Presto ShineOn Electric Shoe Polisher Instruction Manual

O
N
O
F
F
R
E
L
ShineOn Electric
Shoe Polisher
• Shines men’s, women’s, and children’s shoes like a professional.
• Quickly polishes and buffs for a perfect shine, every time.
• A complete shoe care kit including power handle, two polish applicators, two polishing brushes, two buffing pads, and storage tray.
2006 by National Presto Industries, Inc.
This is a Listed appliance. The following important safeguards are recommended by most portable appliance manufacturers.
Visit us on the web at www.GoPresto.com
IMPORTANT SAFEGUARDS
WARNING:
precautions should always be followed, including the following:
1. Read all instructions before using the appliance.
2. To protect against the risk of electrical shock, do not immerse or operate electric shoe polisher in water or under running
water or other liquids. Do not place or store electric shoe polisher where it can fall or be pulled into a tub or sink.
3. Close supervision is necessary when any appliance is used by or near children.
4. To disconnect, turn all controls to OFF position, then remove plug from wall outlet.
5. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Unplug from outlet when not in use, when changing brushes, and before cleaning.
6.
7. Avoid contact with moving parts.
8. Do not operate any appliance with a damaged cord or plug or in the event the appliance malfunctions or has been damaged
in any manner. Return the appliance to the Presto Factory Service Department or to the nearest Presto Authorized Service Station for examination, repair, or electrical or mechanical adjustment.
9. The use of accessory attachments not recommended by the appliance manufacturer may cause fire, electric shock, or
injury.
10. Do not use outdoors.
11. Do not use shoe polisher for other than intended use.
To reduce the risk of personal injury or property damage, when using electrical appliances basic safety
SAVE THESE INSTRUCTIONS
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
POLARIZED PLUG – Connect the power supply cord to a polarized outlet only. As a safety feature, this appliance has
a polarized plug (one blade is wider than the other). This plug will only fit in a polarized outlet one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
1
O
N
O
F
F
R
E
L
O N
O F
F
R E
L
Before Use
• Become familiar with the various parts of the shoe polisher (FIG. A) and read the instructions carefully.
Polish applicators, brushes, and buffing pads are color-coded brown and black for use with different polish colors.
Note: Your shoe polisher will be shipped with one of the buffing pads attached to one of the brushes. Before you begin
polishing, remove the buffing pad from the brush by turning the pad counterclockwise. Set the buffing pad aside for later use.
• It is a good idea to wear an apron or smock, to protect clothing during polishing.
• Be sure to protect the area in which polishing is being done, to avoid polish stains. Choose a location away from carpet and furniture.
How To Use
1. Using one of the two color-coded polish applicators (Fig.
A) found in the storage tray, apply a very thin even coat of polish to the outer surface of the footwear to be polished. When completed, return the applicator to the appropriate receptacle in the storage tray.
2. Attach the appropriate color-coded brush to the power
Power/Brush
Release Switch
Brushes
Buffing Pads
Power
Handle
handle by inserting the shaft portion of the brush into the receptacle in the power handle (Fig. B). It may be neces­sary to turn the brush slightly to the right or left until the
Polish Applicators
brush clicks into place.
To remove the brush
, slide the power/brush release switch
Fig. A
Storage Tray
(Fig. B) to the release (REL) position. While holding the switch in this position, remove the brush.
3. Plug cord into outlet and slide the power/brush release switch (Fig. B) forward to the
ON position.
4. Move the brush slowly over the entire shoe surface with a light steady pressure, mak
Receptacle
Shaft
Power Handle
-
Fig. B
Power/Brush
Release Switch
ing sure the brush gets into all contours of the shoe. When finished, slide the power switch to the OFF position.
5. Place the appropriate color-coded buffing pad over the polishing brush, aligning the
grooves on the pad with the tabs on the brush (Fig. C). Lock it in place by turning the buffing pad clockwise. Slide the power/brush release switch forward to the ON posi­tion and move the buffing pad slowly over the entire shoe surface with a light steady pressure.
Tab
Fig. C
Groove
Helpful Hint: For a dazzling shine, spray a light mist of water on the shoes prior to buff-
ing.
6. When finished, slide the power switch to the
OFF position and unplug power cord from
outlet.
7. Remove the buffing pad by turning it counterclockwise; place the buffing pad back in the
storage tray. To remove the brush, slide the power/brush release switch (Fig. B) to the release (REL) position. While holding the switch in this position, remove the brush.
Storage: When not in use, place the power handle with the brush attached into the storage tray. The recessed area in the bot­tom of the power handle fits over the shaft of the other brush and holds the power handle in position for storage.
2
Loading...
+ 1 hidden pages