Owner ’s Manual
ATTENTION:
Please read the content
of your owners manual
before operating your
scooter.
The Ultimate In Style & Performance
®
Exeter, PA
St. Catharines, ON 1-800-800-8586
www.pridemobility.com
SAFETY GUIDELINES
The symbols below are used throughout this owner's manual and on the scooter to identify warnings and
important information. It is very important for you to read them and understand them completely .
WARNING! Indicates a potentially hazardous condition/situation that can cause personal
injury, equipment and/or property damage. (Black symbol on yellow triangle with black
border).
MANDATORY! These actions should be performed as specified. Failure to perform
mandatory actions can cause injury to personnel and/or damage to equipment (white
symbol on blue dot).
PROHIBITED! These actions are prohibited; do not perform at any time or in any situation.
Performing a prohibited action can cause personal injury and/or equipment damage (black
symbol with red circle and red slash).
Please fill out the following information for quick reference:
Pride Provider:____________________________________________________________________
Purchase Date:___________________________________________________________________
Address:__________________________________________________________________________
Phone Number:_____________________________________________________________________
Serial Number:____________________________________________________________________ __
NOTE: This owner’s manual is compiled from the latest specifications and product information
available at the time of publication. We reserve the right to make changes as they become necessary. Any changes to our products may cause slight variations between the illustrations and explanations in this manual and the product you have purchased.
Copyright © 2004
Pride Mobility Products Corp.
INFMANU2058/Rev D/November 2004
CONTENTS
I. INTRODUCTION ........................................................................................................................ 4
II. SAFETY ......................................................................................................................................... 5
III. EMI/RFI ........................................................................................................................................ 14
IV. SPECIFICATIONS ................................................................................................................... 16
V. YOUR SCOOTER ..................................................................................................................... 18
VI. BATTERIES AND CHARGING ........................................................................................... 23
VII. OPERATION ............................................................................................................................... 27
VIII.COMFORT ADJUSTMENTS................................................................................................ 29
IX. DISASSEMBLY AND ASSEMBLY..................................................................................... 32
X. BASIC TROUBLESHOOTING ............................................................................................. 35
XI. CARE AND MAINTENANCE ............................................................................................... 37
XII. WARRANTY ............................................................................................................................... 39
Maxima www.pridemobility.com
3
I. INTRODUCTION
SAFETY
WELCOME to Pride Mobility Products Corporation (Pride). The product you have purchased combines
state of the art components with safety, comfort and styling in mind. We are confident the design features
will provide you with the conveniences you expect during your daily activities. Understanding how to
safely operate and care for this product should bring you years of trouble free operations and service.
Read and follow all instructions, warnings, and notes in this manual and all other accompanying literature
before attempting to operate this product for the first time. In addition, your safety depends upon you, as
well as your provider, caretaker, or healthcare professional in using good judgement.
If there is any information in this manual which you do not understand, or if you require additional assistance for setup or operation, please contact your authorized Pride Provider. Failure to follow the instruc-
tions, warnings, and notes in this manual and those located on your Pride product can result in
personal injury or product damage and will void Prides product warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter or modify this product or
remove or render inoperable or unsafe any guards, shields, or other safety features of this product; fail,
refuse or neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the
safe use of this product.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear
about the safety and reliability of your new scooter, and about the service you received from your authorized Pride Provider. Please notify us of any change of address, so we can keep you apprised of important
information about safety, new products, and new options that can increase your ability to use and enjoy
your scooter. Please feel free to contact us at the address below:
Pride Mobility Products Corporation
Attn: Customer Care Department
182 Susquehanna Ave.
Exeter, PA 18643-2694
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us
and we will be glad to send you a new one immediately.
PRIDE OWNERS CLUB
As an owner of a Pride product, you are encouraged to enroll in the Pride Owners Club. Complete and
return your enclosed product registration card or visit Pride's web site at www.pridemobility.com.
From our home page, select Owners Club to enter a page dedicated to current and potential Pride product
owners. You will gain access to interviews, stories, recreation ideas, daily living tips, product and funding
information, and interactive message boards. These message boards invite you to communicate with other
Pride customers as well as Pride representatives who are available to assist you with any questions or
concerns.
4
www.pridemobility.com Maxima
II. SAFETY
GENERAL
MANDATORY! Do not operate your new scooter for the first time without completely reading
and understanding this owners manual.
Your scooter is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an
extensive variety of products to best fit the individual needs of the scooter user. Please be aware that the
final selection and purchasing decision regarding the type of scooter to be used is the responsibility of the
scooter user who is capable of making such a decision and his/her healthcare professional (i.e., medical
doctor, physical therapist, etc.).
There are certain situations, including some medical conditions, where the scooter user will need to practice operating the scooter in the presence of a trained attendant. A trained attendant can be defined as a
family member or care professional specially trained in assisting a scooter user in various daily living
activities.
As you begin using your scooter during daily activities, you will probably encounter situations in which
you will need some practice. Simply take your time and you will soon be in full and confident control as
you maneuver through doorways, on and off of elevators, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help the user become accustomed to operating the scooter safely.
MODIFICATIONS
Pride has designed and engineered your scooter to provide maximum mobility and utility. However, under
no circumstances should you modify, add, remove, or disable any feature, part, or function of your scooter.
WARNING! Do not modify your scooter in any way not authorized by Pride. Unauthorized
modifications may result in personal injury and/or damage to your scooter.
REMOVABLE PARTS
WARNING! Do not attempt to lift or move your scooter by any of its removable parts.
Personal injury and damage to the scooter may result.
ELECTROMAGNETIC FIELDS
Your scooters road performance features may be influenced by electromagnetic fields caused by cellular
telephones or other radiating devices, such as hand-held radios, radio and television stations, wireless
computer links, microwave sources, and paging transmitters.
Maxima www.pridemobility.com
5
II. SAFETY
PRE-RIDE SAFETY CHECK
Get to know the feel of your scooter and its capabilities. Pride recommends that you perform a safety check
before each use to make sure your scooter operates smoothly and safely. For details on how to perform
these necessary inspections, see XI. Care and Maintenance.
Perform the following inspections prior to using your scooter:
n Check for proper tire inflation (if equipped with pneumatic tires).
n Check all electrical connections. Make sure they are tight and not corroded.
n Check all harness connections. Make sure they are secured properly.
n Check the brakes.
n Check battery charge.
If you discover a problem, contact your authorized Pride Provider for assistance.
TIRE INFLATION
If your scooter is equipped with pneumatic tires, you should check or have the air pressure checked at least
once a week. Proper inflation pressures will prolong the life of your tires and help ensure the smooth
operation of your scooter.
WARNING! It is critically important that 30-35 psi tire pressure be maintained in pneumatic
tires at all times. Do not underinflate or overinflate your tires. Low pressure may result in
loss of control, and overinflated tires may burst. Failure to maintain 30-35 psi tire pressure
in pneumatic tires at all times may result in tire and/or wheel failure, causing serious
personal injury and/or damage to your scooter.
WARNING! Inflate your scooter tires from a regulated air source with an available pressure
gauge. Inflating your tires from an unregulated air source could overinflate them, resulting
in a burst tire and/or personal injury.
WEIGHT LIMITATIONS
Your scooter is rated for a maximum weight capacity. Refer to the specifications table for information.
WARNING! Exceeding the weight capacity voids your warranty and may result in personal
injury and damage to your scooter. Pride will not be held responsible for injuries and/or
property damage resulting from failure to observe weight limitations.
WARNING! Do not carr y passengers on your scooter. Carrying passengers may result in
personal injury and/or property damage.
INCLINE INFORMATION
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe
access. Some ramps may have turning switchbacks (180-degree turns) that require you to have good
cornering skills on your scooter.
n Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
n Take wide swings with your scooter around any tight corners. If you do that, the scooters rear wheels
will follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.
n When driving down a ramp, keep the scooters speed adjustment set to the slowest speed setting to
ensure a safely controlled descent.
n Avoid sudden stops and starts.
6
www.pridemobility.com Maxima
II. SAFETY
When climbing an incline, try to keep your scooter moving. If you must stop, start up again slowly, and then
accelerate cautiously. When driving down an incline, do so by setting the speed adjustment dial to the
slowest setting and driving in the forward direction only. If your scooter starts to move down the incline
faster than you anticipated or desired, allow it to come to a complete stop by releasing the throttle control
lever. Then push the throttle control lever forward slightly to ensure a safely controlled descent.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of the
incline. Drive your scooter straight up the incline. This greatly reduces the possibility of
a tip or a fall. Always exercise extreme caution when negotiating an incline.
WARNING! Do not drive your scooter across the side of an incline or diagonally up or
down a hill; do not stop, if possible, while driving up or down an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas
covered with snow, ice, cut grass, or wet leaves).
WARNING! When on any sort of an incline or decline, never place the scooter in freewheel
mode while seated on it or standing next to it.
WARNING! Even though your scooter is capable of climbing slopes greater than those
illustrated in figure 1 do not, under any circumstances, exceed the incline guidelines or
any other specifications presented in this manual. Doing so could cause instability in
your scooter, resulting in personal injury and/or damage to your scooter.
Handicap public access ramps are not subject to government regulation in all countries, and therefore do
not necessarily share the same standard percent of slope. Other inclines may be natural or, if man-made,
not designed specifically for scooters. Figure 1 illustrates your scooters stability and its ability to climb
grades under various weight loads and under controlled testing conditions.
These tests were conducted with the scooters seat in the highest position and adjusted rearward on the seat
base to its farthest rearward position. Use this information as a guideline. Your scooters ability to travel up
inclines is affected by your weight, your scooters speed, your angle of approach to the incline, and your
scooter setup.
200-250 lbs.
150 lbs.
7°, 12.3%
Figure 1. Maximum Recommended Incline Angles
WARNING! Any attempt to climb or descend a slope steeper than what is shown in figure
1 may put your scooter in an unstable position and cause it to tip, resulting in personal
injury.
6°, 10.5%
300-350 lbs.
400-450 lbs.
4.5°, 7.5%
5°, 8.7%
Maxima www.pridemobility.com
7
II. SAFETY
When you approach an incline, it is best to lean forward. See figures 2 and 2A. This shifts the center of
gravity of you and your scooter toward the front of the scooter for improved stability.
Figure 2. Normal Driving Position
Figure 2A. Increased Stability Driving Position
CORNERING INFORMA TION
Excessively high cornering speeds can create the possibility of tipping. Factors which affect the possibility
of tipping include, but are not limited to, cornering speed, steering angle (how sharply you are turning),
uneven road surfaces, inclined road surfaces, riding from an area of low traction to an area of high traction
(such as passing from a grassy area to a paved area especially at high speed while turning), and abrupt
directional changes. High cornering speeds are not recommended. If you feel that you may tip over in a
corner, reduce your speed and steering angle (i.e., lessen the sharpness of the turn) to prevent your scooter
from tipping.
WARNING! When cornering sharply, reduce your speed. When using your scooter at higher
speeds, do not corner sharply. This greatly reduces the possibility of a tip or fall. To avoid
personal injury or property damage, always exercise common sense when cornering.
BRAKING INFORMATION
Your scooter is equipped with these powerful brake systems:
n Regenerative: Uses electricity to rapidly slow the vehicle when the throttle control lever returns to the
center/stop position.
n Disc Park Brake: Activates mechanically after regenerative braking slows the vehicle to near stop, or
when power is removed from the system for any reason.
8
www.pridemobility.com Maxima
II. SAFETY
OUTDOOR DRIVING SURFACES
Your scooter is designed to provide optimum stability under normal driving conditionsdry, level surfaces
composed of concrete, blacktop, or asphalt. However, Pride recognizes that there will be times when you
will encounter other surface types. For this reason, your scooter is designed to perform admirably on packed
soil, grass, and gravel. Feel free to use your scooter safely on lawns and in park areas.
n Reduce your scooters speed when driving on uneven terrain and/or soft surfaces.
n Avoid tall grass that can become tangled in the running gear.
n Avoid loosely packed gravel and sand.
n If you feel unsure about a driving surface, avoid that surface.
PUBLIC STREETS AND ROADWAYS
WARNING! You should not operate your scooter on public streets and roadways. Be
aware that it may be difficult for traffic to see you when you are seated on your scooter.
Obey all local pedestrian traffic rules. Wait until your path is clear of traffic, and then
proceed with extreme caution.
STATIONARY OBSTACLES (STEPS, CURBS, etc.)
WARNING! Do not drive near raised surfaces, unprotected ledges, and/or drop-offs (curbs,
porches, stairs, etc.).
WARNING! Do not attempt to have your scooter climb or descend an obstacle that is
inordinately high. Serious personal injur y and/or damage may result.
WARNING! Do not attempt to have your scooter proceed rearward down any step, curb, or
other obstacle. This may cause the scooter to tip and cause personal injury.
WARNING! Be sure your scooter is traveling perpendicular to any curb you may be required
to ascend or descend. See figures 3 and 3A.
WARNING! Do not attempt to negotiate a curb that has a height greater than 2 in.
Figure 3. Correct Curb Approach
Maxima www.pridemobility.com
Figure 3A. Incorrect Curb Approach
9
II. SAFETY
INCLEMENT WEATHER PRECAUTIONS
WARNING! Pride recommends that you do not operate your scooter in icy or slipper y
conditions or on salted surfaces (i.e., walks or roads). Such use may result in an accident,
personal injury, or adversely affect the performance and safety of your scooter.
WARNING! Do not operate or store your scooter where it may be exposed to inclement
weather conditions such as rain, snow, mist, and below freezing temperatures (such as
storage on an outside car/van lift). Attempting to operate the scooter in such conditions
can damage the electronics and potentially result in loss of control.
FREEWHEEL MODE
Your scooter is equipped with a manual freewheel lever that, when pulled back, allows the scooter to be
pushed. For more information about how to place your scooter into and out of freewheel mode, see V. Your
Scooter.
WARNING! When your scooter is in freewheel mode, the braking system is disengaged.
n Disengage the drive motor only on a level surface.
n Ensure the key is removed from the key switch.
n Stand behind the scooter to engage or disengage freewheel mode. Never sit on a
scooter to do this.
n After you have finished pushing your scooter, always return it to the drive mode to lock
the brakes.
Failure to heed the above could result in personal injury and/or damage to your scooter.
An added feature built into your scooter is push-too-fast protection which safeguards the scooter against
gaining excessive speed while in freewheel mode.
Push-too-fast operates differently depending on which of two conditions exists:
n If the key is switched off while in freewheel mode, the scooters controller activates regenerative
braking when the scooter is pushed faster than a maximum threshold which has been preprogrammed.
In this case, the controller is acting as a speed governor.
n If the key is switched on while in freewheel mode, you will encounter considerable resistance at any
speed.
This prevents the scooter from gaining unwanted momentum should the manual freewheel lever inad
vertently be released while driving the scooter.
10
www.pridemobility.com Maxima
II. SAFETY
ST AIRS AND ESCALA T ORS
Scooters are not designed to travel up or down stairs or escalators. Always use an elevator.
WARNING! Do not use your scooter to negotiate steps or escalators. You may cause
injury to yourself and to others and/or damage your scooter.
DOORS
n Determine if the door opens toward or away from you.
n Use your hand to turn the knob or push the handle or push-bar.
n Drive your scooter gently and slowly forward to push the door open. Or drive your scooter gently and
slowly rearward to pull the door open.
ELEVATORS
Modern elevators have a door edge safety mechanism that, when pushed, reopens the door(s).
n If you are in the doorway of an elevator when the door(s) begin to close, push on the rubber door edge
or allow the rubber door edge to contact the scooter and the door will reopen.
n Use care that pocketbooks, packages, or scooter accessories do not become caught in elevator doors.
LIFT/ELEVATION PRODUCTS
If you will be traveling with your scooter, you may find it necessary to use a lift/elevation product to aid in
transportation. Pride recommends that you closely review the instructions, specifications, and safety information set forth by the manufacturer of the lift/elevation product before using that product.
WARNING! Never sit on your scooter when it is being used in connection with any type of
lift/elevation product. Your scooter was not designed for such use, and any damage or
injury incurred from such use is not the responsibility of Pride.
BATTERIES
In addition to following the warnings below, be sure to comply with all other battery handling information.
WARNING! Scooter batteries are heavy (refer to specifications table). Lifting weight beyond
your capacity could result in personal injury. If necessary, get someone physically able
to lift the scooter batteries for you.
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wash hands after handling.
WARNING! Always protect the batteries from freezing and never charge a frozen battery.
Charging a frozen battery may result in personal injury and/or damage to the battery.
WARNING! RED (+) cables must be connected to positive (+) battery terminals/posts.
BLACK (-) cables must be connected to negative (-) batter y terminals/posts. Failure to
connect your battery cables in the proper manner may result in personal injury and/or
damage to your scooter. REPLACE cables immediately if damaged.
BATTERY DISPOSAL AND RECYCLING
If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag and call your authorized Pride Provider for instructions on disposal. Your authorized Pride Provider will also have the necessary information on battery recycling, which is our recommended course of action.
Maxima www.pridemobility.com
11
II. SAFETY
MOTOR VEHICLE TRANSPORT
Currently, there are no standards approved for tie-down systems in a moving vehicle of any type to transport a person while seated in a scooter.
Although your scooter may be equipped with a positioning belt, this belt is not designed to provide proper
restraint during motor vehicle transport. Anyone traveling in a motor vehicle should be properly secured in
the motor vehicle seat with safety belts fastened securely.
WARNING! Do not sit on your scooter while it is in a moving vehicle. Personal injury and/
or property damage may result.
WARNING! Always be sure your scooter and its batteries are properly secured when it is
being transported. Failure to do so may result in personal injury and/or damage to your
scooter.
PREVENTING UNINTENDED MOVEMENT
WARNING! If you anticipate being seated in a stationary position for an extended period
of time, turn off the power. This will prevent unexpected motion from inadvertent throttle
control lever contact. Failure to do so may result in personal injury.
GETTING ONTO AND OFF OF YOUR SCOOTER
Getting onto and off of your scooter requires a good sense of balance. Please observe the following safety
tips when getting onto and off of your scooter:
n Ensure that your scooter is not in freewheel mode. See V. Your Scooter.
n Make certain that the seat is locked into place and the key is removed from the key switch.
n The seat armrests can be flipped up to make getting onto and off of the scooter easier.
WARNING! Position yourself as far back as possible in the scooter seat to prevent the
scooter from tipping and causing injury.
WARNING! Avoid using your armrests for weight bearing purposes. Such use may cause
the scooter to tip and cause personal injury.
WARNING! Avoid putting all of your weight on the floorboard. Such use may cause the
scooter to tip and cause personal injury.
REACHING AND BENDING
Avoid reaching or bending while driving your scooter. When reaching, bending, or leaning while seated on
your scooter, it is important to maintain a stable center of gravity and keep the scooter from tipping. Pride
recommends that the scooter user determine his/her personal limitations and practice bending and reaching
in the presence of a qualified healthcare professional.
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the
floor by reaching down between your knees. Movements such as these may change your
center of gravity and the weight distribution of the scooter and cause your scooter to tip,
possibly resulting in personal injury. Keep your hands away from the tires when driving.
12
www.pridemobility.com Maxima
II. SAFETY
POSITIONING BELTS
Your authorized Pride Provider, therapist(s), and other healthcare professionals are responsible for determining your requirement for a positioning belt in order to operate your scooter safely.
WARNING! If you require a positioning belt to safely operate your scooter, make sure it is
fastened securely. Serious personal injury may result if you fall from the scooter.
PRESCRIPTION DRUGS/PHYSICAL LIMITATIONS
The scooter user must exercise care and common sense when operating his/her scooter. This includes awareness of safety issues when taking prescribed or over-the-counter drugs or when the user has specific physical
limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter
medication or if you have certain physical limitations. Some medications and limitations
may impair your ability to operate your scooter in a safe manner.
ALCOHOL
The scooter user must exercise care and common sense when operating his/her scooter. This includes
awareness of safety issues while under the influence of alcohol.
WARNING! Do not operate your scooter while you are under the influence of alcohol, as
this may impair your ability to drive safely.
Maxima www.pridemobility.com
13
III. EMI/RFI
EMI/RFI WARNINGS
Laboratory tests performed by the Food and Drug Administration (FDA) have shown that radio waves can
cause unintended motion of electric mobility vehicles. Radio waves are a form of electromagnetic energy
(EM). When electromagnetic energy adversely affects the operation of an electrical device, that adverse
effect is called Electromagnetic Interference (EMI) or Radio Frequency Interference (RFI).
EMI/RFI FREQUENTLY ASKED QUESTIONS (FAQS)
The following FAQs summarize what you should kn
risk that EMI/RFI will adversely affect your mobility vehicle.
Where do radio waves come from?
Radio waves are emitted from the antennas of cellular phones, mobile two-way radios (such as walkietalkies and CBs), radio stations, TV stations, amateur radio (HAM) transmitters, wireless computer links,
microwave sources, and paging transmitters. Radio waves are a form of electromagnetic energy (EM). EM
is more intense closer to transmitting antennas, which are sources of emission. The greater the transmission strength, the greater the concern to electric mobility vehicle users.
If EMI/RFI affects my mobility vehicle, what kind of motion should I expect?
This is difficult to predict. The answer would depend on a number of factors:
n The strength of the radio waves.
n The construction of your particular mobility vehicle.
n The location of your mobility vehicle (whether it is on the level ground or on an incline).
n Whether or not your mobility vehicle is in motion.
ow about EMI/RFI. Use this information to minimize the
The motion of any electric mobility vehicle affected by EMI/RFI can be erratic. The mobility vehicle may
come to a sudden stop or move in an uncontrolled manner. Also, it is possible for EMI/RFI to release the
brakes of an electric mobility vehicle. Some intense EMI/RFI can even damage the control system components of an electric mobility vehicle.
Is there any way to know for certain whether or not radio waves are the cause of any unintended
mobility vehicle motion?
Unfortunately, EMI/RFI may be difficult to recognize, because the signals from radio sources are invisible
and may be intermittent. However, the FDA recommends that you report all incidents of unintended motion
or unintended brake release of your mobility vehicle to its manufacturer and, if possible, determine whether
or not there was a radio wave source nearby at the time of the incident.
One precaution you can take against unintended motion of your mobility vehicle is to make certain that you
or someone else is not the cause of the unintended motion.
n Turn off your mobility vehicle by removing the key from the key switch when you are getting onto or
off of your mobility vehicle.
n Never leave the key in the key switch of an unattended mobility vehicle.
n By following these steps, you greatly reduce the risk of you or anyone else inadvertently bumping the
throttle control levers and causing the mobility vehicle to move unintentionally.
Has anyone been injured by the erratic, unintended motion of an electric mobility vehicle?
The FDA has reports of injuries that resulted from uncontrolled motion of electric mobility vehicles, but it
is not clear just how many of those injuries were actually caused by EMI/RFI.
14
www.pridemobility.com Maxima
III. EMI/RFI
Are all electric mobility vehicles susceptible to EMI/RFI?
Each make and model of electric mobility vehicle differs in its ability to resist EMI/RFI. Every mobility
vehicle has a particular level of resistance to EMI/RFI. This resistance is measured in volts per meter (V/
m). A higher resistance level offers greater protection against EMI/RFI. In other words, an electric mobility
vehicle with a high resistance level is less likely to be affected by a strong radio source than is an electric
mobility vehicle with a low resistance level.
What is the FDA doing about the problem?
The FDA has written to electric mobility vehicle manufacturers and requested that those manufacturers test
their new mobility vehicle models to be certain that they provide a reasonable degree of resistance against
EMI/RFI. The FDA has stated that all newly manufactured electric mobility vehicle models should have a
resistance level of at least 20 V/m. This level of resistance provides a reasonable degree of protection
against the common sources of EMI/RFI.
The FDA has also requested or recommended that:
n Electric mobility vehicle manufacturers clearly label new products with their resistance level or state
that the resistance level is not known.
n The labeling or informational material supplied with new electric mobility vehicles must explain what
the resistance level means and warn users about the possibility of EMI/RFI and how to avoid it.
n Electric mobility vehicle manufacturers undertake an educational program to inform electric mobility
vehicle users and their caregivers about the problems associated with EMI/RFI and about the actions
they can take to minimize the risk of EMI/RFI.
n While there is no exact way to tell if your mobility vehicle is totally safe, an immunity level of 20 V/m
is generally achievable and useful. This product has been tested and passed at an immunity level of 20 V/m.
What can I do to find out if my mobility vehicle is likely to be affected by EMI/RFI?
If you have had your mobility vehicle for some time and have not experienced any unintended motion, it is
not likely that you will have a problem in the future. However, it is always possible that EMI/RFI problems
could arise if you are close to a source of radio waves. Therefore, it is very important for you to be alert to
this possibility. The mobility vehicle meets or exceeds a resistance level of at least 20 V/m.
What can I do to reduce the risk of my mobility vehicle being affected by EMI/RFI?
Here are some precautions you can take:
n Do not turn on or use hand-held personal communications devices, such as citizens band (CB) radios
and cellular phones, while your mobility vehicle is turned on.
n Be aware of nearby radio wave transmitters, such as radio or TV stations and hand-held or mobile two-
way radios. Try not to operate your mobility vehicle too close to those transmitters. For example, if you
are on an electric mobility vehicle with a resistance level of at least 20 V/m, you should remain at least
three feet from a hand-held two-way radio and at least ten feet from a mobile two-way radio.
n Be aware that adding accessories and/or components, or modifying your mobility vehicle in any way,
may change its EMI/RFI resistance level and may make it more susceptible to interference from radio
wave sources.
What should I do if my mobility vehicle moves unexpectedly?
If unintended motion or unintended brake release occurs, turn off your mobility vehicle (by removing the
key) as soon as it is safe to do so.
If my mobility vehicle moves unintentionally, where should I report the incident?
Call Pride Customer Care at 1-800-424-8205 to report the incident.
Maxima www.pridemobility.com
15
IV. SPECIFICATIONS
18.5"
8"
37.5"-40.5"
16"-18"
4.5"
4-Wheel Turning Radius 58"
Figure 4. Scooter Dimensions
10"
FRONT
Figure 4A. Tire Dimensions
3"
22"
24"-28"
26"
18"
3- Wheel 47"
4- Wheel 47.5"
3-Wheel Turning Radius 52"
4"
10"
REAR
16
www.pridemobility.com Maxima
IV. SPECIFICATIONS
M od el N umbers
A v a ilable C o lo rs
Ov erall Len gth
Ov erall W idth
T o ta l Weigh t Without B a tte r ie s
Hea viest Piece W h en D isassem b led
Turning Radius
Speed (maximum)
R ange P er Charge* (W ith 32 AH batteries) Up to 2 0 miles, (With 55 A H batteries) Up to 30 miles
Gr oun d C learance
Weight Capacity
Standard Seating
Standard Seat Weight
D rive System
Dual Braking System
Tires
Battery R equ irem e nts
Battery Weight
Battery Charger
3-wheel: SC900
4-wheel: SC940
Painted: Candy Apple Red, Forest Green, Viper Blue, Black Onyx
3-wheel: 47 in.
4-wheel: 47.5 in.
26 in.
3-wheel: 173.5 lbs.
4-wheel: 189 lbs.
Rear fram e: 70 lbs.
3-wheel: 52 in.
4-wheel: 58 in.
Variable up to 5.25 m ph
4.5 in.
450 lbs.
Type: DX contour medium back
Dim ensions: 22 in. width x 18 in. depth (usable) x 18.5 in. height (usable)
M aterial: Gray, Beige, or Black v inyl or Gray fabric
45 lbs.
Rear-w h eel drive, sealed transaxle with a 24-v olt DC motor
Electronic, regenerative, and electromech anical
Type: solid; front: 3 in. x 10 in., rear: 4 in. x 10 in.
Type: Two 12-volt deep cycle (AG M or Gel-Cell)
Siz e : (U-1) 3 2 AH , (NF-2 2 ) 5 5 AH
A pproximately: (32 AH ) 25 lbs. each, (55A H ) 37 lbs. each
O ff-board c h a r g er
*Varies with user weight, terrain type, battery charge, battery condition, and tire condition.
Maxima www.pridemobility.com
17
V. YOUR SCOOTER
CONTROL CONSOLE ASSEMBLY
The control console assembly houses all of the controls you need to drive your scooter, including the key
switch, speed adjustment dial, status LED, throttle control lever, battery condition meter, horn buttons,
light switch, turn signal buttons, and the hazard lights switch. See figure 5.
WARNING! Do not expose the control console assembly to moisture. In the event that the
control console assembly does become exposed to moisture, do not attempt to operate
your scooter until the control console assembly has dried thoroughly.
BATTER Y CONDITION METER
STATUS LED
SPEED ADJUSTMENT DIAL
KEY
KEY SWITCH
LEFT TURN SIGNAL BUTTON
HAZARD
LIGHTS
SWITCH
HORN BUTTON
THROTTLE CONTROL LEVER (REVERSE)
Figure 5. Control Console Assembly
THROTTLE CONTROL LEVER (FORWARD)
OFF-BOARD CHARGER PORT
RIGHT TURN SIGNAL BUTTON
LIGHT
SWITCH
HORN BUTTON
Key Switch
n Fully insert the key into the key switch and turn it clockwise to power up (turn on) your scooter.
n Turn the key counterclockwise to power down (turn off) your scooter.
WARNING! If the key is moved to the off position while your scooter is in motion, the
electronic brakes engage and your scooter comes to an abrupt stop!
Speed Adjustment Dial
This adjustment dial enables you to preselect and limit your scooters top speed.
n
The image of the tortoise represents the slowest speed setting.
n The image of the hare represents the fastest speed setting.
18
www.pridemobility.com Maxima
V. YOUR SCOOTER
Status LED
The Status LED alerts you to electrical problems that may occur with the scooter. The LED remains constantly lit
while your scooter is on. If the scooter develops an electrical problem, the status LED will flash a code. See X.
Basic Troubleshooting for troubleshooting flash codes.
Throttle Control Lever
This lever allows you to control the forward speed and the reverse speed of your scooter up to the maximum speed
you preset with the speed adjustment dial.
n
Place your right hand on the right handgrip and your left hand on the left handgrip.
n Use your right thumb to push the right side of the lever to disengage your scooters brakes and move forward.
n Release the lever and allow your scooter to come to a complete stop before pushing the other side of the
lever to move in reverse.
n When the throttle control lever is completely released, it automatically returns to the center stop
position and engages your scooters brakes.
Battery Condition Meter
The battery condition meter on the control console assembly indicates the approximate strength of your
batteries using a color code. Green indicates fully charged batteries, yellow a draining charge, and red
indicates that an immediate recharge is necessary.
Horn Buttons
The key must be inserted and turned clockwise for the horn to be operational.
n These buttons activate a warning horn.
n Do not hesitate to use the warning horn when its use could prevent accident or injury.
Light Switch
This switch controls your scooters lighting system. Toggle this switch to turn on and turn off the lights.
Turn Signal Buttons
Use these buttons to turn on the left and right turn signal lights.
n Press the appropriate turn signal button once to activate it.
n Your scooters turn signals are timed to shut off automatically.
Hazard Lights Switch
This switch activates the 4-way flashers on your scooter. Toggle this switch to turn on and turn off the
lights.
Off-Board Charger Port
The scooters off-board charger plugs into this port.
Maxima www.pridemobility.com
19
V. YOUR SCOOTER
REAR SECTION
The manual freewheel lever, the anti-tip wheels, the motor/transaxle assembly (not shown), the electronics
module, the batteries (not shown), the main circuit breaker (reset button), the fuses, and the ammeter are
located on the rear section of your scooter. See figure 6. Refer to IX. Disassembly and Assembly for
instructions on removing the rear shroud.
RUNNING
CHARGER POWER CORD STORAGE COMP ARTMENT
AMMETER
ELECTRONICS MODULE
(REMOVE REAR SHROUD
TO VIEW ENTIRE MODULE)
LIGHT FUSE
RIGHT RUN-
NING LIGHT
LIGHT BULB
RIGHT TURN
SIGNAL FUSE
TURN SIGNAL
LIGHT BULB
LIGHT COVER
MANUAL FREEWHEEL
LEVER
MAIN CIRCUIT BREAKER (RESET BUTTON)
FUSES
ANTI-TIP WHEEL
Figure 6. Rear Section
Main Circuit Breaker (Reset Button)
When the voltage in your scooters batteries becomes low or your scooter is heavily strained because of
excessive loads or steep inclines, the main circuit breaker may trip to protect your scooters motor and
electronics from damage.
n The main circuit breaker reset button pops out when the breaker trips.
n When the breaker trips, the entire electrical system of your scooter shuts down.
n Allow a minute or two for your scooters electronics to rest.
n Push in the reset button to reset the breaker.
n If the breaker trips frequently, you may need to charge your batteries more often. You may also need to
have your authorized Pride Provider perform a load test on your scooters batteries.
n If the main circuit breaker trips repeatedly, see your authorized Pride Provider for service.
20
www.pridemobility.com Maxima
V. YOUR SCOOTER
Manual Freewheel Lever
Whenever you need or want to push your scooter for short distances, you can put it in freewheel mode.
n Pull up on the manual freewheel lever to disable the drive system and the brake system.
n You may push your scooter.
n Push down on the manual freewheel lever to reengage the drive system and the brake system and take
your scooter out of freewheel mode.
WARNING! When your scooter is in freewheel mode, the braking system is disengaged.
n Disengage the drive motors only on a level surface.
n Ensure the key is removed from the key switch.
n Stand behind the scooter to engage or disengage freewheel mode. Never sit on a
scooter to do this.
n After you have finished pushing your scooter, always return it to the drive mode to lock
the brakes.
Failure to heed the above could result in personal injury and/or damage to your scooter.
OPERATION OF THE MANUAL FREEWHEEL LEVER
n Only put the scooter in freewheel mode when on a flat surface with the key removed.
n Pull UP FIRMLY on the manual freewheel lever when putting the scooter into freewheel
mode.
n Push DOWN FIRMLY to engage drive mode.
Anti-Tip Wheels
WARNING! Do not remove the anti-tip wheels or modify your scooter in any way that is
not authorized by Pride.
The front (not shown) and rear anti-tip wheels are an integral and important safety feature of your scooter.
Do not, under any circumstances, remove the anti-tip wheels from your scooter.
Motor/Transaxle Assembly (Not Shown)
The motor/transaxle assembly is the electromechanical unit that converts the electrical energy of your
scooters batteries into the controlled mechanical energy that drives the scooters wheels.
Electronics Module
The electronics module houses all of the scooters harness mating plugs and electronic components for
charging the batteries.
Batteries (Not Shown)
The batteries store the electrical energy that powers your scooter. See VI. Batteries and Charging.
Fuses
The fuses help protect your scooters lighting, and control console assembly systems from receiving an overload of
electrical current. The fuses used in the scooter are the same type automobiles use.
If a fuse must be replaced, use only the specified amp fuse. See XI. Care and Maintenance.
Maxima www.pridemobility.com
21
V. YOUR SCOOTER
HERCULES DOCKING DEVICE
Your scooter is equipped with a Hercules 3000 docking device. See figure 7. In order to utilize the docking
device, it is necessary to purchase an insert (T-bar or Bullnose and C-arm) that, when used with the Hercules 3000, will lift your scooter.
Contact your authorized Pride Provider for more information about the Hercules 3000 docking device.
DOCKING DEVICE
Figure 7. Hercules 3000 Docking Device
22
www.pridemobility.com Maxima
VI. BATTERIES AND CHARGING
Your scooter requires two long-lasting, 12-volt, deep-cycle batteries that are sealed and maintenance free.
They are recharged by an onboard charging system.
n Charge your scooters batteries prior to using it for the first time.
n Keep the batteries fully charged to keep your scooter running smoothly.
READING YOUR BA TTERY VOLTAGE
The battery condition meter on the tiller console indicates the approximate strength of your batteries using
a color code. Green indicates fully charged batteries, yellow a draining charge, and red indicates that an
immediate recharge is necessary. See figure 8. To ensure the highest accuracy, the battery condition meter
should be checked while operating your scooter at full speed on a dry, l level surface.
You can also check the charging status of the batteries by the ammeter, located at the rear of the scooter.
The charger power cord must be plugged into a standard wall outlet in order to obtain a reading. When the
amperage reading is at or near zero amps, charging is complete. See figure 9.
CHARGING YOUR BA TTERIES
WARNING! Never use an extension cord to plug in
your battery charger. Plug the charger directly into
a properly wired standard wall outlet.
WARNING! Removal of the grounding prong can
create an electrical hazard. If necessary properly
install an approved 3-pronged adaptor to an electrical
outlet having 2-pronged plug access. Failure to heed
could result in personal injury and or property
damage.
Follow these easy steps to charge your batteries safely:
1. Position your scooter close to a standard wall outlet.
2. Remove the key from the key switch.
3. Make certain that the manual freewheel lever is in the drive (pushed
down) position.
4. Plug the 3-pin charger power cord into the off-board charger port.
5. Extend the charger power cord and plug it into the wall outlet.
6. Turn the charger on.
7. When the batteries are fully charged, turn the charger off and unplug the charger power cord from the wall outlet and then from
the charger power cord receptacle.
NOTE: There is a charger inhibit function on your scooter. The scooter
will not run and the battery condition meter will not operate while the
batteries are charging.
Figure 8. Battery Condition Meter
Figure 9. Ammeter Indicates Batteries
Are Fully Charged
Maxima www.pridemobility.com
23
VI. BATTERIES AND CHARGING
BATTERIES AND CHARGING-FREQUENTLY ASKED QUESTIONS (FAQS)
How does the charger work?
When your scooters battery voltage is low, the charger works harder, sending more electrical current to the batteries
to bring up their charge. As the batteries approach a full charge, the charger sends less and less electrical current.
When the batteries are fully charged, the current sent from the charger is at nearly zero amperage. Therefore, when
the charger is plugged in, it maintains the charge on your scooters batteries, but does not overcharge them. We do
not recommend that you charge your scooters batteries for more than 24 consecutive hours.
What if my scooters batteries wont charge?
n Ensure the red (+) and black (-) battery cables are connected properly to the battery terminals.
n Ensure both battery harnesses that extend from the batteries are plugged into their mating harness
leading to the charger.
n Ensure both ends of the charger power cord are inserted fully.
Can I use a different charger?
For the safest, most efficient, and balanced charging of your scooters batteries, we prefer and highly
recommend simultaneous charging of both batteries with the onboard battery charger.
How often must I charge the batteries?
Two major factors must be considered when deciding how often to charge your scooters batteries:
n All day scooter use on a daily basis.
n Infrequent or sporadic scooter use.
With these considerations in mind, you can determine how often and for how long you should charge your
scooters batteries. We designed the onboard charger so that it will not overcharge your scooters batteries.
However, you may encounter some problems if you do not charge your batteries often enough and if you do
not charge them on a regular basis. Following the five guidelines below will provide safe and reliable
battery operation and charging.
n If you use your scooter daily, charge its batteries as soon as you finish using it for the day. Your scooter
will be ready each morning to give you a full day of service. We recommend that you charge your
scooters batteries for 8 to 14 hours after daily use.
n If you use your scooter once a week or less, charge its batteries at least once a week for 12 to 14 hours at a time.
n Keep your scooters batteries fully charged.
n Avoid deeply discharging your scooters batteries.
How can I ensure maximum battery life?
Fully charged deep-cycle batteries provide reliable performance and extended battery life. Keep your scooters
batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently
charged, or stored without a full charge may be permanently damaged, causing unreliable performance and
limited service life.
24
www.pridemobility.com Maxima
VI. BATTERIES AND CHARGING
How can I get maximum range or distance per charge?
Rarely will you have ideal driving conditionssmooth, flat, hard driving surfaces with no wind or curves. Often, you
will face hills, pavement cracks, uneven and loosely packed surfaces, curves, and wind, all of which affect the distance
or running time per battery charge. Below are a few suggestions for obtaining the maximum range per battery charge.
n Always fully charge your scooters batteries prior to daily use.
n Maintain 30-35 psi (pounds per square inch) in each tire.
n Plan your route ahead to avoid as many hills, cracked, broken, or soft surfaces as possible.
n Limit your baggage weight to essential items.
n Try to maintain an even speed while your scooter is in motion.
n Avoid stop-and-go driving.
What type and size of battery should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are deepcycle batteries that are similar in performance. Do not use wet-cell batteries, which have removable caps.
NOTE: Sealed batteries are not serviceable. Do not remove the caps.
Use these specifications to reorder batteries from your authorized Pride Provider:
BATTERY SPECIFICATIONS
Type:
Size:
Voltage:
Amperage:
WARNING! Corrosive chemicals contained in batteries. Use only AGM or Gel-Cell batteries
to reduce the risk of leakage or explosive conditions.
To change a battery in your scooter:
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wash hands after handling.
Deep-cycle (AGM or Gel-Cell)
U-1, NF-22
12 volts each
32 AH,55 AH (amp hours)
1. Remove the seat and rear shroud.
2. Disconnect the battery tie-down strap.
3. Disconnect the battery harness.
4. Disconnect the battery cables from the battery terminals.
5. Remove the old battery.
6. Place a new battery in the battery well.
7. Connect the red battery cable to the positive (+) battery terminal.
8. Connect the black battery cable to the negative (-) battery terminal.
9. Reconnect the battery harness.
10. Reconnect the battery tie-down strap.
11. Reinstall the rear shroud and seat.
Maxima www.pridemobility.com
25
VI. BATTERIES AND CHARGING
BATTERY DISPOSAL AND RECYCLING
If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag and call your authorized Pride Provider for instructions on disposal. Your authorized Pride Provider will also have the necessary information on battery recycling, which is our recommended course of action.
Why do my new batteries seem weak?
Deep-cycle batteries employ a different chemical technology than that used in car batteries, nickel-cadmium batteries (nicads), and other common battery types. Deep-cycle batteries are specifically designed to
provide power, drain down their charge, and then accept a relatively quick recharge.
We work closely with our battery manufacturer to provide batteries that best suit your scooters specific
electrical demands. Fresh batteries arrive daily at Pride and are shipped fully charged to our customers.
During shipping, the batteries may encounter temperature extremes that can influence their initial performance. Heat diminishes the charge on the battery; cold slows the available power and extends the time
needed to recharge the battery.
It may take a few days for the temperature of your scooters batteries to stabilise and adjust to their new
room or ambient temperature.
More importantly, it takes a few charging cycles (partial draining followed by full recharging) to establish
the critical chemical balance that is essential to a deep-cycle batterys peak performance and long life.
Follow these steps to properly break in your scooters new batteries for maximum efficiency and service
life.
1. Fully recharge any new battery prior to its initial use. This charging cycle brings the battery up to about
88% of its peak performance level.
2. Operate your new scooter in familiar and safe areas. Drive slowly at first, and do not travel too far from
your home or familiar surroundings until you have become accustomed to your scooters controls and
have properly broken in your scooters batteries.
3. Fully recharge the batteries. They should be at over 90% of their peak performance level.
4. Operate your scooter again.
5. Fully recharge the batteries again.
6. After four or five charging cycles, the batteries are able to receive a charge of 100% of their peak
performance level and are able to last for an extended period of time.
What about public transportation?
If you intend to use public transportation with your scooter, you must contact the transportation Provider in
advance to determine their specific requirements.
26
www.pridemobility.com Maxima
VII. OPERATION
BEFORE GETTING ON YOUR SCOOTER
n Have you fully charged the batteries? See VI. Batteries and Charging.
n Is the manual freewheel lever in the drive (down) position? Never leave the manual freewheel lever
pulled up unless you are manually pushing your scooter.
GETTING ONTO YOUR SCOOTER
1. Make certain that the key is removed from the key switch.
WARNING! Never attempt to board or exit your scooter without first removing the key
from the key switch. This will prevent the scooter from moving if accidental throttle
control lever contact is made.
2. Stand at the side of your scooter.
3. Push down on the seat lock lever and rotate the seat until it is facing you.
4. Make certain that the seat is locked securely in position.
5. Position yourself comfortably and securely in the seat.
6. Push down on the seat lock lever and rotate the seat until you are facing forward.
7. Make certain that the seat is locked securely in position.
8. Make certain that your feet are safely on the floorboard.
PRE-RIDE ADJUSTMENTS AND CHECKS
n Is the seat at the proper height? See VIII. Comfort Adjustments.
n Is the seat locked securely in place?
n Is the tiller at a comfortable setting and locked securely in place? See VIII. Comfort Adjustments.
n Is the key fully inserted into the key switch and turned clockwise to the on position? See V. Your
Scooter.
n Does the scooters horn work properly?
n Is your proposed path clear of people, pets, and obstacles?
n Have you planned your route to avoid adverse terrain and as many inclines as possible?
OPERATING YOUR SCOOTER
Keep both hands on the tiller and your feet on the floorboard at all times while operating your scooter. This
driving position gives you the most control over your vehicle.
n Set the speed adjustment dial to your desired speed.
n Press your thumb against the appropriate throttle control lever.
n The electromechanical disc park brake automatically disengages and the scooter accelerates smoothly
to the speed you preselected with the speed adjustment dial.
n Pull on the left handgrip to steer your scooter to the left.
n Pull on the right handgrip to steer your scooter to the right.
n Move the tiller to the center position to drive straight ahead.
n To stop, slowly release the throttle control lever. The electronic brakes will automatically engage when
your scooter comes to a stop.
NOTE: Your scooters reverse speed is slower then that of the forward speed you preset with the speed
adjustment dial.
Maxima www.pridemobility.com
27
VII. OPERATION
GETTING OFF OF YOUR SCOOTER
1. Bring your scooter to a complete stop.
2. Remove the key from the key switch.
3. Push down on the seat lock lever and rotate the seat until you are facing toward the side of your scooter.
4. Make certain that the seat is locked securely in position.
5. Carefully and safely get out of the seat and stand to the side of your scooter.
6. You can leave the seat facing to the side to facilitate boarding your scooter next time.
POWER DOWN TIMER FEATURE
Your scooter is equipped with an energy saving auto power down timer feature designed to preserve your
scooters battery life. If you mistakenly leave the key in the key switch and in the on position but do not
use your scooter for approximately 20 minutes, the scooters controller shuts down automatically. Although
the controller is shut down, power will still be supplied to the scooters lighting system.
If the power down timer feature takes effect, perform the following steps to resume normal operation.
1. Turn the key to the off position.
2. Turn the key back to the on position.
28
www.pridemobility.com Maxima
VIII. COMFORT ADJUSTMENTS
TILLER ANGLE ADJUSTMENT
WARNING! Remove the key from the key switch
before adjusting the tiller or the seat. Never
attempt to adjust the tiller or the seat while the
scooter is in motion.
Your scooter is equipped with a pivoting tiller that allows adjustment
to several positions.
1. Lift the tiller adjustment lever. See figure 10.
2. Move the tiller to a comfortable position.
3. Release the tiller adjustment lever to secure the tiller in position.
SEAT LOCK LEVER
The seat lock lever locks the seat in one of four positions. See
figure 11.
1. Push the seat lock lever down to unlock the seat.
2. Rotate the seat to the desired position.
3. Release the seat lock lever to lock the seat securely in place.
FRONT-T O-BACK SEAT ADJUSTMENT
You can reposition the scooters seat forward or rearward to one of
three settings to adjust the distance between the seat and the tiller.
See figure 11.
1. Remove the seat from your scooter. See IX. Disassembly and
Assembly.
2. Remove the four bolts that fasten the seat to the seat platform.
3. Align the seat platform with the desired set of holes on the seat.
4. Install the four bolts securely.
ARMREST WIDTH ADJUSTMENT
The armrests can be adjusted inward or outward. See figure 11A.
1. Loosen the armrest adjustment knobs at the back of the seat
frame.
2. Slide the armrests in or out to the desired width.
3. Tighten the armrest adjustment knobs.
The armrests also pivot upward to make getting onto and off of
your scooter easier.
Figure 10. Tiller Adjustment Lever
SEAT LOCK LEVER
SEAT BOLTS
Figure 11. Seat Adjustments
UPPER POST
ADJUSTMENT
HOLES
ARMREST HEIGHT ADJUSTMENT
The height of both armrests can be adjusted upward or downward.
See figure 11A.
1. Remove the detent pin.
2. Raise or lower the armrest.
3. Reinsert the detent pin through the adjustment holes of
the upper and lower posts.
Maxima www.pridemobility.com
LOWER POST
DETENT PIN
ARMREST ADJUSTMENT KNOBS
Figure 11A. Armrest Adjustments
29
VIII. COMFORT ADJUSTMENTS
SEA TBACK ADJUSTMENT
The seatback may be positioned to four different
angles: 90°, 100°, 102° and 105°. See figure 12.
To adjust the seatback angle:
1. Loosen and remove the adjustment screws
from the seatback hinge on both sides of the
seat.
2. Reposition the seatback to the desired angle.
3. Align the adjustment holes from the upper
and lower hinge, so the adjustment screw can
easily pass through.
4. Reinsert both adjustment screws and tighten.
SEAT HEIGHT ADJUSTMENT
The seat can be repositioned to different heights.
See figure 13.
1. Remove the seat and shroud from your
scooter. See IX. Disassembly and
Assembly.
2. Loosen the nut and remove it from the bolt,
and remove the bolt and washers from the
lower seat post.
3. Raise or lower the upper seat post to the
desired seat height.
4. While holding the upper seat post at that
height, match up the holes in the upper seat
post with those of the lower seat post.
5. Fully insert the bolt, reinstall the washers,
and tighten the nut.
UPPER HINGE
100° ADJUSTMENT HOLE
ADJUSTMENT SCREW
102° ADJUSTMENT HOLE
105° ADJUSTMENT HOLE
90° ADJUSTMENT HOLE
LOWER HINGE
Figure 12. Seatback Hinge
UPPER SEA T POST
WASHER
WASHER
BOLT
NUT
LOWER SEAT POST
Note: Ensure both washers have been reinstalled
before fully tightening the nut.
6. Reinstall the rear shroud and the seat.
30
www.pridemobility.com Maxima
Figure 13. Seat Height Adjustment
VIII. COMFORT ADJUSTMENTS
POWER SEAT (OPTIONAL)
Your scooter may be equipped with a power seat. The power seat actuator is designed to raise or lower the
seat automatically with minimal effort on the part of the operator. See figure 14. The power seat switch is
located on the lower tiller just above the charger port.
Operating your power seat:
1. Release the throttle control lever.
2. Ensure your scooter is level and stationary.
3. Set the speed adjustment dial to the slowest setting
4. Toggle on the power seat switch that is located on the tiller console.
5. To raise the power seat, place your hands on the handgrips and use your thumb to push the right side of
the throttle control lever.
6. Release the throttle control lever when you have attained your desired height.
7. To lower the power seat, place your hands on the handgrips and use your thumb to push the left side of
the throttle control lever.
8. Ensure your seat is in the lowest position and release the throttle control lever.
9. Toggle off the power seat switch before you attempt to drive your scooter again.
WARNING! The power seat is intended for operation only while your scooter is stationary
and on a level surface. Its purpose is to aid you in reaching objects.
Strict adherence to the following safety rules is vital to your safety:
n Operate the power seat only on level ground.
n Do not attempt to operate the power seat switch with the throttle control
lever depressed.
n Do not attempt to raise or lower the seat while in motion!
n Do not operate your scooter with the power seat elevated.
n It is recommended that the scooter be driven only with the seat in the
lowest position.
Maxima www.pridemobility.com
Figure 14. Power Seat Actuator
31
I X . DISASSEMBLY AND ASSEMBLY
DISASSEMBLY
You can disassemble the scooter into seven pieces: the
seat, the front section, the rear section, the rear shroud,
REAR SECTION
FRONT SECTION
SEAT
the basket, and the batteries. See figure 15. Place the
scooter in an area where you have sufficient clearance
to move the parts around. You need about four or five
feet in all directions. You may need assistance to lift
some of the scooter components. See IV.
Specifications for individual component weights.
REAR SHROUD
Figure 15. The Maxima Disassembled
BASKET
BATTERIES
No tools are required to disassemble or assemble your scooter. Always disassemble or assemble your
scooter on a level, dry surface with sufficient room for you to work and move around your scooter. Keep in
mind that the disassembled sections of the scooter take up more floor space than the assembled scooter.
WARNING! Lifting weight beyond your physical capability may result in personal injury.
Ask for assistance when necessary while disassembling or assembling your scooter.
To disassemble:
1. Place the manual freewheel lever in the drive (down) position.
2. Coil the charger power cord and store it in the rear storage compartment.
3. Lift the seat straight up and off the scooter. See figure 16.
4. Gently lift the rear shroud off of the scooter. See figure 17.
Figure 16. Seat Removal Figure 17. Rear Shroud Removal
5. Disconnect the battery tie-down strap that holds the batteries in place.
6. Unplug both black and white 2-pin battery harnesses. See figure 18.
7. Unplug the front-to-rear harness from its mating plug. See figure 19.
Figure 18. Disconnecting The Battery Harnesses
32
www.pridemobility.com Maxima
Figure 19. Disconnecting The Front-To-Rear Harness
I X . DISASSEMBLY AND ASSEMBLY
NOTE: There is no need to disconnect the motor harness when disassembling the scooter. See figure 20.
8. Lift both batteries off the scooter. See figure 21.
MOTOR
HARNESS
Figure 20. Motor Harness
WARNING! Failure to unplug both battery har nesses and the front-to-rear harness prior
to frame separation could result in permanent damage to the scooter.
Figure 21. Battery Removal
9. Push the locking cam levers forward to the unlocked position and remove the ball detent pins. See
figures 22 and 23.
Figure 22. Locking Cam Levers (Unlocked Positon)
Figure 23. Frame Lock-up Ball Detent Pins
10. Remove the frame handle ball detent pin. See figure 24.
11. Gently slide the two sections of the scooter apart. See figure 25.
12. Grab the handle grip on the tiller, pull upward on the tiller adjustment lever, and fully lower the tiller
down to the center of the scooter chassis.
Maxima www.pridemobility.com
è
Figure 25. Frame SeparationFigure 24. Frame Handle Ball Detent Pin
33
I X . DISASSEMBLY AND ASSEMBLY
ASSEMBLY
NOTE: Raise the tiller before starting to reassemble the scooter.
1. Place the manual freewheel lever in the drive (down) position.
2. Position the front and rear sections next to each other.
3. Tilt the rear end to a horizontal position and insert the longer tube of the front end into the rear section
first; make sure that the locking cam levers are in the unlocked (forward) position and the ball detent
pins are removed.
4. Slide the two sections of the unit together until the front half reaches its insertion limit.
5. Secure the front and rear sections with the ball detent pins.
6. Push the frame lock levers back to their locked (upward) position.
7. Replace frame handle ball detent pin.
8. Plug the front-to-rear harness into its mating plug.
9. Put the batteries in place and plug both black and white 2-pin battery harnesses into their mating plugs.
10. Reconnect the battery tie-down strap.
11. Reinstall the rear shroud.
12. Reinstall the seat.
13. Rotate the seat until it locks into place.
34
www.pridemobility.com Maxima
X. BASIC TROUBLESHOOTING
Any electromechanical device occasionally requires some troubleshooting. However, most of the problems
that may arise can usually be solved with a bit of thought and common sense. Many of these problems
occur because the batteries are not fully charged or because the batteries are worn down and can no longer
hold a charge.
DIAGNOSTIC FLASH CODES
The diagnostic flash codes for your scooter are designed to help you perform basic troubleshooting quickly
and easily. A diagnostic flash code flashes from the status LED in the event one of the conditions listed
below develops.
NOTE: Your scooter will not run unless the flash code condition is resolved and the scooter has been
turned off then turned back on.
FLASH CODE CONDITION SOLUTION
n n n n n
n n
n n n n
n n n n n
n n n n n n
Batteries are too low to operate th e
Maxima or the charger is operating.
Contr o ller is hot ; the Max i ma seems
to be losing power.
Wigwag fa ult; yo ur th r o ttle cont r ol
levers are not responding.
The man u al freew h eel lever is in th e
(up) freewheel position.
The Maxima is operating with the
charg er attached.
Charge batteries or unplug the charg er power
cord fro m th e el ectrical outl et .
Shut down your Maxima for several minutes
to allow the cont r o ller to cool.
Call your authorized Pride Provider for
assistance.
Turn the Maxima key to the off position,
then push the manual freewheel lever to the
(down) drive position , restart your Max im a.
Unplug the charger cord from the charger
power co r d r eceptacle.
What if all the systems on my scooter seem to be dead?
n Make certain that the key is in the on position.
n Check that the batteries are fully charged. See VI. Batteries and Charging.
n Push in the main circuit breaker reset button. See V. Your Scooter
n Make certain that both battery harnesses are firmly connected to the electronics module and to the
battery terminals. See IX. Disassembly and Assembly.
n Make sure that the front-to-rear harness is firmly connected to the electronics module. See IX.
Disassembly and Assembly.
n Check the fuses. See XI. Care and Maintenance for fuse replacement.
n Be sure the power down timer feature hasnt been activated. See VII Operation.
What if the motor runs but my scooter does not move?
n With the key turned to the on position, check the status LED. If the LED flashes three times, pauses
briefly, then flashes two times, this is the manual freewheel lever code meaning your scooter is in
freewheel mode.
n When the manual freewheel lever is pulled up, the brakes are disengaged and all power to the transaxle
is cut.
n Push down the manual freewheel lever to restore normal operation to your scooter See V. Your Scooter.
Maxima www.pridemobility.com
35
X. BASIC TROUBLESHOOTING
What if the main circuit breaker repeatedly trips?
n Charge the scooters batteries more frequently. See VI. Batteries and Charging.
n If the problem continues, have both of your scooters batteries load tested by your authorized Pride
Provider.
n You may also perform the load test yourself. Battery load testers are available at most automotive parts
stores.
n Follow the directions supplied with the load tester.
n See VI. Batteries and Charging or IV. Specifications for information about your scooters battery type.
What if the battery condition meter dips way down and the motor surges or hesitates when I press
my scooters throttle control lever?
n Fully charge your scooters batteries. See VI. Batteries and Charging.
n Have your authorized Pride Provider load test each battery.
n Or, see the previous troubleshooting question for load testing the batteries yourself.
If you experience any problems with your scooter that you are not able to solve, immediately contact your
authorized Pride Provider for information, maintenance, and service.
36
www.pridemobility.com Maxima
XI. CARE AND MAINTENANCE
Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your
ability to perform the maintenance listed below, you may schedule inspection and maintenance at your
authorized Pride Provider. The following areas require periodic inspection and/or care and maintenance.
TIRE PRESSURE
n If equipped with pneumatic tires, always maintain a proper 30-35 psi tire pressure.
WARNING! It is important that 30-35 psi tire pressure be maintained in pneumatic tires at
all times. Do not underinflate or overinflate your tires. Low pressure may result in loss of
control, and overinflated tires may burst. Failure to maintain 30-35 psi tire pressure in
pneumatic tires at all times may result in tire and/or wheel failure, causing serious personal
injury and/or damage to your scooter.
n Regularly inspect your scooters tires for signs of wear.
EXTERIOR SURFACES
Bumpers, tires, and trim can benefit from an occasional application of rubber or vinyl conditioner.
WARNING! Do not use a rubber or vinyl conditioner on the scooters vinyl seat, floorboard,
or tire tread. They will become dangerously slippery and result in personal injury and/or
damage to your scooter.
BATTERY TERMINAL CONNECTIONS
n Make certain that the terminal connections remain tight and uncorroded.
n The batteries must sit flat in the battery wells.
n The battery terminals should face the rear of the scooter.
WIRING HARNESSES
n Regularly check all wiring connections.
n Regularly check all wiring insulation, including the charger power cord, for wear or damage.
n Have your authorized Pride Provider repair or replace any damaged connector, connection, or insula-
tion that you find before using your scooter again.
ABS PLASTIC SHROUDS
n The front tiller shroud, front shroud, and the rear shroud are formed from durable ABS plastic and are
coated with an advanced formula urethane paint.
n A light application of car wax will help the shrouds retain their high gloss.
AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY
These items are all prelubricated, sealed, and require no subsequent lubrication.
MOTOR BRUSHES
The motor brushes are housed inside of the motor transaxle/assembly. They should be inspected periodically for wear by your authorized Pride Provider.
Maxima www.pridemobility.com
37
XI. CARE AND MAINTENANCE
CONSOLE, CHARGER, AND REAR ELECTRONICS
n Keep these areas free of moisture.
n Allow these areas to dry thoroughly if they have been exposed to moisture before operating your scooter
again.
FUSE REPLACEMENT
In the event a fuse should cease to work:
n Remove the fuse by pulling it out of its slot.
n Examine the fuse to be sure it is blown. See figures 26 and 27.
n Insert a new fuse of the proper rating.
Figure 26. Working Fuse Figure 27. Blown Fuse (Replace)
WARNING! The replacement fuse must exactly match the rating of the new fuse. Failure
to use properl y rated fuses may cause damage to the electrical system and may result in
personal injury.
LIGHT BULB REPLACEMENT
The scooters light bulbs are easily replaceable. Do not use regular automotive-type 12-volt light bulbs;
your scooter is equipped with a 24-volt electrical system. Replacement light bulbs can be purchased from
your authorized Pride Provider.
NOTE: Use only 24 volt light bulbs.
n Remove the light cover.
n Gently remove the bulb by pulling it straight out.
n Insert a new bulb of the same wattage.
n Replace the light cover.
STORING YOUR SCOOTER
If you plan on not using your scooter for an extended period of time, it is best to:
n Fully charge its batteries prior to storage.
n Disconnect the batteries from the scooter.
n Store your scooter in a warm, dry environment.
n Avoid storing your scooter where it will be exposed to temperature extremes.
WARNING! Always protect batteries from freezing temperatures and never charge a frozen
battery. This damages the battery and can cause personal injur y.
For prolonged storage, you may wish to place several boards under the frame of your scooter to raise it off
of the ground. This takes the weight off the tires and reduces the possibility of flat spots developing on the
areas of the tires contacting the ground.
38
www.pridemobility.com Maxima
XII. WARRANTY
THREE-YEAR LIMITED WARRANTY
Three years on all structural frame components; including platform, fork, seat post, and frame.
Three-year prorata drive train warranty; including transaxle, motor, and brake.
n First year: 100% replacement of parts cost
n Second year: 67% replacement of parts cost
n Third year: 50% replacement of parts cost
THREE-YEAR WARRANTY EXCEPTIONS
Transaxle: In cases where there is an increase in the operational noise level, the warranty does not apply.
(The increase in operational noise level usually occurs due to abusive and excessive strain on the scooter.)
Motor brake: Three-year warranty for the electrical function of the motor brake. Brake pads are a wear
item and are not warranted.
ONE-YEAR LIMITED WARRANTY
For one (1) year from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of charge, any part or electronic component found upon examination by an authorized representative of Pride to be defective in material and/or workmanship.
The battery is warranted by the battery manufacturer. The battery is not warranted by Pride.
Warranty service can be performed by Pride or by an authorized Pride Provider. Do not return faulty parts
to Pride without prior consent. All transportation costs and shipping damage incurred while submitting
parts for repair or replacement are the responsibility of the original purchaser.
WARRANTY EXCLUSIONS
n ABS plastic shrouds and footrest covers (wear items and not warranted)
n Batteries (the battery manufacturer provides a limited warranty)
n Tires and tire tubes (wear items and not warranted)
n Upholstery and seating (wear items and not warranted)
n Repairs and/or modifications made to any part of the scooter without specific and prior consent from Pride
n Circumstances beyond the control of Pride
n Damage caused by: battery fluid spillage or leakage, abuse, misuse, accident, or negligence, improper
operation, maintenance, or storage, commercial use or use other than normal
n Labor, service calls, shipping, and other charges incurred for repair of the product
There is no other express warranty.
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to
one (1) year from the date of original purchase and to the extent permitted by law. Any and all implied
warranties are excluded. This is the exclusive remedy. Liabilities for consequential damages under any and
all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of
limitation of incidental or consequential damages. So, the above limitation or exclusion may not apply to you.
Maxima www.pridemobility.com
39
NOTES
40
www.pridemobility.com Maxima
182 Susquehanna Ave.
Exeter, PA 18643
1-800-800-8586
www.pridemobility.com
Loading...