product, the Purchaser specifically promises that s/he will not change, alter, or modify
this product or remove or render inoperable or unsafe any guards, shields, or other safety features of the product;
or remove, obliterate, or obstruct any safety and instruction signs, or fail, refuse, or neglect to install any retrofit kits
from time to time provided by Pride to enhance user safety. Purchaser also specifically agrees that if s/he breaches
any such promises, or if s/he is remiss, neglect, or deficient in the safe operation or maintenance of this product, the
purchaser will indemnify and hold harmless Pride from any and all types of actions, suits, claims, or demands,
including products liability claims by purchaser, for injuries or loss arising out of the operation, maintenance, repair,
or other use of this product. Purchaser specifically agrees that this Express Agreement of Indemnification is a
condition of sale supported by adequate consideration and was read and understood by the purchaser before
purchasing and delivery of the product.
to
Pride Mobility Products Australia Pty. Ltd.
(Pride).
The scooter you have purchased combines
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about
the safety and reliability of your new scooter, and about the service you received from your authorised Pride
Provider.
Please notify us of any change of address, so we can keep you apprised of important information about safety, new
products, and new options that can increase your ability to use and enjoy your scooter. Please feel free to contact
us at the address below:
Pride Mobility Products Australia Pty. Ltd.
21 Healey Road
Dandenong 3175
Victoria, Australia
4 Ultimate 3-4/Rev A/July03
Page 5
I. INTRODUCTION
PRIDE OWNERS CLUB
As an owner of a Pride product, you are invited to register your product's warranty and enroll in the Pride Owners
Club. You may do so by filling out and returning your enclosed product registration card or by visiting Pride's web
site at www.pridemobility.com. As a registered member, each time you visit our site, you will have access to the
most interactive and honest educational venue available today for people with mobility needs, their families, and
friends.
From our home page, select "Owners Club" to enter a page dedicated to current and potential Pride product
owners. You will gain access to interviews, stories, recreation ideas, daily living tips, product and funding information, and interactive message boards. These message boards invite you to communicate with other Pride customers as well as Pride representatives who are available to assist you with any questions or concerns you may have.
My authorised Pride Provider:
Name:_______________________________________________________________________________
Address:______________________________________________________________________________
Phone Number:_________________________________________________________________________
Purchase Date:_________________________________________________________________________
NOTE: If you ever lose or misplace your product registration card or your copy of this
manual, contact us and we will be glad to send you a new one immediately.
Ultimate 3-4/Rev A/July03
5
Page 6
II. SAFETY
PRODUCT SAFETY SYMBOLS
The symbols below are used on the scooter to identify warnings, mandatory actions, and prohibited actions. It is
very important for you to read and understand them completely.
Pinch/Crush points created during assembly.
Corrosive chemicals contained in battery. Use only AGM or Gel-Cell
batteries to reduce the risk of leakage or explosive conditions.
Read and follow the information in the owners manual.
Maximum seating weight.
Unlocked and in freewheel mode.
Place unit on level ground and stand behind or to one side when changing
from drive mode to freewheel mode or freewheel mode to drive mode.
Locked and in drive mode.
Front-to-rear plug orientation.
6 Ultimate 3-4/Rev A/July03
Page 7
II. SAFETY
Do not raise or lower the power seat while the scooter is in motion.
Do not remove anti-tip wheels.
Do not use a cell phone, walkie/talkie, laptop, or other radio transmitter while
operating.
Avoid exposure to rain, snow, ice, salt, or standing water whenever possible.
Maintain and store in a clean and dry condition.
Removal of grounding prong can create electrical hazard. If necessar y, properly
install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug
access. Failure to heed could result in personal injury and/or property damage.
Prevent personal injury and equipment damage. Do not connect an extension lead
to the AC/DC converter or the battery charger.
Ultimate 3-4/Rev A/July03
7
Page 8
II. SAFETY
GENERAL
WARNING! Do not operate your new scooter for the first time without completely reading
and understanding this owners manual.
Your scooter is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive variety of products to best fit the individual needs of the scooter user. Please be aware that the final selection
and purchasing decision regarding the type of scooter to be used is the responsibility of the scooter user who is
capable of making such a decision and his/her healthcare professional (i.e., medical doctor, physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the
scooter to the user and has assisted the prescribing healthcare professional and/or the authorised Pride Provider in
the instruction process for the use of the product.
There are certain situations, including some medical conditions, where the scooter user will need to practice
operating the scooter in the presence of a trained attendant. A trained attendant can be defined as a family member
or care professional specially trained in assisting a scooter user in various daily living activities.
As you begin using your scooter during daily activities, you will probably encounter situations in which you will
need some practice. Simply take your time and you will soon be in full and confident control as you maneuver
through doorways, on and off elevators, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help the user become accustomed to
operating the scooter safely.
MODIFICATIONS
Pride has designed and engineered your scooter to provide maximum mobility and utility. A wide range of accessories is available from your authorised Pride Provider to further customise your scooter to better suit your needs
and/or preferences. However, under no circumstances should you modify, add, remove, or disable any feature,
part, or function of your scooter.
WARNING! Do not modify your scooter in any way not authorised by Pride. Unauthorised
modifications may result in personal injury and/or damage to your scooter.
REMOVABLE PARTS
WARNING! Do not attempt to lift or move your scooter by any of its removable parts.
Personal injury and damage to the scooter may result.
ELECTROMAGNETIC FIELDS
Your scooters road performance features may be influenced by electromagnetic fields caused by cellular telephones or other radiating devices, such as hand-held radios, radio and television stations, wireless computer links,
microwave sources, and paging transmitters.
8 Ultimate 3-4/Rev A/July03
Page 9
II. SAFETY
PRE-RIDE SAFETY CHECK
Get to know the feel of your scooter and its capabilities. Pride recommends that you perform a safety check before
each use to make sure your scooter operates smoothly and safely. For details on how to perform these necessary
inspections, see XI. Care and Maintenance.
Perform the following inspections prior to using your scooter:
n Check for proper tyre inflation (if equipped with pneumatic tyres).
n Check all electrical connections. Make sure they are tight and not corroded.
n Check all harness connections. Make sure they are secured properly.
n Check the brakes.
n Check battery charge.
If you discover a problem, contact your authorised Pride Provider for assistance.
TYRE INFLATION
If your scooter is equipped with pneumatic tyres, you should check or have the air pressure checked at least once
a week. Proper inflation pressures will prolong the life of your tyres and help ensure the smooth operation of your
scooter.
WARNING! It is critically important that 2-2.4 bar (30-35 psi) tyre pressure be maintained
in pneumatic tyres at all times. Do not underinflate or overinflate your tyres. Low pressure
may result in loss of control, and overinflated tyres may burst. Failure to maintain 2-2.4
bar (30-35 psi) tyre pressure in pneumatic tyres at all times may result in tyre and/or wheel
failure, causing serious personal injury and/or damage to your scooter.
WARNING! Inflate your scooter tyres from a regulated air source with an available pressure
gauge. Inflating your tyres from an unregulated air source could overinflate them, resulting
in a burst tyre and/or personal injury.
WEIGHT LIMIT ATIONS
Your scooter is rated for a maximum weight capacity. Refer to the specifications table for information.
WARNING! Exceeding the weight capacity voids your warranty and may result in personal
injury and damage to your scooter. Pride will not be held responsible for injuries and/or
property damage resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your scooter. Carrying passengers may result in
personal injury and/or proper ty damage.
INCLINE INFORMATION
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access.
Some ramps may have turning switchbacks (180-degree turns) that require you to have good cornering skills on
your scooter.
n Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
n Take wide swings with your scooter around any tight corners. If you do that, the scooters rear wheels will
follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.
n When driving down a ramp, keep the scooters speed adjustment set to the slowest speed setting to ensure a
safely controlled descent.
n Avoid sudden stops and starts.
Ultimate 3-4/Rev A/July03
9
Page 10
II. SAFETY
10.5%
12.3%
14.1%15.8%
68 kg
113 kg
136-159 kg
90 kg
When climbing an incline, try to keep your scooter moving. If you must stop, start up again slowly, and then
accelerate cautiously. When driving down an incline, do so by setting the speed adjustment dial to the slowest
setting and driving in the forward direction only. If your scooter starts to move down the incline faster than you
anticipated or desired, allow it to come to a complete stop by releasing the throttle control lever. Then push the
throttle control lever forward slightly to ensure a safely controlled descent.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of the
incline. Drive your scooter straight up the incline. This greatly reduces the possibility of a
tip or a fall. Always exercise extreme caution when negotiating an incline.
WARNING! Do not drive your scooter across the side of a hill or diagonally up or down a
hill; do not stop, if possible, while driving up or down an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas
covered with snow, ice, cut grass, or wet leaves).
WARNING! When on any sort of an incline or decline, never place the scooter in freewheel
mode while seated on it or standing next to it.
WARNING! Even though your scooter is capable of climbing slopes greater than those
illustrated in figures 1 and 1A, do not, under any circumstances, exceed the incline
guidelines or any other specifications presented in this manual. Doing so could cause
instability in your scooter, resulting in personal injury and/or damage to your scooter.
Handicap public access ramps are not subject to government regulation in all countries, and therefore do not
necessarily share the same standard percent of slope. Other inclines may be natural or, if man-made, not designed
specifically for scooters. Figures 1 and 1A illustrate your scooters stability and its ability to climb grades under
various weight loads and under controlled testing conditions.
These tests were conducted with the scooters seat in the highest position and adjusted rearward on the seat base
to its farthest rearward position. Use this information as a guideline. Your scooters ability to travel up inclines is
affected by your weight, your scooters speed, your angle of approach to the incline, and your scooter setup.
68 kg
14.1%
Figure 1. (3-wheel) Maximum Recommended
Incline Angles
WARNING! Any attempt to climb or descend a slope steeper than what is shown in figures
1 and 1A may put your scooter in an unstable position and cause it to tip, resulting in
personal injury.
90 kg
12.3%
113 kg
10.5%
136-159 kg
8.7%
Figure 1A. (4-wheel) Maximum Recommended
Incline Angles
WARNING! Never carry an oxygen tank weighing more than 7 kg. Never fill the rear
basket with contents exceeding 7 kg.
10 Ultimate 3-4/Rev A/July03
Page 11
II. SAFETY
When you approach an incline, it is best to lean forward. See figures 2 and 2A. This shifts the center of gravity of
you and your scooter toward the front of the scooter for improved stability.
Figure 2. Normal Driving Position
Figure 2A. Increased Stability Driving Position
CORNERING INFORMATION
Excessively high cornering speeds can create the possibility of tipping. Factors which affect the possibility of
tipping include, but are not limited to, cornering speed, steering angle (how sharply you are turning), uneven road
surfaces, inclined road surfaces, riding from an area of low traction to an area of high traction (such as passing from
a grassy area to a paved area especially at high speed while turning), and abrupt directional changes. High
cornering speeds are not recommended. If you feel that you may tip over in a corner, reduce your speed and
steering angle (i.e., lessen the sharpness of the turn) to prevent your scooter from tipping.
WARNING! When cornering sharply, reduce your speed. When using your scooter at higher
speeds, do not corner sharply. This greatly reduces the possibility of a tip or fall. To avoid
personal injury or property damage, always exercise common sense when cornering.
BRAKING INFORMATION
Your scooter is equipped with these powerful brake systems:
1. Regenerative: Uses electricity to rapidly slow the vehicle when the throttle control lever returns to the center/
stop position.
2. Disc Park Brake: Activates mechanically after regenerative braking slows the vehicle to near stop, or when
power is removed from the system for any reason.
Ultimate 3-4/Rev A/July03
11
Page 12
II. SAFETY
OUTDOOR DRIVING SURFACES
Your scooter is designed to provide optimum stability under normal driving conditionsdry, level surfaces composed of concrete, blacktop, or asphalt. However, Pride recognises that there will be times when you will encounter other surface types. For this reason, your scooter is designed to perform admirably on packed soil, grass, and
gravel. Feel free to use your scooter safely on lawns and in park areas.
n Reduce your scooters speed when driving on uneven terrain and/or soft surfaces.
n Avoid tall grass that can become tangled in the running gear.
n Avoid loosely packed gravel and sand.
n If you feel unsure about a driving surface, avoid that surface.
STREETS AND ROADWAYS
WARNING! You should not operate your scooter on public streets and roadways. Be aware
that it may be difficult for traffic to see you when you are seated on your scooter. Obey all
local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with
extreme caution.
NOTE: Safety accessories like fluorescent flags are available to order from your authorised
Pride Provider.
STATIONARY OBSTACLES (STEPS, KERBS, ETC.)
WARNING! Do not drive near raised surfaces, unprotected ledges, and/or drop-offs (kerbs,
porches, stairs, etc.).
WARNING! Do not attempt to have your scooter climb or descend an obstacle that is
inordinately high. Serious personal injur y and/or damage may result.
WARNING! Do not attempt to have your scooter proceed rearward down any step, kerb, or
other obstacle. This may cause the scooter to tip and cause personal injury.
WARNING! Be sure your scooter is traveling perpendicular to any kerb you may be required
to ascend or descend. See figures 3 and 3A.
WARNING! Do not attempt to negotiate a kerb that has a height greater than 5 cm.
KERB
KERB
Figure 3. Correct Kerb Approach Figure 3A. Incorrect Kerb Approach
12 Ultimate 3-4/Rev A/July03
Page 13
II. SAFETY
INCLEMENT WEATHER PRECAUTIONS
WARNING! Pride recommends that you do not operate your scooter in icy or slippery
conditions or on salted surfaces (i.e., walks or roads). Such use may result in an accident,
personal injury, or adversely affect the performance and safety of your scooter.
WARNING! Do not operate or store your scooter where it may be exposed to inclement
weather conditions such as rain, snow, mist, and below freezing temperatures (such as
storage on an outside car/van lift). Attempting to operate the scooter in such conditions
can damage the electronics and potentially result in loss of control.
FREEWHEEL MODE
Your scooter is equipped with a manual freewheel lever that, when pulled up, allows the scooter to be pushed. For
more information about how to place your scooter into and out of freewheel mode, see IV. Your Scooter.
WARNING! When your scooter is in manual freewheel mode, the braking system is
disengaged.
n Disengage the drive motors only on a level surface.
n Ensure the key is removed from the key switch.
n Stand behind the scooter to engage or disengage freewheel mode. Never sit on a
scooter to do this.
n After you have finished pushing your scooter, always return it to the drive mode to lock
the brakes.
Failure to heed the above could result in personal injury and/or damage to your scooter.
An added feature built into the Ultimate 3-4 is push-too-fast protection which safeguards the scooter against
gaining excessive speed while in freewheel mode.
Push-too-fast operates differently depending on which of two conditions exists:
n If the key is switched off while in freewheel mode, the scooters controller activates regenerative braking
when the scooter is pushed faster than a maximum threshold which has been preprogrammed. In this case, the
controller is acting as a speed governor.
n If the key is switched on while in freewheel mode, you will encounter considerable resistance at any speed.
This prevents the scooter from gaining unwanted momentum should the manual freewheel lever inadvertently
be released while driving the scooter.
Ultimate 3-4/Rev A/July03
13
Page 14
II. SAFETY
STAIRS AND ESCALATORS
Scooters are not designed to travel up or down stairs or escalators. Always use an elevator.
WARNING! Do not use your scooter to negotiate steps or escalators. You may cause injury
to yourself and to others and/or damage your scooter.
DOORS
n Determine if the door opens toward or away from you.
n Use your hand to turn the knob or push the handle or push-bar.
n Drive your scooter gently and slowly forward to push the door open. Or drive your scooter gently and slowly
rearwards to pull the door open.
ELEVATORS
Modern elevators have a door edge safety mechanism that, when pushed, reopens the door(s).
n If you are in the doorway of a elevator when the door(s) begin to close, push on the rubber door edge or allow
the rubber door edge to contact the scooter and the door will reopen.
n Use care that pocketbooks, packages, or scooter accessories do not become caught in elevator doors.
NOTE: If your scooters turning radius is greater than 150 cm, it may be difficult to maneuver
in elevators and building entrances. Use caution when attempting to turn or maneuver
your scooter in small spaces, and avoid areas that might pose a problem.
LIFT/ELEVATION PRODUCTS
If you will be traveling with your scooter, you may find it necessary to use a lift/elevation product to aid in transportation. Pride recommends that you closely review the instructions, specifications, and safety information set forth
by the manufacturer of the lift/elevation product before using that product.
WARNING! Never sit on your scooter when it is being used in connection with any type of
lift/elevation product. Your scooter was not designed with such use in mind, and any
damage or injury incurred from such use is not the responsibility of Pride.
BATTERIES
In addition to following the warnings below, be sure to comply with all other battery handling information.
WARNING! Scooter batteries are heavy (refer to specifications table). Lifting weight
beyond your capacity could result in personal injury. If necessary, get someone physically
able to lift the scooters batteries for you.
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wash hands after handling.
WARNING! Always protect the batteries from freezing and never charge a frozen battery.
Charging a frozen battery may result in personal injury and/or damage to the battery.
WARNING! RED (+) cables must be connected to positive (+) battery terminals/posts. BLACK
(-) cables must be connected to negative (-) battery terminals/posts. Failure to connect
your battery harnesses in the proper manner may result in personal injury and/or damage
to your scooter. REPLACE cables immediately if damaged.
14 Ultimate 3-4/Rev A/July03
Page 15
II. SAFETY
BATTERY DISPOSAL AND RECYCLING
If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag and call your authorised
Pride Provider for instructions on disposal. Your authorised Pride Provider will also have the necessary information on battery recycling, which is our recommended course of action.
MOTOR VEHICLE TRANSPORT
Currently, there are no standards approved for tie-down systems in a moving vehicle of any type to transport a
person while seated in a scooter.
Although your scooter may be equipped with a positioning belt, this belt is not designed to provide proper restraint
during motor vehicle transport. Anyone traveling in a motor vehicle should be properly secured in the motor vehicle
seat with safety belts fastened securely.
WARNING! Do not sit on your scooter while it is in a moving vehicle. Personal injury and/or
property damage may result.
WARNING! Always be sure your scooter and its batteries are properly secured when it is
being transported. Failure to do so may result in personal injury and/or damage to your
scooter.
PREVENTING UNINTENDED MOVEMENT
WARNING! If you anticipate being seated in a stationary position for an extended period
of time, turn off the power. This will prevent unexpected motion from inadvertent throttle
control lever contact. Failure to do so may result in personal injury.
GETTING ONTO AND OFF OF YOUR SCOOTER
Getting onto and off of your scooter requires a good sense of balance. Please observe the following safety tips
when getting onto and off of your scooter:
n Ensure that your scooter is not in freewheel mode. See IV. Your Scooter.
n Make certain that the seat is locked into place and the key is removed from the key switch.
n The seat armrests can be flipped up to make getting onto and off of the scooter easier.
WARNING! Position yourself as far back as possible in the scooter seat to prevent the
scooter from tipping and causing injury.
WARNING! Avoid using your armrests for weight bearing purposes. Such use may cause
the scooter to tip and cause personal injury.
WARNING! Avoid putting all of your weight on the floorboard. Such use may cause the
scooter to tip and cause personal injury.
Ultimate 3-4/Rev A/July03
15
Page 16
II. SAFETY
REACHING AND BENDING
Avoid reaching or bending while driving your scooter. When reaching, bending, or leaning while seated on your
scooter, it is important to maintain a stable center of gravity and keep the scooter from tipping. Pride recommends
that the scooter user determine his/her personal limitations and practice bending and reaching in the presence of a
qualified healthcare professional.
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the
floor by reaching down between your knees. Movements such as these may change your
center of gravity and the weight distribution of the scooter and cause your scooter to tip,
possibly resulting in personal injury. Keep your hands away from the tyres when driving.
POSITIONING BELTS
Your authorised Pride Provider, therapist(s), and other healthcare professionals are responsible for determining
your requirement for a positioning belt in order to operate your scooter safely.
WARNING! If you require a positioning belt to safely operate your scooter, make sure it is
fastened securely. Serious personal injury may result if you fall from the scooter.
PRESCRIPTION DRUGS/PHYSICAL LIMITATIONS
The scooter user must exercise care and common sense when operating his/her scooter. This includes awareness of
safety issues when taking prescribed or over-the-counter drugs or when the user has specific physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter
medication or if you have certain physical limitations. Some medications and limitations
may impair your ability to operate your scooter in a safe manner.
ALCOHOL
The scooter user must exercise care and common sense when operating his/her scooter. This includes awareness
of safety issues while under the influence of alcohol.
WARNING! Do not operate your scooter while you are under the influence of alcohol, as
this may impair your ability to drive safely.
16 Ultimate 3-4/Rev A/July03
Page 17
III. SPECIFICATIONS
50 cm
101.6 cm-111.7 cm
43cm - 53cm
8 cm
3-wheel 104 cm
Figure 4. Scooter Dimensions
25 cm
Figure 4A. Front Tyre Dimensions
8 cm
18"
16"
50 cm
61 cm
61 cm
45 cm
3-wheel 115.5 cm
4-wheel 119 cm
4-wheel 147 cm
Length
Turning Radius
25 cm
Figure 4B. Rear T yre Dimensions
10 cm
Ultimate 3-4/Rev A/July03
17
Page 18
III. SPECIFICATIONS
Model Numbers 3-wheel: CF3000AUS
4-wheel: CF3400AUS
Available Colours Painted: Red, Blue, Champagne, Black
Overall Length 3-wheel: 115.5 cm
4-wheel: 119 cm
Overall Width 61 cm
Total Weight Without Batteries 3-wheel: 72 kg
4-wheel: 73 kg
Heaviest Piece When Disassembled Rear frame: 26 kg
Turning Radius 3-wheel: 104 cm
4-wheel: 147 cm
Speed (Maximum) Variable up 9.25 km/h
Range Per Charge* (With 32 AH batteries) Up to 40 km
Ground Clearance 8 cm
Weight Capacity 159 kg
Standard Seating Type: High Back with headrest and sliders
Material: Gray vinyl
Dimensions: 50 cm width
45 cm depth (usable)
50 cm height (usable)
Drive System Rear-wheel drive, sealed transaxle with a 24-volt DC motor
Dual Braking System Electronic, regenerative, and electromechanical
Wheels Aluminum alloy wheels in Black
Tyres Pneumatic: front: 8 cm x 25 cm
rear: 10 cm x 25 cm
Battery Requirements Two 12-volt deep cycle (AGM or Gel-Cell)
Size: (U-1) 32 AH
Battery Charger Onboard, 3-amp, 220 volt charger
* Varies with user weight, terrain type, battery charge, battery condition, and tyre condition.
18 Ultimate 3-4/Rev A/July03
Page 19
IV. YOUR SCOOTER
TILLER CONSOLE
The tiller console houses all of the controls needed to drive your scooter, including the speed adjustment dial, throttle
control levers, battery condition meter, lights switch, hazard lights switch, turn signal buttons, on/off indicator LED,
and horn buttons. See figure 5.
WARNING! Do not expose the tiller console to moisture. In the event that the tiller console
does become exposed to moisture, do not attempt to operate your scooter until the tiller
console has dried thoroughly.
BA TTERY CONDITION METER
KEY SWITCH
HORN BUTTON
LIGHTS SWITCH
TURN SIGNAL BUTTON (LEFT)
THROTTLE CONTROL LEVER
(REVERSE)
Figure 5. Tiller Console
SPEED ADJUSTMENT DIAL
HAZARD LIGHTS SWITCH
POWER SEA T SWITCH
TURN SIGNAL BUTTON (RIGHT)
THROTTLE CONTROL LEVER
ST ATUS LED
HORN BUTTON
(FORWARD)
Key Switch
n Insert the key into the key switch and turn it clockwise to power up (turn on) your scooter.
n Turn the key anticlockwise to power down (turn off) your scooter.
WARNING! If the key is turned to the off position while your scooter is in motion, the
electronic brakes engage and your scooter will come to an abrupt stop!
Throttle Control Levers
These levers allow you to control the forward speed and the reverse speed of your scooter up to the maximum
speed you preset with the speed adjustment dial.
n Place your right hand on the right handgrip and your left hand on the left handgrip.
n Use your right thumb to push the right side of the throttle control lever to disengage your scooters brakes and
move forward.
n Release the throttle control lever and allow your scooter to come to a complete stop before pushing the other
side of the lever to move in reverse.
n When the throttle control lever is completely released, it automatically returns to the center stop position and
engages your scooters brakes.
Speed Adjustment Dial
This dial allows you to preselect and limit your scooters top speed.
n The image of the tortoise represents the slowest speed setting.
n The image of the hare represents the fastest speed setting.
Ultimate 3-4/Rev A/July03
19
Page 20
IV. YOUR SCOOTER
Lights Switch
This three-position switch controls your scooters front (upper), front (lower), and rear running lights.
n Toggle the switch forward to turn on your scooters running lights and front (upper) light on.
n When the toggle switch is in the middle position, your scooter lights are off.
n Toggle the switch rearward to turn on all your scooter lights, including the front (lower) light.
Horn Buttons
Your scooter must be turned on for the horn to be operational.
n These buttons activate a warning horn.
n Do not hesitate to use the warning horn when doing so may prevent accident or injury.
Hazard Lights Switch
This switch activates the 4-way flashers on your scooter.
n Toggle the switch forward to turn on the flashers.
n Toggle the switch rearward to turn off the flashers.
Turn Signal Buttons
n Press the appropriate turn signal button once to activate it.
n Your scooters turn indicators are timed to shut off automatically.
Status LED
The Status LED will alert you to electrical problems that may occur with your scooter. The LED remains constantly lit
while your scooter is on. If your scooter develops an electrical problem, the status LED will flash a code. See X. Basic
Troubleshooting.
TILLER CONSOLE FUSES
These fuses help protect your scooters front lighting, turn indicators, and key switch console systems from
receiving an overload of electrical current. The fuses used in your scooter are the same type used in automobiles.
See XI. Care and Maintenance for fuse replacement.
3-AMP KEY SWITCH FUSE
3-AMP RIGHT SIDE RUNNING
LIGHTS FUSE
3-AMP LEFT SIDE RUNNING
LIGHTS FUSE
3-AMP LEFT TURN SIGNAL FUSE
3-AMP RIGHT TURN SIGNAL FUSE
Figure 5A. Tiller Console Fuses
20 Ultimate 3-4/Rev A/July03
Page 21
IV. YOUR SCOOTER
REAR SECTION
The onboard battery charger (not shown), the charger power lead receptacle, the batteries (not shown), the main
circuit breaker (reset button), the ammeter, the manual freewheel lever, the anti-tip wheels, and the motor/transaxle
assembly are located on the rear section of your scooter. See figure 6.
CHARGER POWER LEAD
RECEPTACLE
AMMETER
MAIN CIRCUIT BREAKER
(RESET BUTTON)
MOTOR/TRANSAXLE
ASSEMBLY
ANTI-TIP WHEEL
Figure 6. Rear Section
MANUAL FREEWHEEL
LEVER
ANTI-TIP WHEEL
Charger Power Lead Receptacle
The charger power lead plugs into your scooters battery charger by means of the charger power lead receptacle.
Ammeter
During charging, the ammeter indicates the charging rate, or how hard the charger is working to charge the scooters
batteries. See V. Batteries and Charging.
Main Circuit Breaker (Reset Button)
When the voltage in your scooters batteries becomes low or the scooter is heavily strained because of excessive
loads or steep inclines, the main circuit breaker may trip to protect the motor and electronics from damage. See
figure 6.
n The main circuit breaker reset button pops out when the breaker trips.
n When the breaker trips, the entire electrical system of your scooter shuts down.
n Allow a minute or two for your scooters electronics to rest.
n Push in the reset button to reset the main circuit breaker.
n If the main circuit breaker trips frequently, you may need to charge your batteries more often. You may also
need to have your authorised Pride Provider perform a load test on your scooters batteries.
n If the main circuit breaker trips repeatedly, see your authorised Pride Provider for service.
Ultimate 3-4/Rev A/July03
21
Page 22
IV. YOUR SCOOTER
Manual Freewheel Lever
Whenever you need or want to push your scooter for short distances, you can put it in freewheel mode.
n The manual freewheel lever is located on the end of the motor/transaxle assembly at the right rear of the
scooter. See figure 6.
n Remove the key from the key switch.
n Pull up on the manual freewheel lever to disable the drive system and the brake system.
n You may now push your scooter.
n Push down on the manual freewheel lever to reengage the drive and the brake systems and take your scooter out
of freewheel mode.
WARNING! When your scooter is in freewheel mode, the braking system is disengaged.
n Disengage the drive motors only on a level surface.
n Ensure the key is removed from the key switch.
n Stand behind the scooter to engage or disengage freewheel mode. Never sit on a
scooter to do this.
n After you have finished pushing your scooter, always return it to the drive mode to lock
the brakes.
Failure to heed the above could result in personal injury and/or damage to your scooter.
NOTE: If the scooter is placed in freewheel mode (manual freewheel lever pulled up)
while the key is in the on position, the scooter will not run until the manual freewheel
lever is pushed down and the key is turned to the off position, then back to the on
position.
Batteries (Not Shown)
The batteries store electrical energy that powers your scooter. See V. Batteries and Charging.
Anti-Tip Wheels
The anti-tip wheels are an integral and important safety feature of your scooter. Do not, under any circumstances,
remove the anti-tip wheels from your scooter.
WARNING! Do not remove the anti-tip wheels or modify your scooter in any way that is not
authorised by Pride.
Motor/T ransaxle Assembly
The motor/transaxle assembly is an electromechanical unit that converts electrical energy from your scooters
batteries into the controlled mechanical energy that drives the scooters wheels.
22 Ultimate 3-4/Rev A/July03
Page 23
V. BATTERIES AND CHARGING
Your scooter requires two sealed, maintenance free, 12-volt, deep cycle batteries.
n Charge the batteries prior to using your scooter for the first time.
n Keep the batteries fully charged to keep your scooter running smoothly.
READING YOUR BA TTERY VOL T AGE
The battery condition meter on the tiller console indicates the approximate strength of your batteries using a colour
code. Green indicates fully charged batteries, yellow indicates a draining charge, and red indicates that an immediate recharge is necessary. See figure 7. To check the charge, you must first unplug the charger power lead and
power up your scooter. To ensure the highest accuracy, the battery condition meter should be checked while
operating your scooter at full speed on a dry, level surface.
You can also check the charge using the ammeter located on the rear of the scooter. The charger power lead must
be plugged into a standard wall outlet in order to obtain a reading. When the amperage reading is at or near zero
amps, the battery charging is complete. See figure 8.
Figure 7. Battery Condition Meter
Figure 8. Ammeter Indicates
Battery Is Fully Charged
CHARGING YOUR BATTERIES
WARNING! Never use an extension lead to plug in your battery charger. Plug the charger
directly into a properly wired standard wall outlet.
Follow these easy steps to charge your batteries safely:
1. Position your scooter close to a standard wall outlet.
2. Remove the key from the key switch.
3. Make certain that the manual freewheel lever is in the drive (down) position.
4. Plug the charger power lead into the charger power lead receptacle.
5. Extend the charger power lead and plug it into the wall outlet. It is recommended that you charge your
batteries for 8 to 14 hours.
6. When the batteries are fully charged, unplug the charger power lead from the wall outlet and then from the
charger power lead receptacle.
NOTE: There is a charger inhibit function on your scooter. The scooter will not run and
the battery condition meter will not operate while the batteries are charging.
Ultimate 3-4/Rev A/July03
23
Page 24
V. BATTERIES AND CHARGING
FREQUENTLY ASKED QUESTIONS (FAQS)
How does the charger work?
When your scooters battery voltage is low, the charger works harder and sends more electrical current to the
batteries to bring up their charge. As the voltage of the batteries approaches a full charge, the charger sends less
and less electrical current to the batteries. When the batteries are fully charged, the current sent to them from the
charger is at nearly zero amperage. Therefore, when the charger is plugged in, it maintains the charge on your
scooters batteries, but does not overcharge them. We do not recommend that you charge your scooters batteries
for more than 24 consecutive hours.
What if the scooters batteries wont charge?
n Be sure the battery cables are connected properly.
n Ensure both ends of the charger lead are inserted fully.
Can I use a different charger?
For the safest, most efficient, and balanced charging of your scooters batteries, we prefer and highly recommend
the simultaneous charging of both batteries by use of the onboard battery charger.
How often must I charge the batteries?
Two major factors must be considered when deciding how often to charge your scooters batteries:
n All day scooter use on a daily basis.
n Infrequent or sporadic scooter use.
With these considerations in mind, you can determine just how often and for how long you should charge your
scooters batteries. We designed the onboard charger so that it will not overcharge your scooters batteries (do
not charge them for more than 24 consecutive hours). However, you may encounter some problems if you do not
charge your batteries often enough and if you do not charge them on a regular basis. Following the guidelines below
will provide safe and reliable battery operation and charging.
n If you use your scooter daily, charge its batteries as soon as you finish using it for the day. Your scooter will be
ready each morning to give you a full day of service. We recommend that you charge your scooters batteries
for 8 to 14 hours after daily use.
n If you use your scooter once a week or less, charge its batteries at least once a week for 12 to 14 hours at a time.
n Keep your scooters batteries fully charged.
n Avoid deeply discharging your scooters batteries.
n Do not charge your scooters batteries for more than 24 consecutive hours.
Why do my new batteries seem weak?
Deep-cycle batteries employ a different chemical technology than that used in car batteries, nickel-cadmium batteries
(nicads), or in other common battery types. Deep-cycle batteries are specifically designed to provide power, drain
down their charge, and then accept a relatively quick recharge.
What about public transportation?
If you intend to use public transportation while using your scooter, you must contact in advance the transportation
provider to determine their specific requirements.
24 Ultimate 3-4/Rev A/July03
Page 25
V. BATTERIES AND CHARGING
How can I get maximum range or distance per charge?
Rarely will you have ideal driving conditions smooth, flat, hard driving surfaces with no wind or curves. Often,
you will face hills, footpath cracks, uneven and loosely packed surfaces, curves, and wind. All of these driving
conditions affect the distance or running time per battery charge. The following are a few suggestions for obtaining
the maximum range per battery charge.
n Always fully charge the batteries prior to your daily use.
n Maintain 2-2.4 bar (30-35 psi) in all of your scooter tyres.
n Plan your route to avoid as many hills, cracked, broken, or soft surfaces as possible.
n Limit your baggage weight to essential items.
n Try to maintain an even speed while your scooter is in motion.
n Avoid stop-and-go driving.
What type and size of battery should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are deep-cycle
batteries that are similar in performance. Do not use wet-cell batteries, which have removable caps.
WARNING! Corrosive chemicals contained in batteries. Use only AGM or Gel-Cell batteries
to reduce the risk of leakage or explosive conditions.
NOTE: Sealed batteries are not serviceable. Do not remove the caps.
Use these specifications to reorder deep-cycle batteries:
Type: Deep-cycle (AGM or Gel-Cell)
Size: U-1
Voltage: 12 volts each
Amperage: 32 AH (amp hours)
To change a battery in your scooter:
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wash hands after handling.
1. Remove the seat and the rear shroud. See VIII. Disassembly and Assembly.
2. Disconnect the battery strap.
3. Disconnect the 2-pin, black and white battery harness from its mating plug. See VIII. Disassembly and Assembly.
4. Disconnect the battery cables from the battery terminals.
5. Remove the old battery.
6. Place a new battery in the battery well.
7. Connect the red battery cable to the positive (+) battery terminal.
8. Connect the black battery cable to the negative (-) battery terminal.
9. Reconnect the 2-pin, black and white battery harness to its mating plug.
10. Reconnect the battery strap.
11. Reinstall the rear shroud and seat.
Ultimate 3-4/Rev A/July03
25
Page 26
V. BATTERIES AND CHARGING
BATTERY DISPOSAL AND RECYCLING
If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag and call your authorised
Pride Provider for instructions on disposal. Your authorised Pride Provider will also have the necessary information on battery recycling, which is our recommended course of action.
We work closely with our battery manufacturer to provide batteries that best suit your scooters specific electrical
demands. Fresh batteries arrive daily at Pride and are shipped fully charged to our customers. During shipping, the
batteries may encounter temperature extremes that may influence their initial performance. Heat diminishes the
charge on the battery; cold slows the available power and extends the time needed to recharge the battery.
It may take a few days for the temperature of your scooters batteries to stabilise and adjust to their new room or
ambient temperature.
More importantly, it takes a few charging cycles (a partial drain followed by a full recharge) to establish the critical
chemical balance that is essential to a deep-cycle batterys peak performance and long life.
Please follow these steps to properly break in your scooters new batteries for maximum efficiency and service life.
1. Fully recharge any new battery prior to its initial use. This charging cycle brings the battery up to about 88% of
its peak performance level.
2. Operate your new scooter in familiar and safe areas. Drive slowly at first, and do not travel too far from your
home or familiar surroundings until you have become accustomed to your scooters controls and have properly
broken in your scooters batteries.
3. Fully recharge the batteries. They should be at over 90% of their peak performance level.
4. Operate your scooter again.
5. Fully recharge the batteries again.
6. After four or five charging cycles, the batteries are able to receive a charge of 100% of their peak performance
level and are able to last for an extended period of time.
How can I ensure maximum battery life?
Fully charged deep-cycle batteries provide reliable performance and extended battery life. Keep your scooters
batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently charged,
or stored without a full charge may be permanently damaged, causing unreliable performance and limited service life.
How should I store my scooter and its batteries?
See XI. Care and Maintenance.
26 Ultimate 3-4/Rev A/July03
Page 27
VI. OPERATION
BEFORE GETTING ONTO YOUR SCOOTER
n Have you fully charged the batteries? See V. Batteries and Charging.
n Is the manual freewheel lever in the drive (down) position? Never leave the manual freewheel lever pulled up
unless you are manually pushing your scooter.
GETTING ONTO YOUR SCOOTER
1. Make certain that the key is removed from the key switch.
WARNING! Never attempt to board or exit your scooter without first removing the key
from the key switch. This will prevent the scooter from moving if accidental throttle
control lever contact is made.
2. Stand at the side of your scooter.
3. Disengage the seat lock lever and rotate the seat until it is facing you.
4. Make certain that the seat is locked securely in position.
5. Position yourself comfortably and securely in the seat.
6. Disengage the seat lock lever and rotate the seat until you are facing forward.
7. Make certain that the seat is locked securely in position.
8. Make certain that your feet are safely on the floorboard.
PRE-RIDE ADJUSTMENTS AND CHECKS
n Is the seat at the proper height? See VII. Comfort Adjustments.
n Is the seat locked securely in place?
n Is the tiller at a comfortable setting and locked securely in place? See VII. Comfort Adjustments.
n Is the key fully inserted into the key switch and turned clockwise to the on position?
n Does the scooters horn work properly?
n Is your proposed path clear of people, pets, and obstacles?
n Have you planned your route to avoid adverse terrain and as many inclines as possible?
OPERA TING YOUR SCOOTER
Keep both hands on the tiller and your feet on the floorboard at all times while operating your scooter. This driving
position gives you the most control over your vehicle.
n Set the speed adjustment dial to your desired speed.
n Press your thumb against the appropriate throttle control lever.
n The electromechanical disc park brake automatically disengages and the scooter accelerates smoothly to the
speed you preselected with the speed adjustment dial.
n Pull on the left handgrip to steer your scooter to the left.
n Pull on the right handgrip to steer your scooter to the right.
n Move the tiller to the center position to drive straight ahead.
n To stop, slowly release the throttle control lever. The electronic brakes will automatically engage when your
scooter comes to a stop.
NOTE: Your scooters reverse speed is slower than that of the forward speed you preset
with the speed adjustment dial.
Ultimate 3-4/Rev A/July03
27
Page 28
VI. OPERATION
GETTING OFF OF YOUR SCOOTER
1. Bring your scooter to a complete stop.
2. Remove the key from the key switch.
3. Disengage the seat lock lever and rotate the seat until you are facing toward the side of your scooter.
4. Make certain that the seat is locked securely in position.
5. Carefully and safely get out of the seat and stand to the side of your scooter.
6. You can leave the seat facing to the side to facilitate boarding your scooter next time.
POWER DOWN TIMER FEA TURE
Your scooter is equipped with an energy saving automatic power down timer feature designed to preserve your
scooters battery life. If you mistakenly leave the key in the key switch and in the on position but do not use your
scooter for approximately 20 minutes, the scooters controller shuts down automatically. Although the controller is
shut down, power will still be supplied to the scooters lighting system.
If the power down timer feature takes effect, perform the following steps to resume normal operation.
1. Remove the key from the key switch.
2. Reinsert the key and power up your scooter.
28 Ultimate 3-4/Rev A/July03
Page 29
VII. COMFORT ADJUSTMENTS
WARNING! Remove the key from the key switch before adjusting the tiller or the seat.
Never attempt to adjust the tiller or the seat while the scooter is in motion.
TILLER ANGLE ADJUSTMENT
Your scooter is equipped with a pivoting tiller that allows
adjustment to several positions from the scooter deck to
the farthest forward stop.
1. Lift the tiller adjustment lever. See figure 9.
2. Move the tiller to a comfortable position.
3. Release the tiller adjustment lever to secure the tiller
in position.
SEAT ROTATION
The seat lock lever will lock the seat into several positions.
1. Push forward on the seat lock lever to unlock the
seat. See figure 10.
2. Rotate the seat to the desired position.
3. Pull back firmly on the seat lock lever to lock the
seat securely in place.
TILLER
ADJUSTMENT
LEVER
Figure 9. Tiller Adjustment
FRONT-TO-BACK SEAT ADJUSTMENT
You can reposition the scooters seat forward or
rearward to adjust the distance between the seat
and the tiller. See figure 10.
1. Move the seat sliding lever outward.
2. While holding the lever out, slide the seat forward or
rearward.
3. Release the seat sliding lever once the seat is in the
desired position.
SEA T SLIDING LEVER
SEAT LOCK LEVER
Figure 10. Seat Adjustments
Ultimate 3-4/Rev A/July03
29
Page 30
VII. COMFORT ADJUSTMENTS
SEATBACK ADJUSTMENT
WARNING! Do not operate your
scooter with the seatback in a
reclined position.
WARNING! Always keep your back
pressed firmly against the seatback
while adjusting the angle.
To adjust your scooter's reclining seat, perform these steps.
See figure 11.
1. With your back pressed up against the seatback, lift
up on the seatback adjustment lever and lean forward
or rearward to adjust the seatback angle.
2. Release the seatback adjustment lever once the seat
is in a comfortable riding position.
ARMREST ANGLE ADJUSTMENT
The armrest angle of your scooter can be adjusted upward or downward by turning the adjustment dial. See
figure 11A.
NOTE: The armrests also pivot
upward to make getting on and off
of your scooter easier.
SEAT HEIGHT ADJUSTMENT
You can change the seat height to one of three positions
in 2.5 cm increments. See figure 12.
Changing the seat height:
1. Turn the scooter off and place the manual freewheel
lever in drive mode.
2. Lift the seat up and out of the seat post.
3. Loosen and remove the seat height adjustment bolt
,bolt-nut, and washers.
4. Slide the upper seat post up or down in the lower
seat post.
5. Align the adjustment holes of the upper seat post and
the lower seat post.
6. Reinstall the seat height adjustment bolt, bolt-nut,
and washers, then tighten.
7. Reinstall the shroud.
8. Reinstall and lock the seat into place.
SEATBACK ADJUSTMENT
LEVER
Figure 11. Seatback Adjustment
ADJUSTMENT DIAL
Figure 11A. Armrest Angle Adjustment
WASHER
BOL T -NUT
ADJUSTMENT BOLT
UPPER SEAT POST
WASHER
SEA T HEIGHT
LOWER SEAT POST
30 Ultimate 3-4/Rev A/July03
Figure 12. Seat Height Adjustment
Page 31
VII. COMFORT ADJUSTMENTS
POWER SEAT (OPTIONAL)
Your scooter may be equipped with a power seat. The power seat actuator is designed to raise or lower the seat
automatically with minimal effort on the part of the operator.
WARNING! The power seat is intended for operation only while your scooter is stationary
and on a level surface. Its purpose is to aid you in reaching objects.
Strict adherence to the following safety rules is vital to your safety:
n Do not attempt to raise or lower the seat while in motion!
n Operate the power seat only on level ground.
n Do not operate your scooter with the power seat elevated.
n It is recommended that the scooter be driven only with the seat in the lowest
position.
Raising and lowering the power seat when traveling or when on an incline could cause the
scooter to tip over, resulting in serious injury and/or scooter damage. Keep the power seat
in its lowest position when traveling or when on an incline.
NOTE: Use of the power seat option will drain the charge on the batteries.
Operating your power seat:
1. Ensure your scooter is level and stationary.
2. Toggle on the power seat switch that is located on the tiller console.
3. To raise the power seat, place your hands on the handgrips and use your thumb to push the right side of the
lever.
4. Release the lever when you have attained your desired height.
5. To lower the power seat, place your hands on the handgrips and use your thumb to push the left side of the
lever.
6. Release the lever when you have attained your desired height.
7. Ensure your seat is in the lowest position and toggle off the power seat switch before you attempt to drive your
scooter again.
Ultimate 3-4/Rev A/July03
31
Page 32
VIII. DISASSEMBLY AND ASSEMBLY
DISASSEMBLY
You can disassemble the scooter into seven pieces: the seat, the front section, the rear section, the rear shroud, the
basket, and the batteries. See figure 13. Place the scooter in an area where you have sufficient clearance to move
the parts around. You need about 1.5 to 2 meters in all directions. You may need assistance to lift some of the
scooter components. See III. Specifications for individual component weights.
WARNING! Lifting weight beyond your physical capability may result in personal injury.
Ask for assistance when necessar y while disassembling or assembling your scooter.
FRONT SECTION
SEAT
REAR SECTION
BATTERIES
REAR SHROUD
BASKET
Figure 13. The Ultimate 3-4 Disassembled
No tools are required to disassemble or assemble your scooter. Always disassemble or assemble your scooter on
a level, dry surface with sufficient room for you to work and move around your scooter. Keep in mind that the
disassembled sections of the scooter take up more floor space than the assembled scooter.
1. Place the manual freewheel lever in the drive (down) position.
2. Coil the charger power lead and store it for future use.
3. Push forward on the seat lock lever to unlock the seat; lift the seat up and off of the scooter.
4. Gently lift the rear shroud off of the scooter.
5. Disconnect the battery strap.
6. Unplug both black and white 2-pin battery harnesses. See figure 14.
7. Unplug the front-to-rear harness. See figure 14A.
WARNING! Failure to unplug both battery harnesses and the front-to-rear harness prior to
separating the front and rear sections could result in permanent damage to the scooter.
Figure 14. Battery Harnesses
32 Ultimate 3-4/Rev A/July03
Figure 14A. Front-To-Rear Harness
Page 33
VIII. DISASSEMBLY AND ASSEMBLY
Toggle Latch Release
1. Push in the toggle latch release button while pulling back the toggle latch. See figure 15.
2. Position the toggle latch buckle over the top of the toggle latch. See figure 16.
3. Lower the tiller to the scooter floorboard.
TOGGLE
TOGGLE
LATCH
TOGGLE
LATCH
RELEASE
BUTTON
LATCH
BUCKLE
Figure 15. T oggle Latch (Latched)
Figure 16. T oggle Latch (Unlatched)
Frame Separation
1. Push back on the seat post to pivot the scooters rear section rearwards until the rear section is standing
vertically on its rear bumper. See figure 17.
2. Lift the front section up until the lower pegs are no longer in the slots. See figure 18.
3. Carefully move the front section away from the rear section.
Figure 17. Frame Positioning Figure 18. Separating The Frame Sections
Ultimate 3-4/Rev A/July03
33
Page 34
VIII. DISASSEMBLY AND ASSEMBLY
ASSEMBLY
1. Position the front and rear sections of your scooter as
shown in figure 19.
2. Align the lower slots of the front section with the cor-
responding pegs on the front of the rear section.
WARNING! Position the front-to-rear
harness cable so it wont become
pinched between the frame halves
when pivoting the rear section forward.
See figure 20.
3. Holding the seat post, slowly pivot the rear section for-
ward until the curved locking brackets are fully connected onto the top rear pegs. See figures 19 and 20.
4. Raise the tiller.
5. Secure the toggle latch. See figure 15.
n Lower the toggle latch buckle.
n Push back on the toggle latch so it locks into place.
6. Connect the front-to-rear harness and both 2-pin,
black and white battery harnesses.
7. Replace the shroud.
8. Replace the seat, and lock it into place.
PEG
CURVED LOCKING BRACKETS
Figure 19. Frame Sections
FRONT-TO-REAR HARNESS CABLE
Figure 20. Frame Lockup
34 Ultimate 3-4/Rev A/July03
Page 35
IX. OPTIONAL ACCESSORIES
OPTIONAL ACCESSORIES
For information concerning these and other optional accessories, contact your authorised Pride Provider.
•Single Cane/Crutch Holder
• Walker Holder• Double Cane/Crutch Holder
• Rear Basket• Oxygen T ank Holder• Forearm Crutch Holder
• Safety Flag • Double Crutch Holder
• Cup Holder
Ultimate 3-4/Rev A/July03
• Quad Cane Holder
35
Page 36
X. BASIC TROUBLESHOOTING
Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that
may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because
the batteries are not fully charged or because the batteries are worn down and can no longer hold a charge.
DIAGNOSTIC FLASH CODES
The diagnostic flash codes for your scooter are designed to help you perform basic troubleshooting quickly and
easily. A diagnostic flash code will flash from the status LED in the event one of the conditions listed below develops.
NOTE: Your Scooter will not run unless the flash code condition is resolved and the
scooter has been turned off then turned back on.
FLASH CODE CONDITION SOLUTION
n n n n n
n n
n n n n
n n n n n
n n n n n n
Batte r ies are too low to op e r a te the
scooter or the charger is operating.
Controller is hot; the scoote r seem s to
be losing power.
Wigwag fault; your throttle control
levers are not responding .
The manual freewheel lever is in the
(up) freewheel position.
Scooter is operating with the charger
attached.
Charge batteries or unplug the charger power
cord from th e electrical outlet.
Shut down your scooter for a minimum of
several minutes to allow the controller to
cool.
Call your authorized Pride Provider for
assistance.
Turn the scooter ke y to the off position, then
push the freewheel lever to the (down) drive
position, restart your scoot er.
Unplug the ch arg er co r d f ro m the charger
power cord receptacle.
What if all the systems on my scooter seem to be dead?
n Make certain that the key is in the on position.
n Check that the batteries are fully charged. See V. Batteries and Charging.
n Push in the main circuit breaker reset button. See IV. Your Scooter.
n Make certain that both battery harnesses are firmly connected to their receptacles on the rear section. See
VIII. Disassembly and Assembly.
n Make sure that the front-to-rear harness is firmly connected. See VIII. Disassembly and Assembly.
n Check the 3-amp fuse located on the lower portion of the tiller console. See XI. Care and Maintenance for
fuse replacement.
n Be sure the Power Down Timer feature hasnt been activated. See VI. Operation.
What if my scooter does not move when I press the throttle control levers?
n When the manual freewheel lever is pulled up, the brakes are disengaged and all power to the motor/transaxle
assembly is cut.
n Push down on the manual freewheel lever, turn the scooter off, and then turn the scooter on to return to normal
scooter operation.
36 Ultimate 3-4/Rev A/July03
Page 37
X. BASIC TROUBLESHOOTING
What if the main circuit breaker repeatedly trips?
n Charge the scooters batteries more frequently. See V. Batteries and Charging.
n If the problem continues, have both of your scooters batteries load tested by your authorised Pride Provider.
n You may also perform the load test yourself. Battery load testers are available at most automotive parts stores.
n Follow the directions supplied with the load tester.
n See V. Batteries and Charging or III. Specifications for information about your scooters battery type.
What if the battery condition meter dips way down and the motor surges or hesitates when I press my
scooters throttle control lever?
n Fully charge your scooters batteries. See V. Batteries and Charging.
n Have your authorised Pride Provider load test each battery.
n Or, see the previous troubleshooting question for load testing the batteries yourself.
If you experience any problems with your scooter that you are not able to solve, immediately contact your authorised
Pride Provider for information, maintenance, and service.
Ultimate 3-4/Rev A/July03
37
Page 38
XI. CARE AND MAINTENANCE
Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your ability to
perform the maintenance listed below, you may schedule inspection and maintenance at your authorised Pride
Provider. The following areas require periodic inspection and/or care and maintenance.
TYRE PRESSURE
If equipped with pneumatic tyres, always maintain a proper 2-2.4 bar (30-35 psi) tyre pressure.
WARNING! It is important that 2-2.4 bar (30-35 psi) tyre pressure be maintained in pneumatic
tyres at all times. Do not underinflate or overinflate your tyres. Low pressure may result in
loss of control, and overinflated tyres may burst. Failure to maintain 2-2.4 bar (30-35 psi)
tyre pressure in pneumatic tyres at all times may result in tyre and/or wheel failure, causing
serious personal injury and/or damage to your scooter.
Regularly inspect your scooters tyres for signs of wear.
EXTERIOR SURFACES
Bumpers, tyres, trim, and the tiller boot can benefit from an occasional application of a rubber or vinyl conditioner.
WARNING! Do not use a rubber or vinyl conditioner on the scooters vinyl seat, floorboard,
or tyre tread. They will become dangerously slippery and result in personal injur y and/or
damage to your scooter.
BATTERY TERMINAL CONNECTIONS
n Make certain that the terminal connections remain tight and uncorroded.
n The batteries must sit flat in the battery wells.
n The battery terminals should face the rear of the scooter.
WIRING HARNESSES
n Regularly check all wiring connections.
n Regularly check all wiring insulation, including the charger power lead, for wear or damage.
n Have your authorised Pride Provider repair or replace any damaged connector, connection, or insulation that
you find before using your scooter again.
ABS PLASTIC SHROUDS
n The front tiller shroud, front shroud, and the rear shroud are formed from durable ABS plastic and are coated
with an advanced formula urethane paint.
n A light application of car wax will help the shrouds retain their high gloss.
AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY
These items are all prelubricated, sealed, and require no subsequent lubrication.
MOTOR BRUSHES
The motor brushes are housed inside of the motor transaxle/assembly. They should be inspected periodically for
wear by your authorised Pride Provider.
38 Ultimate 3-4/Rev A/July03
Page 39
XI. CARE AND MAINTENANCE
CONSOLE, CHARGER, AND REAR ELECTRONICS
n Allow these areas to dry thoroughly if they have been exposed to moisture before operating your scooter again.
FUSE REPLACEMENT
In the event a fuse should cease to work:
1. Remove the fuse by pulling it out of its slot.
2. Examine the fuse to be sure it is blown. See figures 21 and 21A.
3. Insert a new fuse of the proper rating.
WARNING! The replacement fuse must exactly match the rating of the new fuse. Failure
to use properly rated fuses may cause damage to the electrical system and may result in
personal injury.
Figure 21. Working Fuse Figure 21A. Blown Fuse (Replace)
REAR LIGHTS
Light bulbs for the rear running lights and turn indicators are easily replaceable.
NOTE: Replacement light bulbs can be purchased from your authorised Pride Provider.
Use only 24-volt light bulbs.
1. Remove the light cover.
2. Gently remove the bulb by pulling it straight out.
3. Insert a new 24-volt, 5-watt bulb.
4. Replace the light cover.
STORING YOUR SCOOTER
If you plan on not using your scooter for an extended period of time, it is best to:
n Fully charge its batteries prior to storage.
n Disconnect the batteries from the scooter.
n Store your scooter in a warm, dry environment.
n Avoid storing your scooter where it will be exposed to temperature extremes.
WARNING! Always protect batteries from freezing temperatures and never charge a frozen
battery. This damages the battery and can cause personal injury.
For prolonged storage, you may wish to place several boards under the frame of your scooter to raise it off of the
ground. This takes the weight off the tyres and reduces the possibility of flat spots developing on the areas of the
tyres contacting the ground.
Ultimate 3-4/Rev A/July03
39
Page 40
XII. WARRANTY
TWO-YEAR LIMITED WARRANTY
Structural frame components, including: platform, fork, seat post, and frame welds.
Drive train, including: differential, motor, and brake.
ONE-YEAR LIMITED WARRANTY
All other parts, including controllers and battery chargers, will be free from defects in material and workmanship
for a period of one year from delivery.
NOT COVERED UNDER WARRANTY
The warranty does not extend to any defect arising from fair wear and tear or willful damage, negligence, abnormal
working conditions, failure to follow our instructions (whether oral or in writing), use not in accordance with the
owners manual, misuse or alteration or repair of the scooter without our approval.
The warranty does not cover tyres, belts, bulbs, upholstery, plastic shrouds, motor brushes, fuses, and batteries.
This does not affect your statutory rights relating to quality and condition of these items.
Any defect covered by the warranty may be repaired in satisfaction of claims under the warranty.
A charge for call out and labor for in-home repair may be made under the warranty save where the defect falls
under the customers statutory rights relating to quality and condition of the scooter.
The warranty in respect of the controller and battery charger shall lapse if any attempt is made to open or dismantle
such items by unauthorised personnel.
BATTERIES
Gradual deterioration in performance due to being left in a discharged state, left in cold conditions for long periods
of time, or worn out through heavy use is not covered.
Batteries will be covered under the warranty only where they have been charged and maintained fully in accordance with the owners manual.
SERVICE CHECKS AND WARRANTY SERVICE
Warranty service can be arranged by Pride. Please contact Pride for information on the current cost affecting
service visits.
For servicing and warranty queries please contact your authorised Pride Provider.
40 Ultimate 3-4/Rev A/July03
Loading...