Page 1
Features
Δ 3-Axis Plastic Dome Camera
Δ Advanced H.264 High profile compression
Δ Support browsers: IE
Δ Support several servers, IP address, DDNS, FTP,SMTP
Δ Support single, dual, three streams
Δ Support iPhone, iPad, Android remote monitor
Δ Support connect to NVR
Δ Support ONVIF2.0
Δ Reliability and compatibility
Δ Low streams and high resolution image
Connection
Network Structure
switch/router/FOT
IPC
PC1
PC2
RJ45
DC12V
DKW3100T
IPC Fast Operation
User Manual
Please refer to the complete User manual
for more information from the CD.
HD-IP CAMERA
Specifications
Model DKW3100T
Image Sensor 1/4" Omnivision 1 Megapixel CMOS Sensor
Resolution 1280x720
Minimum
Illumination
>1Lux
S/N Ratio >50db
Focus Mode Manual Focus
Day/Night IR cut filter with auto switch, IR sensor.
Network
1 RJ45 Ethernet interface, 10/100M
adaptation
Delay Within The LAN 0.3S
Frame Rate 25 FPS (adjustable)
Video
Compression
H.264 /JPEG
Protocol RTSP/FTP/DDNS/NTP/SMTP
Onvif Support Onvif 2.0
User Permission Multi-user Classification Management
Consumption 3.0W
Power/Current
DC 12V/1A or POE
Lens
2 Megapixel HD
2.8-12mm Manual Zoom Lens
IR Status
IR LED: ￠5X21PCS
IR range: 20M
Dimension (mm)
￠135 x 100(H) mm
Weight (g) 650
Temperature
-10～55℃
Humidity 0%-90%RH,Without Condensation
POE Yes(optional)
NO. Name Number (pcs)
1. HD-IP Camera 1
2. CD 1
3.
IPC Fast
Operation
User Manual
1
Model
DKW3100T
DKW3100T
DKW3100T
Access to the IP
Camera via IE
1. Use correct power supply.
2. Make sure the device IP address
is in the same LAN with the
router, the default IP a ddress of
the IPC is 192.168.1.168.
3. Go to C D->IPCSearch.exe and
copy it to your computer.
4. Open IPC Search, click “Search”,
you will find the device IP, and
you also can modify the IP
information, see the picture (1)
5. Factory default IP setting:
IP Address : 192.168.1.168
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
User name: admin
Password: admin
6. After modifying IP, click “Search”
again, you will find the new IP of
the your device. Double-click the
new IP, you can access to the IPC
via IE, or enter the IP Address in
the address bar of IE, then click
“Enter”, the download_OCX
controls interface please see the
picture (2), Please click here
to download the OCX
controls.
7. as is shown in picture (3), Click
run, the system will automatically
download the OCX.
8. Click “yes” as the picture (4),Then
it will install the OCX，when
complete ,Click ”OK” and refresh
the page. You will enter the login
interface, as is shown in picture
(5)
9. Enter your username and
password, you can start to access
and control your IP Camera.
Access to the IP
Camera via
Multi_window
Go to CD, find “Multi_window.exe.
“ Copy “Multi_window.exe “ to your
computer and install it, then run it.
See the picture (6):
1
. Config: Group. See the picture
(7):
Here you can add your IP
Cameras and set the Capture
Path. If you forget the IP Address,
（1）
（2）
（3）
（4）
（5）
（6）
（7）
You can select “List all ipcam” or
“List only unselect”, then double
click the IP info to add the
camera. You also can enter the
IP Info manually in the “IPcam
Information area”. Then you can
view the images and set the
parameters of IP Camera, such
as Alarm, Video, Net, Camuser,
Date, etc. Please refer to Multi_
window Customer Manual for
detail.
2. View the images
After adding the devices, you
can see the devices in “List” of
the main interface, you can
double _click the device to
control it to play or stop. See
the picture (8):
You also can control the devices
in “Camera”,
see the picture (9) on the right:
Access to the IP Camera
via Android mobile
Search and download the
surveillance software “Danale” to
your mobile from electronic
markets or the Mobile Assistant,
then install it. Then you can see
the icon of the software
,click it to run.
1. Login
The picture (10) shows the login
interface:
2. List
As is shown in picture (11)
2.1 Add Camera
Click “add camera”, as is shown
in picture (12):
Edit the camera name, input the
username, password, you can
input the camera ID manually or
scan the QR code directly. Click
“finish” to finish and save it.
3. Video Mode
Click to set the Video
Mode.
4.Settings
Click to set the IPC. As is
shown in picture (13):
4.1 User name password
management
Here you can edit the device
name, username and password.
4.2 NetWork Settings
Here you can set the local
network and WIFI according to
your need.
4.3 Basic information
Here you can view the basic
information of the IPC, including
device information, storage
information, etc.
(8)
(9)
(10)
(11)
(12)
(13)
Page 2
4.4 Parameter settings
Here you can set some parameters of the IPC, including Video
quality, Time setting, Mail settings, Frequency setting, Chroma
Setting, and Visu Alangle Settings
4.5 Alarm settings
Here you can set alarms, including Motion Detect, Audio Alarm, I/
O Alarm, Privacy Covered alarm, Timing to capture, Timing to
record.
4.6 Init settings
Here you can Restore Factory Set and Restart the system of IPC.
4.7 Live View
When playing the video,
you can capture, record,
open/close the audio or
mic; If the IPC supports
PTZ, you can slide up,
down, left and right on
the screen. As shown in
figure (14).
5. Images View
Click “Images
View” to playback pictures.
6. Video View
Click “Video View” to playback records.
7. About
Here you can view the information of the monitor software.
Access to the IP Camera via iPhone
Search and install the surveillance software “Danale” on line to your
mobile from App store. Then you can see the icon of the software
click it to run.
1. Login
Input username and password, click
“Login” in the login interface, you will
enter the “List” interface.
2 List
As is shown in figure(15):
2.1 Add Camera
Click to add camera, you will see
the picture on the right:
Edit the camera name, input the
username, password, you can input the
camera SN manually or scan the QR
code directly.
3. Video Mode
Click “VideoMode”on the top right to
set the mode of the video, Including
high definition, standard definition and
Automatically.
4. Settings
Click to set the IPC. See the picture
(16) on the right:
4.1 User name password management
Here you can edit the device name,
username and password
4.2 Basic information
Here you can view the basic information of the IPC, including
4.3 NetWork Settings
Here you can set the local network and
WIFI according to your need.
4.4 Parameter settings
Here you can set some parameters of
the IPC, Including Video quality, Time
setting, Mail settings, Frequency setting,
Chroma Setting, and Visu Alangle
Settings
4.5 Alarm settings
Here you can set alarms, including
Motion Detect, Audio Alarm, I/O Alarm,
Privacy Covered alarm, Timing to
capture, Timing to record.
4.6 Init settings
Here you can Restore Factory Settings
and Restart the system of IPC.
5. Live View
When playing the video, you can
capture, record, open/close the audio or mic; If the IPC supports
PTZ, you can slide up, down, left and right on the screen. As is
shown in the following picture:
6. Images View
Click “Image” to playback pictures.
7. Video View
Click “Video” to playback records.
8. About
Here you can view the information of the monitor
software.
Access to the IP Camera via iPad
Search and download the surveillance software
“Danale HD” to your iPad from App store and install
it. Then you can see the icon of the software
,click it to run.
1. Login
Input username and password, click “Login” in the
login interface, you will enter the “List” interface.
2. List
As is shown in figure on the right:
2.1 Add Camera
Click to add camera, you will see the following picture:
Edit the camera name, input the username, password, you can
4.1 User name password
management
Here you can edit the device
name, username and password.
4.2 Basic information
Here you can view the basic
information of the IPC, including
device information, storage
information, etc.
4.3 NetWork Settings
Here you can set the local
network and WIFI according to
your need.
4.4 Parameter settings
Here you can set some
parameters of the IPC, including
Video quality, Time setting, Mail
settings, Frequency setting, Chroma Setting, and Visu Alangle
Settings
4.5 Alarm settings
Here you can set alarms, including Motion Detect, Audio Alarm, I/
O Alarm, Privacy Covered alarm, Timing to capture, Timing to
record.
4.6 Init settings
Here you can Restore Factory
Settings and Restart the
system of IPC.
5. Live View
When playing the video, you
can capture, record, open/
close the audio or mic; If the
IPC supports PTZ, you can
slide up, down, left and right
on the screen. As is shown in the right picture:
6. Images View
Click “Image” to playback pictures.
7. Video View
Click “Video” to playback records.
8. About
Here you can view the information of the monitor software.
FAQ
1.Why cannot capture?
If you capture failed and the storage folder cannot pop up
automatically ,please check your IE, don’t select “Enable protected
mode”.
2.Why can not access the camera after update?
Clean browser cache.
Steps: open IE, click “Tools” and select “Internet Options”, then you
can see “Temporary Internet files” and click “Delete Files”, it will
prompt a dialog you need to check
“Delete all offline content”
3. Why can not show the whole interface?
Close some options of IE.
Steps: Open IE, click ”View” and select “Toolbar”, close the
“Favorites bar”, ”Status bar” and “Command bar”.
4. Why cannot I watch the mobile surveillance video after entering
the login information?
A、Please check whether the settings page, server, port, user name,
password and other information are filled in correctly.
B、Please check your network to see whether your phone is
connected to the external network .
C、If your device is connected to the external network via router,
please check whether the mobile port mapped in the routing .
(For mapping settings, please refer to the router manual).
D、Please check whether the IP address you have filled in is the LAN
IP (If your IP starts with the following format, it is a local area
network : 10.xx 、172.xx、192.xx. If you use such IP, you can
only be in the same LAN with the device to be connected).
E、Please check your port to ensure that it must be the mobile port.
5. Why does it show “Get Param Failed”?
1.Please check the IP information, such as port.
2.Please make sure the IP Camera connected correctly.
3.The network status is poor.
6. I have already added the device, why it shows “Initial Failed!”?
Solution: Please delete the device and add it again.
The Important Safety Information
Please be sure to read the following important safety information
before install and use the product.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC DO NOT REMOVE COVER OR
BACK NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
OUALIFIED SERVICE PERSONNEL.
CAUTION:
TO PREVENT ELECTRIC SHOCKS AND RISK OF FIRE HAZARDS, DO
NOT USE OTHER THAN SPECIFIED POWER
SOURCE.
CAUTION:
RISK OF ELECTRIC. DO NOT
OPEN
Notes：
●The power supply must through safe attestation. Its output
voltage, current, voltage polarity and operating temperature
must match the camera’s requirement.
●When using the camera in the thunderbolt condition,please
note to mount Anti-thunder device or put off the power supply
plug and cable.
●In order to capture high quality pictures, the power supply’s
cable and video output cable should not be too long.
(14)
(17)
(18)
(15)
(16)
Loading...