SilverStar
Exterior LIft
™
www.silverst arlifts.com www .pridemobility .com
SAFETY GUIDELINES
WARNING! An authorized Pride Provider or qualified technician must perform the initial
setup of this lift and must perform all of the instructions in this manual.
The symbols below are used throughout this owner's manual and on the product to identify warnings and important
information. It is very important for you to read them and understand them completely .
WARNING! Indicates a potentially hazardous condition/situation. Failure to follow
designated procedures can cause either personal injury, component damage, or
malfunction. On the product, this icon is represented as a black symbol on a yellow triangle
with a black border.
MANDATORY! These actions should be performed as specified. Failure to perform
mandatory actions can cause personal injury and/or equipment damage. On the product,
this icon is represented as a white symbol on a blue dot with a white border .
PROHIBITED! These actions are prohibited. These actions should not be performed at any
time or in any circumstances. Performing a prohibited action can cause per sonal injury
and/or equipment damage. On the product, this icon is represented as a black symbol with
a red circle and red slash.
Please fill out the following information for quick reference:
Pride Provider:_____________________________________________________________________
Address:__________________________________________________________________________
Phone Number: ___________________
Purchase Date:____________________ Serial Number:_________________________________
NOTE: This owner’s manual is compiled from the latest specifications and product information available at the time of publication. We reserve the right to make changes as they become necessary. Any
changes to our products may cause slight variations between the illustrations and explanations in this
manual and the product you have purchased. The latest/current version of this manual is available on
our website.
Copyright © 2007
Pride Mobility Products Corp.
INFMANU3279/Rev C/June 2007
088 609 661
CONTENTS
I. INTRODUCTION......................................................................................................................... 4
II. SAFETY ......................................................................................................................................... 6
III. INSTALLATION ........................................................................................................................ 10
IV. OPERATION............................................................................................................................... 14
V . BATTER Y CHARGING............................................................................................................ 16
VI. CARE AND MAINTENANCE................................................................................................ 17
VII. TROUBLESHOOTING............................................................................................................ 19
VIII.SPECIFICATIONS ................................................................................................................... 20
IX. WARRANTY................................................................................................................................21
Exterior Lift System www.pridemobility.com 3
I. INTRODUCTION
I. INTRODUCTION
Welcome to Pride Mobility Products Corporation (Pride). Congratulations on the purchase of your new Exterior
Lift System. The Exterior Lift System design combines the most advanced state-of-the-art components with modern,
attractive styling. We are certain that the design features and trouble-free operation will add convenience to your
daily living and ensure complete satisfaction.
At Pride, your safety is important to us. Please read and follow all instructions in this manual before
operating your lift system for the first time. These instructions were produced for your benefit. Your
understanding of these instructions is essential for the safe operation of your new lift system.
Pride is not liable for damage to property or personal injury arising out of the unsafe use of an Exterior Lift
System. Pride is also not liable for any property damage or personal injury arising out of the failure of any person
and/or user to follow the instructions and recommendations set forth in this manual or any other instructions or
recommendations contained in other lift system related literature issued by Pride or contained on the Exterior
Lift System itself.
INTERNET AND PRIVATE PURCHASES
If you purchased your product over the internet or from a previous owner and you have any questions about
the safe use and/or maintenance of the product, please visit Silver Star’s web site www.silverstarlifts.com or
contact your authorized Pride Provider.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter, or modify this product or
remove or render inoperable or unsafe any guards, shields, or other safety features of this product; fail,
refuse, or neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the safe use
of this product.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear
about the safety and reliability of your new lift system, and about the service you received from your
authorized Pride Provider.
Please notify us of any change of address, so we can keep you apprised of important information about
safety, new products, and new options that can increase your ability to use and enjoy your new lift system.
Please feel free to contact us at the address below:
PRIDE OWNERS CLUB
As an owner of a Pride product, you are encouraged to enroll in the Pride Owners Club. Complete and
return your enclosed product registration card or visit Pride’s web site at www.pridemobility.com.
From our home page, select “Owners Club” to enter a page dedicated to current and potential Pride product
owners. You will gain access to interviews, stories, recreation ideas, daily living tips, product and funding
information, and interactive message boards. These message boards invite you to communicate with other
Pride customers as well as Pride representatives who are available to assist you with any questions or
concerns you may have.
Pride Mobility Products Corporation
Attn.: Customer Care Department
182 Susquehanna A ve.
Exeter, PA 18643-2694
customercare@pridemobility.com
800.424.8205
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact
us and we will be glad to send you a new one immediately.
Exterior Lift System www.pridemobility.com 54 www.pridemobility .com Exterior Lift System
II. SAFETY
PRODUCT SAFETY SYMBOLS
The symbols below are used on the lift system to identify warnings, mandatory actions, and prohibited
actions. It is very important for you to read and understand them completely.
II. SAFETY
Contains lead.
Do not sit on Power Chair or
Scooter while activating lift
or during transport.
DWR1235L111 REV A
Crush Hazard—Pinch/crush points created during assembly and operation.
Keep hands clear.
Do not sit on mobility device while activating lift or during transport.
Crush Hazard—Moving lift can crush. Keep feet clear during operation.
Read and follow the information in the owner’s manual.
Maximum lifting capacity .
Do not use as a step.
Lift system intended for use with unoccupied mobility device. Do not use
product to lift people.
Removal of grounding prong can create electrical hazard. If necessary,
properly install an approved 3-pronged adapter to an electrical outlet having
2-pronged plug access.
Wear safety goggles.
Explosive conditions exist!
Do not allow unsupervised children to play near the lift system while the batteries
are charging.
Avoid exposure to rain, snow, ice, salt, or standing water whenever possible.
Maintain and store in a clean and dry condition.
Disposal and recycling-Contact your authorized Pride Provider for information on proper
disposal of your Pride product and its packaging.
Disposal and recycling-Contact your authorized Pride Provider for inf ormation on proper
disposal of your Pride product and its packaging.
Do not connect an extension cord to the charger cord.
Exterior Lift System www.pridemobility.com 76 www.pridemobility .com Exterior Lift System
II. SAFETY
II. SAFETY
LIFTING CAPABILITIES
The Exterior Lift System is an electromechanical device designed to lift various types of mobility devices for the
purpose of vehicle transport. The Exterior Lift System is designed for a maximum Class 2 hitch allowance of
190 lbs. (86 kg) and a maximum Class 3 hitch allowance of 325 lbs. (147 kg). Under no circumstances should
the Exterior Lift System be made to exceed this weight limit. Subjecting the lift system to the strain of hoisting
more than it is designed to lift may cause it to fail, resulting in damage to the mobility device and/or the lift
operator. Refer to the mobility device owner’s manual for information on the overall weight of the mobility
device before lifting.
WARNING! Adding accessories, oversize batteries, or a different seat will increase the
weight of your mobility device. Verify with your authorized Pride Provider that the total
weight of your mobility device, including additions, does not exceed the maximum hitch
allowance.
INSTALLATION
The Exterior Lift System is designed to be mounted to a vehicle hitch system. Before lift installation, ensure that the
hitch shows no signs of rust or wear and that the front and rear vehicle suspension is acceptable. If any vehicle
alterations are necessary, make sure that you fully understand the instructions for drilling or cutting before making
any alterations.
WARNING! Before drilling or cutting into the vehicle, make absolutely certain through
visual inspection that there are no obstructions in the path of the drill bit, such as the fuel
tank, exhaust pipes, or electrical wires.
LIFTING NON-PRIDE PRODUCTS
The Exterior Lift System is an extremely versatile device, which users may employ to lift items other than Pride
products. Pride has no control over such use, nor can Pride anticipate every possible use to which a lift system may
be put. Lifting non-Pride products with the Exterior Lift System is done at the operator’s own risk, and Pride
accepts no liability for damage or injury resulting from such use.
PRELIFT INSPECTION
Before operating the Exterior Lift System, inspect your surroundings to ensure that the lift system has a clear path
of operation. Remove any possible obstructions before operating the lift and do not allow children to operate or
play near the lift.
OPERAT OR POSITIONING
The operator of the lift should stand a safe distance from the unit being lifted/lowered to ensure that his/her feet are
never positioned under the raised lift platform. The operator should also keep his/her hands clear of the lift system
to avoid the potential for injury.
HITCH CLASS INFORMA TION
Hitches come in a variety of sizes and are designated by class. The classes range from Class I to Class IV . The
heavier the load, the larger class of hitch having a greater tongue weight needed. T ongue weight is the amount
of weight (downward force) the load puts on the hitch. See figure 1.
The combined weight of your lift and mobility vehicle gives you the minimum tongue weight for your application.
Exceeding the tongue weight of a hitch creates an unsafe driving situation and can damage the hitch and/or the
vehicle. See figures 2 and 3.
WARNING! Adding accessories,
oversize batteries, or a different
seat will increase the weight of
your mobility vehicle. Verify with
your authorized Pride Provider that
the total weight of your mobility
device, including additions, does
not exceed the maximum weight
allowance.
WARNING! Never exceed the
maximum lifting capacity of a lift
regardless of the class of hitch being
used. Doing so may cause lift and/or
vehicle damage.
Figure 1. T ongue Weight Pressure P oint
Hitch Classes
! A Class I hitch has a maximum tongue weight of
200 lbs. (90.75 kg).
Figure 2. Unsafe Driving Situation
! A Class II hitch has a maximum tongue weight of
350 lbs. (158.75 kg).
! A Class III hitch has a maximum tongue weight
of 500 lbs. (225.75 kg).
! A Class IV hitch has a maximum tongue weight of
1200 lbs. (544.30 kg).
WARNING! Before installing the
(exterior) lift and applicable hitch
system, check your vehicle owner’s
manual for its hitch maximum
tongue weight capacity. Do not
exceed the maximum tongue weight
capacity of your vehicle.
Figure 3. Vehicle Damage
TRANSPORT VEHICLE POSITIONING
Be sure your vehicle is parked on flat, level ground before attempting to load, lift, or remove a mobility device with
the Exterior Lift System. Make sure the vehicle emergency park brake is engaged before loading or unloading a
mobility device.
Exterior Lift System www.pridemobility.com 98 www.pridemobility .com Exterior Lift System
III. INSTALLATION
III. INSTALLATION
EXTERIOR LIFT SYSTEM INSTALLATION
The Exterior Lift System is designed to be easily installed into any vehicle equipped with a Class 2 or Class 3 hitch receiver.
The hitch receiver should be installed no higher than 21 in. (53 cm) from the bottom of the hitch tube to the ground.
NOTE: Once installed, the lift system may obstruct the view of the vehicle license plate. Research the
local laws for license plate obstruction in your area and install the license plate kit. Contact your authorized Pride Provider for more information.
WARNING! Prevent product and/or vehicle damage! The Exterior Lift should be installed
by an authorized service technician only.
Follow these steps to install the Lock-Down-Arm:
1. Lay the lift system flat on the floor.
NOTE: If your lift system is equipped with a permanent threaded stud, removal of the pivot tube and
pivot bolt is not necessary for lock-down arm installation. See figure 4.
2. Apply power to the lift until there is enough clearance to remove the pivot bolt. See figure 4.
NOTE: If the pivot bolt does not remove easily, apply power to the lift and make a slight adjustment to
the angle of the pivot tube. Repeat as necessary.
3. Remove the pivot bolt. Keep hardware for reassembly.
4. Remove the pivot tube. See figure 4.
5. Insert the supplied screw through the countersunk hole of the u-bracket (from the inside out).
6. Position the lock-down arm onto the screw and insert the pivot bolt through the u-bracket and lock-down
arm. The pivot bolt is used for alignment purposes at this time.
7. Secure the nut to the securement screw and install the cap. Remove the pivot bolt.
8. Position the pivot tube onto the u-bracket and reinsert the pivot bolt through the u-bracket, pivot tube, and lock-down arm.
9. Install the nut back onto the pivot bolt and install the cap. Do not overtighten the nut. Ensure the pivot tube
pivots freely without binding.
THREADED
STUD
LIFT ARM SECUREMENT BOLT
Figure 4. Lock Down Arm Installation
PIVOT BOLT
CAP
NUT
CAP
NUT
PIVOT TUBE
U-BRACKET
LOCK DOWN ARM
Follow these steps to install the Exterior Lift System:
1. Remove the preassembled mounting hardware from the
LIFT FRAME
hitch tube.
2. Mount the hitch tube to the lift frame using the previously
removed mounting hardware. See figure 5.
3. Slide the hitch tube into the vehicle hitch receiver, aligning
HITCH TUBE
the mounting hole closest to the lift with the mounting hole
in the hitch receiver. See figure 6.
WARNING! Lift system components are
heavy. Ask for assistance if necessar y
when attaching the lift frame to the hitch
receiver, and use proper lifting
techniques.
WARNING! Avoid pinch points! Do not hold
the lift frame by the pivot points when
mounting the lift frame to the hitch
receiver.
Figure 5. Hitch Tube Assembly
MOUNTING HARDWARE
4. Secure the hitch tube with the supplied bolt and nut,
inserting the bolt from the passenger’s side through
to the driver’ s side of the hitch. See figure 6.
WARNING! Threading the bolt from the
wrong side or allowing the bolt to turn
while tightening the nut will dislodge the
threaded insert in the hitch tube.
WARNING! Do not attach a Class 2 hitch
tube to a Class 3 hitch receiver.
NOTE: Make sure the hitch bolt is tightened firmly
before securing the nut to the hitch assembly to minimize the chance that the lift will tilt during trans-
HITCH RECEIVER
port.
NOTE: Make sure the hitch tube and lift platform are
Figure 6. Lift Frame V ehicle Mounting
parallel to the ground before operating the lift system.
An angled hitch tube may cause unreliable lift operation and/or damage to the lift system.
5. Route the lift system wiring harness through the vehicle. Refer to “Wiring Harness Installation.”
WARNING! Route the wiring harness through the vehicle rather than under the vehicle to
avoid coming in contact with sharp edges, extreme temperatures, moving parts, and
roadway debris including road salt and other highly corrosive materials. Power shorts may
occur if wires come in contact with hot exhaust parts or sharp edges.
WARNING! Never attach the wiring harness to a secondary power source. Do not attempt
to use trailer wiring to power the lift system. The wiring harness must be connected directly
to the vehicle battery.
Exterior Lift System www.pridemobility.com 1110 www.pridemobility .com Exterior Lift System
III. INSTALLATION
III. INSTALLATION
NOTE: If your lift is equipped with an onboard battery, refer to “Onboard Battery Installation.”
6. Install the lift platform kit. Refer to the instructions supplied with the kit.
Wiring Harness Installation
The wiring harness is approximately 25 ft. (7.62 meters) long and will accommodate most vehicles.
NOTE: You may wish to perform a practice run before installing the wiring harness. Route a piece of
light rope (equivalent to the gage of the wiring harness) along the anticipated path observing contact
points, potential rubbing/chafing points, and any sharp edges. Remove sharp edges with a fine grade
file, then treat the steel with a rust inhibitor or metal sealant.
Follow these steps to route the Exterior Lift System wiring harness:
1. Route the lift system wiring harness (starting at the lift) through the interior of the vehicle until you reach the
vehicle battery. See figure 7. Y ou will typically find pass through points at the rear lighting assemblies, which will
enable you to route the cable through the trunk and under the back seat.
2. Conceal the harness behind or under the interior panels of the vehicle (there should be existing holes). Be
certain that the harness is protected with a rubber grommet when passing it through the metal panels and into
the engine compartment.
3. Inside the engine compartment, secure the harness to the firewall and the inner fender with plastic wire ties. Use
care not to cause abrasions to the wiring harness. It is important to secure the wiring harness at various points
along its run of the vehicle.
WARNING! Do not cut or shorten the wiring harness. If the harness is too long, coil the
excess wire and secure it with plastic wire ties.
4. Connect the red wire to the positive (+) terminal and the black (grounding) wire to the negative (-)
terminal of the vehicle battery.
WARNING! Before operating the lift, inspect the wiring harness for proper r outing and
grounding. Improper routing can cause damage to the harness, and improper grounding
can cause damage to the electrical system.
Onboard Battery Installation
The optional onboard battery is designed for easy installation as it does not require any wires to be routed through
or under the vehicle.
Follow these steps to install the onboard battery:
1. Align the mounting holes in the battery case bracket
with those in the accessory bracket located under the
key switch tube. See figure 8.
2. Secure the battery case to the accessory bracket with
the supplied hardware. See figure 8.
3. Insert the onboard battery into the battery case, making
sure that the connector on the bottom of the battery
aligns and fully connects with the mating connector
inside the battery case.
4. Plug the battery cord on the bottom of the battery
case into the mating connector running from the motor. See figure 8.
ACCESSORY BRACKET
BATTERY CASE
BATTERY CASE
BRACKET
Figure 8. Onboard Battery Installation
WIRING HARNESS
GROUNDING WIRE
VEHICLE BATTERY
Figure 7. Wiring Harness Installation
LIFT FRAME
LIFT WIRING CONNECTION
Exterior Lift System www.pridemobility.com 1312 www.pridemobility .com Exterior Lift System
IV. OPERATION
IV. OPERATION
EXTERIOR LIFT SYSTEM OPERA TION
WARNING! The Exterior Lift System is intended for the transport of mobility devices only.
The mobility device must be unoccupied before operating the lift.
WARNING! Do not exceed the load limits of your vehicle or hitch system as specified by
the vehicle manufacturer.
WARNING! Use extreme caution when driving with the lift installed on your vehicle. Be
aware that the lift extends away from the back of the vehicle and extra clearance is
needed when backing up, turning, par king, or driving thr ough driveway entrances/exits.
Drive slowly when negotiating pot holes, road bumps, and railroad tracks.
Follow these steps to operate the Exterior Lift System:
1. Insert the key into the key switch.
2. Turn and hold the key clockwise to lower the lift platform. See figure 9. Release the key as soon as the lift
platform touches the ground.
3. Set the speed control of the mobility device to the slowest setting and carefully drive your mobility device onto
the lift platform, being sure to center the mobility device
on the platform to the best of your ability.
NOTE: You may wish to load the mobility device while
standing next to it using the manual freewheel feature.
Refer to the mobility device owner’s manual for more
information on manual freewheel mode.
4. Shut down the power to the mobility device, remove the
key if applicable, and make sure the unit is in drive mode
(drive motors engaged). Refer to the mobility device
owner’s manual for more information on drive mode.
WARNING! Never leave a mobility device
in manual freewheel mode during lift
system transport, as the mobility device
could roll
5. Secure the mobility device to the platform using either the
retractable tie-down straps (see figure 10) for power
chairs or the automatic lock-down arm for scooters.
WARNING! Never attempt to secure the
tie-down straps over the seatback or
armrests of a mobility device.
Figure 9. Key Switch Operation
RELEASE
Figure 10. Retractable Tie-Down Straps
WARNING! For lift systems equipped with the automatic lock-down arm, do not attempt to
adjust the pressure of the arm. This feature has been configured by your authorized Pride
Provider to meet your needs and requires no further adjustment.
WARNING! If your scooter is equipped with pneumatic drive tires, make sure the tires are
inflated to the recommended pressure labeled on the tire sidewall. This will ensure that
the scooter is at the correct deck height for proper lock-down arm positioning.
NOTE: Inspect the tie-down straps before each use to ensure there are no signs of fraying or wear.
Ensure that the mobility device is secured properly before transport. Pride is not liable for damage or
loss resulting from improper securing of a mobility device.
6. Turn and hold the key counterclockwise to raise the lift. See figure 9. Continue to raise the lift until the motor
stops, then release the key.
NOTE: As the lift platform rises, the automatic lock-down arm activates to secure the scooter to the lift
platform. You may need to adjust the scooter tiller position to prevent interference with the smooth
operation of the automatic lock-down arm.
NOTE: The motor will stop automatically at the top of its stroke and will emit a clicking sound.
Release the key immediately upon hearing this sound, then turn the key counterclockwise one more
time for no more than 2 seconds to ensure the platform is in the fully raised position.
NOTE: Pay attention to the path of the lift platform during operation. Make sure the lift does not rub
against or interfere with the vehicle in any way. If you notice any contact between the lift platform and
the vehicle, stop lift operation immediately and contact your authorized Pride Provider for assistance.
Follow these steps to remove a mobility device from the Exterior Lift System:
1. Lower the lift platform to the ground.
2. Unfasten the tie-down straps or allow the lock-down arm to automatically return to the vertical position.
3. Unload the mobility device from the lift platform.
4. Raise the lift platform for storage, noting that it will automatically fold into a stowed position.
5. Remove the key from the lift system when it is not in use.
WARNING! Do not attempt to manually pull
the lift platform down from the stowed
position. Doing so will result in product
damage and will void the product
warranty.
MANUAL CRANK
MOTOR HOUSING
MANUAL EXTERIOR LIFT OPERA TION
The lift system is equipped with a manual crank that serves as
backup in the event of a power failure. Using the supplied
tool, rotate the manual crank (located on top of the motor
housing) clockwise or counterclockwise to move the platform up or down. See figure 11.
Figure 11. Manual Crank Operation
Exterior Lift System www.pridemobility.com 1514 www.pridemobility .com Exterior Lift System
V. BATTERY CHARGING
V. BATTERY CHARGING
BATTER Y CHARGING
Follow these steps to charge the onboard battery:
1. Remove the onboard battery from the battery case and
place it near a standard electrical outlet.
2. Plug the charger cord into the mating socket located on
the bottom of the battery case, then connect the charger
cord to a standard electrical outlet. See figure 12.
NOTE: It is recommended that you replace the battery
every 3–5 years. Store the battery in a moisture-free
environment when not in use.
MANDATORY! Read the battery charging
instructions in this manual and in the
manual supplied with the battery charger
before charging the battery .
PROHIBITED! Never use an extension
cord to plug in your charger cord. Plug
the charger cord directly into a properly
wired standard electrical outlet.
PROHIBITED! Removal of the grounding
prong can create an electrical hazard. If necessary, properly install an approved 3-pronged
adapter to an electrical outlet having 2-pronged plug access.
PROHIBITED! Do not allow unsupervised children to play near the battery or battery charger
while the battery is charging.
PROHIBITED! Do no expose the battery charger to rain or other sources of moisture unless
it has been tested for outdoor use. Refer to the manual supplied with the battery charger
for more information.
WARNING! Explosive gases may be generated while charging the battery. Keep the battery
and the battery charger away from sources of ignition such as flames or sparks and provide
adequate ventilation when charging the battery.
WARNING! Do not attempt to charge the battery and operate the lift system at the same
time.
WARNING! Do not attempt to wire the lift system directly to the vehicle battery if the lift
system is equipped with an onboard battery.
WARNING! You must recharge the lift system battery with the supplied battery charger.
Do not use an automotive-type battery charger.
WARNING! If the battery is exposed to adverse or extreme weather conditions, then it
must be allowed to adjust to the difference in environmental conditions before being
charged.
WARNING! Inspect the battery charger, wiring, and connectors for damage before each
use. Contact your authorized Pride Provider if damage is found.
WARNING! Do not attempt to open the battery charger case. If the battery charger does
not appear to be working correctly, contact your authorized Pride Provider.
Figure 12. Battery Charging
BATTERY REPLACEMENT
WARNING! Battery posts, terminals, and related accessories contain lead and
lead compounds. Wear goggles and wash hands after handling.
MANDAT OR Y! Use only AGM or Gel-Cell batteries.
WARNING! Corrosive chemicals contained in battery. Use only AGM or Gel-Cell batteries
to reduce the risk of leakage or explosive conditions.
WARNING! Contact with tools can cause electrical shock.
WARNING! Connect the battery harnesses in the proper manner. RED (+) cables must be
connected to positive (+) battery terminals/posts. BLACK (-) cables must be connected to
negative (-) battery terminals/posts. REPLACE cables immediately if damaged. Protective
caps must be installed over all battery terminals.
NOTE: If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag and call
your authorized Pride Provider for instructions on disposal. Your authorized Pride Provider will also
have the necessary information on battery recycling, which is our recommended course of action.
Follow these steps to replace the onboard bat-
BATTERY BOX
tery (figure 13):
1. Unfasten the battery securement strap located at
the bottom of the battery box.
2. Remove the hardware from the battery securement bracket and remove the bracket.
3. Remove the hardware from the battery connector.
4. Slide the battery out of the battery box to expose
the battery harness.
5. Disconnect the battery harnesses from the battery
terminals.
6. Connect the battery harnesses to the new battery.
7. Slide the new battery into the battery box.
8. Reinstall the hardware to secure the battery connector and tighten.
9. Reinstall the battery securement bracket and
tighten the hardware.
10. Refasten the battery securement strap.
If your lift system is exhibiting wear that you feel is
BATTERY SECUREMENT BRACKET
BATTERY SECUREMENT STRAP
Figure 13. Battery Replacement
BATTERY CONNECTOR
questionable in any way, contact your authorized Pride
Provider immediately. Do not attempt to repair , adjust, or modify the manufacturer settings and materials.
Exterior Lift System www.pridemobility.com 1716 www.pridemobility .com Exterior Lift System
VI. CARE AND MAINTENANCE
VII. TROUBLESHOOTING
CARE AND MAINTENANCE
Y our lift system requires a minimal amount of care and maintenance. If you do not feel confident in your ability to
perform the maintenance listed below, you may schedule inspection and maintenance at your authorized Pride
Provider. The following areas require periodic inspection and/or care and maintenance.
90-Day Maintenance Schedule
! Lower the platform to the ground, clean away any rem-
nants of old grease from the T-bar inner -telescoping tube,
and apply a new coat of all-weather lithium grease to the
inner-telescoping tube. See figure 14.
! Apply all-weather lithium grease to the pivot points of the
T-bar.
! Lubricate the key switch with an electrical-type lubricant
(not WD-40).
! Remove the vehicle battery connections and clean them
to ensure uninterrupted electronic connection.
! Torque the hitch bolt.
! Check the lift system for loose or damaged parts. Have
your authorized Pride Provider repair or replace any
problem parts before using the lift system.
General Cleaning Guidelines
The lift system can be hand washed along with the vehicle with soap and water. However, automatic drive-through
car washes should be avoided as they may interfere with and cause damage to the lift.
Wiring Harness
The wiring harness should be checked periodically for corrosion and/or decay. Contact your authorized Pride
Provider if the wiring harness needs to be replaced.
Lift Platform/Metal Components
! Check the lift platform for wear or damage. Contact your authorized Pride Provider for repair or replacement.
! The lift platform surface may become slippery if exposed to moisture (ice, snow, rain, mist/spray conditions,
etc.). Use caution when loading/unloading a mobility device in these conditions and wipe off any excess
moisture from the lift platform.
! Regularly inspect the metal lift components for scratches. Treat any problem areas with a rust inhibitor or metal
sealant.
Figure 14. Lift Frame Maintenance
T-BAR INNERTELESCOPING TUBE
TROUBLESHOOTING
Any electromechanical device occasionally requires some troubleshooting. However, most of the problems that
may arise can usually be solved with a bit of thought and common sense. Many of these problems occur because
the battery is not fully charged or because the battery is worn down and can no longer hold a charge.
What if the motor on my lift system will not operate?
! Make sure the onboard battery or vehicle battery is fully charged.
! Make sure all connections to the motor and battery are secure.
! Check the wiring harness for signs of wear or decay. Replace the harness if necessary .
What if the lift system operates slowly up or down?
! Make sure the onboard battery or vehicle battery is fully charged.
! Make sure all connections to the motor and battery are secure.
! Check the wiring harness for signs of wear or decay. Replace the harness if necessary .
What if the lift platform does not fold into the stowed position?
Check to make sure there are no obstructions in the T -bar pivot points.
What if the lift platform does not lower completely to the ground?
! Verify that the hitch receiver is at the proper height. The distance from the bottom of the hitch to the ground
should not exceed 21 in. (53 cm).
! Check to make sure that the area under the lift platform is free from obstructions.
What if the lift bottoms out when driving over bumps or driveway entrances?
V erify that the hitch receiver is at the proper height. The distance from the bottom of the hitch to the ground should
be 21 in. (53 cm).
If your lift system is exhibiting wear that you feel is questionable in any way, contact your authorized Pride Provider
immediately. Do not attempt to repair , adjust, or modify the manufacturer settings and materials.
Lift Removal
! Raise platform to stowed position.
! Disconnect power source.
! Lubricate hitch mount bolt with WD-40 prior to removal.
Exterior Lift System www.pridemobility.com 1918 www.pridemobility .com Exterior Lift System
VIII. SPECIFICATIONS
IX. WARRANTY
SPECIFICATIONS
Lift System Dimensions: Overall Height: 58 in. (147 cm)
Overall Width: 41–44 in. (104–112 cm) from hitch with platform down
20 in. (51 cm) from hitch with platform folded
Platform Width:28 in. (71 cm)
Maximum Lift Capacity: 190 lbs. (86 kg) with Class 2 hitch
325 lbs. (147 kg) with Class 3 or higher hitch
Maximum Mobility 27 in. (68.58 cm)
Device Width:
Maximum Hitch-to- 21 in. (53 cm)
Ground Clearance:
Motor: Fully sealed, 12-volt DC
Onboard Battery: 12-volt, 18 AH
Charger: 110-volt, off-board
THREE-YEAR TRANSFERABLE LIMITED WARRANTY
For three (3) years from the date of purchase, Pride Mobility Products will repair or replace at our option, free of
charge, any mechanical or electrical component found upon examination by an authorized representative of Pride
to be defective in material and/or workmanship.
This warranty does not extend to those items, which may require replacement due to normal wear and tear.
! Labor, service calls, shipping, and other charges incurred for repair of the product, unless specifically autho-
rized by Pride Mobility Products Corporation IN ADVANCE, are excluded.
Exclusions also include components with damage caused by:
! Contamination
! Abuse, misuse, accident, or negligence
! Battery fluid spillage or leakage
! Commercial use, or use other than normal
! Improper operation, maintenance, or storage
! Repairs and/or modifications made to any part without specific consent from Pride Mobility Products Corpo-
ration.
! Circumstances beyond the control of Pride
ONE-YEAR WARRANTY
The battery is covered by a separate one (1) year warranty provided by the battery manufacturer. The batteries
are not warranted by Pride Mobility Products Corporation.
SERVICE CHECKS AND WARRANTY SERVICE
An authorized Pride Mobility Products Provider must perform warranty service. Do not return faulty parts to Pride
Mobility Products without prior written authorization. All transportation costs and shipping damage incurred while
submitting parts for repair or replacement is the responsibility of the purchaser.
Failure to follow the instructions, warnings, and notes in the owner’s manual and those located on your Pride lift
product can result in personal injury or product damage and will void Pride’s product warranty .
There is no other express warranty.
IMPLIED WARRANTIES
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1)
year from the date of purchase and to the extent permitted by law. Any and all implied warranties are excluded.
This is the exclusive remedy. Liabilities for consequential damages under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of
limitation incidental or consequential damages. The above limitation or exclusion may not apply to you.
This warranty gives you specific rights, and you may also have other rights, which vary from state to state.
Please fill out and return the product registration card to Pride Mobility Products. This will aid Pride in providing
the best possible technical and customer service.
Exterior Lift System www.pridemobility.com 2120 www.pridemobility .com Exterior Lift System
*INFMANU3279*
Loading...