Prestigio P260MW, P260DVD-X, P320MW, P320DVD-X User Manual

1PRESTIGIO P260MW / P260DVD-X - PRESTIGIO P320MW / P320DVD-X

ENG

Prestigio P260MW / P260DVD-X
Prestigio P320MW / P320DVD-X

User’s Manual

Before using this product, please read the security instructions first and bear them in mind when using the product.

2 PRESTIGIO P260MW / P260DVD-X - PRESTIGIO P320MW / P320DVD-X

ENG

Safety Instruction

Warning

TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED. DANGEROUS VOLTAGE.
WITHIN THE PRODUCTS ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF
ELECTRIC SHOCK TO PERSONS.

THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND
MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.

Important Safety Instructions

This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must
be taken if you are to obtain the best results and safety is to be assured. So, please read the points below for your own safety. They are
of a general nature, intended to help you with all your electronic consumer products and some points may not apply to the goods you have
just purchased.

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with a dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

• This TV is not completely disconnected from a power supply line, as minute current is consumed even when the POWER switch is turned
off.

• Do not place hot objects or naked flame sources, such as lighted candles or nighlights on, or close to the TV. High temperatures can melt
plastic and lead to fires.

• Do not set on top of the TV any object or container that might spill liquids or small objects into the TV.

• Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits the
apparatus.

• Only use attachments/accessories specified by the manufacturer.

• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.

• The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

3PRESTIGIO P260MW / P260DVD-X - PRESTIGIO P320MW / P320DVD-X

ENG

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type.

Overview

Front View

1 MASTER SWITCH
2 Remote Control Sensor
3 POWER: Turns the TV on and off.
4 LED Lights
5 VOLUME: Increases or decreases the volume. This is also used to select the “MOVE&ADJUST” item on the on-screen menu.
6 PROGRAM: Changes channels or “MOVE&ADJUST” to items on the on-screen menu.
7 MENU: To access or close menus, simultaneously.
8 TV/VIDEO: Selects an external device connected to the TV.

<DVD> - Depend on the model

9 PLAY/PAUSE: Play the DVD or temporarily stop playback.
10 STOP: Stop the DVD playback.
11 OPEN/CLOSE: OPEN/CLOSE the DVD.
12 ON/DISC LED

Rear Panel Jacks

1 PC INPUT (VIDEO/AUDIO) JACKS
2 DVI INPUT (VIDEO/AUDIO : L/R) JACKS : DVI-D Only (Depend on the
model)
3 COMPONENT JACKS (VIDEO : Y, Pb, Pr/AUDIO : L/R)
4 LINE (VIDEO/AUDIO) OUTPUT JACKS
5 VIDEO3 (VIDEO/AUDIO) INPUT JACKS
6 S-VIDEO INPUT JACK
7 DIGITAL AUDIO OUTPUT JACK (Depend on the model)
8 SCART JACKS (BOTTOM : SCART1, TOP : SCART2)
9 HEADPHONE JACK. Used for headphones that can be purchased
additionally.
10 TV ANTENNA INPUT JACK

4 PRESTIGIO P260MW / P260DVD-X - PRESTIGIO P320MW / P320DVD-X

ENG

Remote Control

1 LINE: External input selection. (TV > RGB > Video1 > Video2 > Video3
> S-Video > Component > DVI (Option) > PC)
2 POWER: Turns the TV on and off.
3 TV: Switches to TV mode.
4 SWAP: Exchanges the video signal source of the main screen and the PIP
window.
5 ON/OFF: Turns PIP on or off.
6 NUMBER BUTTONS: Selects channels directly on the TV.
7 -/—: Selects channels over 10. For example, to select channel 21, press
“-/—” then press “2”, “1”.
8 STILL: Freezes a moving picture on the screen.
9 M/S: Sound mode selection.
10 P.STD: Configures various video settings.
11 ARROW/ENTER: Select an item of menu/Change confirmation.
12 P.SIZE: Changes the screen size.
13 DISPLAY: Displays the current channel and the audio video settings.
14 MUTE: Temporarily mute the sound.
15 TTX: Switches to Teletext mode.
16 SOURCE: Selects the signal source for the PIP window.
17 SOUND: Changes the audio signal source between the main screen and
the PIP window.
18 VOL: Increases or decreases the volume.
19 PRE: Moves to the previous channel.
20 PROG: Changes channels.
21 SLEEP: Selects a preset time interval for automatic shutoff.
22 TV.MENU: Displays the OSD menu.
23 S.STD: Configures various audio settings.
24 EXIT/CANCEL: Exit the current configuration or the teletext display.

<DVD> - Depend on the model

25 DVD: Displays the DVD.
26 OPEN/CLOSE: OPEN/CLOSE the DVD tray.
27 SCAN/SLOW: For fast and slow playback.
28 TITLE: For selecting a title on the disc.

29 SETUP: For initial DVD player settings.
30 STOP: Stop the DVD playback.
31 PLAY/PAUSE: Play the DVD or temporarily stop playback.
32 SKIP/STEP: For skipping to the next chapter/For playing one frame at a time.
33 MENU: For displaying the menu contained in the disc.

<DVD & TTX> - Depend on the model

34 COLOR KEY: Fasttext topic selection.
35 INDEX/REPEAT: Programme selection by name/ For specifying and repeating playback of a segment.
36 MIX/A-B: Video & TTX MIX/For repeated playback of disc titles, chapters or sound.
37 HOLD/PROGRAM: Teletext page/For playback in a specified order.
38 PRE PAGE/ANGLE: Teletext previous page/ For viewing scenes from different.
39 L/F/AUDIO: Switching the LIST or FLOF mode./ For selecting the audio language.
40 REVEAL/GOTO: Teletext reveal/For jumping to a specified location.
41 SIZE/SUBTITLE: Teletext size selection/For selecting the SUBTITLE language.
42 STORE/CLEAR: To store the teletext in the LIST mode/To erase a program content.
43 SUB PAGE/ZOOM: Teletext SUB-PAGE/For magnifying the screen.
44 NEXT PAGE/SURROUND: Teletext NEXTPAGE/For stereophonic sound effect.

5PRESTIGIO P260MW / P260DVD-X - PRESTIGIO P320MW / P320DVD-X

ENG

Connecting Your TV

Connecting an Antenna or Cable without a Decoder box

Connecting the Scart Jack

Connection Procedures

1 SCART1 is used for the equipment with an RGB output, such
as video game devices or video disc players. This end can be
fitted with:

- A SCART connector

- Three RCA connectors(VIDEO+AUDIO_L+AUDIO_R)

Procedures for watching a Video over a VCR

1 Turn the TV on, and select ‘VIDEO1’ using the LINE button on
the remote control.
2 If you have a second VCR and wish to copy cassette tape,
connect the source VCR to SCART1 and the target VCR to
SCART2 so that you can redirect the signal from SCART1 to
SCART2.

Connecting a Digital Audio System (Depend on the model)

Connection Procedures

1 Connect the DIGITAL OUT (black) jack on the back of your
TV to the DIGITAL IN jack of the Decoder or AV amplifier.

To use the digital out

1 Turn the TV on, and select ‘DVD’ using the DVD button on the
remote control.
2 Turn the digital amp on and select the external input mode.

6 PRESTIGIO P260MW / P260DVD-X - PRESTIGIO P320MW / P320DVD-X

ENG

Connecting the Video or S-Video/Audio Jacks

Connection Procedures

1 Connect the antenna cable to the ANTENNA IN terminal on
the back of your VCR.
2 Connect the VIDEO/AUDIO INPUT jacks of the TV and the
video/audio output jacks of your VCR with the video/audio
cables. (Connect the cable to the terminal of the same color)

- You can use the S-Video cable to connect a VCR or a DVD
player for better video quality.

- If your VCR does not support stereo sound, connect the
mono audio out jack to the AUDIO INPUT (left) jack.

Procedures for watching a video over a VCR

Turn the TV on, and select ‘VIDEO 3’ using the LINE button on the remote control.

- If you have connected a S-Video cable, select ‘S-VIDEO’.

Connecting a External TV

Connection Procedures

1 Connect the AUDIO CABLES between the AUDIO OUT L and
R jacks on the back of your TV and the corresponding AUDIO
INPUT jacks on external TV.
2 Connect the VIDEO CABLE between the VIDEO OUT jack on
the back of your TV and the corresponding VIDEO INPUT jack
on external TV.

To watch the external TV

1 Turn the external TV on and select ‘VIDEO’ using the
external input button.
2 Turn the your TV on.

Connecting the DTV Receiver

Connection Procedures

1 The COMPONENT VIDEO IN and COMPONENT AUDIO IN
connectors are used for equipment with a DVD or DTV re­ceiver out. (480i/60Hz, 480p/60Hz, 576i/50Hz, 576p/50Hz,
720p/50Hz, 720p/60Hz, 1080i/50Hz,1080i/60Hz)

To watch the DTV

1 Turn the TV on, and select ‘COMPONENT’ using the LINE
button on the remote control.
2 Turn the DTV Receiver on.

Connecting the DVI JACK (DVI-D

7PRESTIGIO P260MW / P260DVD-X - PRESTIGIO P320MW / P320DVD-X

ENG

Only: Depend on the model)

Connection Procedures

1 Connect the DVI input jack of the TV and the DVI output jack
of your DTV Receiver.
2 Connect the DVI audio input jacks of the TV and the DVI
audio output jacks of your DTV Receiver with the audio cable.

Check Before Using

Please check the following check list before using the TV.
1 Is the antenna cable connected properly?
2 Are the remote control batteries installed properly?

- Install two AAA size batteries according to the correct polarity.

- The remote control works up to about 7~10m from the TV, 3m to the left or right of the TV, and to within 30 degrees from
the remote control sensor of the TV.
3 Have the receive channels been configured?
4 Are the cables connected to any external devices connected properly?

TV Function

Watching TV

Turning the TV On and OFF

1 Plug the mains lead into an appropriate socket.
2 Press the POWER switch on the bottom of the television toward “ON”(I).
3 Press the POWER button on the remote control (or on the front panel of the unit.)
You can also switch on by pressing the PROG \/ /\ buttons.

• When you turn the power ON, the screen appears and the POWER/STANDBY light is turned off.

• When you turn the power OFF, the screen goes blank, and the POWER/STANDBY light turns red.

• Do not leave your television in Standby mode for long periods of time (when you are away on holiday, for example). Turn
your television off by pressing the POWER switch toward “OFF”(O). It is best to unplug the set from the mains and aerial.

Selecting the Menu Language

1 Press the TV.MENU button. The OSD MENU will be displayed.
2 Select FUNCTION using the /\ \/ button and then press the > button.
3 LANGUAGE using the /\ \/ button and then press the > button.
4 Select the desired menu language using the /\ \/ button.
5 Press the EXIT/CANCEL button to exit the menu.

8 PRESTIGIO P260MW / P260DVD-X - PRESTIGIO P320MW / P320DVD-X

ENG

Viewing the Status Information

Press the DISPLAY button on the remote control. The TV will display the input source, the picture mode, the sound mode, the
STEREO mode, the sleep time, the current time, and the pip mode.

Adjusting the Volume

Adjust the volume using the VOL /\ \/ button.

Muting the Sound

Press the MUTE button. You can conveniently use the MUTE button when a telephone or a door bell rings. To cancel, press the
MUTE button again.

Viewing a Video, DVD or COMPONENT

Press the LINE button.

Storing Channels Automatically

1 Press the TV.MENU button. The OSD MENU will be displayed.
2 Select SETUP using the /\ \/ button and then press the > button.
3 Select AUTO PROGRAMMING using the /\ \/ button and then press the >
button.
4 Select COUNTRY using the /\ \/ button and then press the > button.
5 Select your COUNTRY using the /\ \/ button and then press the > button. The
countries are displayed in the following order.
6 Select SEARCH using the /\ \/ button and then press the > button.

Manual Storing of Channels

When storing channels manually, you can choose:

- Whether or not to store each of the channels found.

- The programme number by which you wish to identify each stored channel.
1 Press the TV.MENU button. The OSD MENU will be displayed.
2 Select SETUP using the \/ /\ button and then press the > button.
3 Select MANUAL PROGRAM using the \/ /\ button and then press the >
button.
4 Select SYSTEM using the \/ /\ button and then press the > button.
AUTO > BG > DK > I > L > LP > AUTO
5 Select PROGRAM NO. using the \/ /\ button and then press the > button. And
press the \/ /\ button to select the required channel number.
6 Select SEARCH using the \/ /\ button and then press the > button.
The tune scans the frequency range until the first channel on the channel that you selected is received on your screen.
7 Select STORE using the \/ /\ button and then press the > button. And press the \/ /\ button to select the OK.
8 Repeat Step 5 to 7 for each channel to be stored.

9PRESTIGIO P260MW / P260DVD-X - PRESTIGIO P320MW / P320DVD-X

ENG

Channel Name

1 Press the TV.MENU button. The OSD MENU will be displayed.
2 Select SETUP using the /\ \/ button and then press the > button.
3 Select NAME using the /\ \/ button and then press the > button. And press
the /\ \/ < > buttons to edit the name.
/\ \/: Select the characters (A~ Z, 0~9, -, +).
< > : move on the previous or next letter.
4 Select STORE using the /\ \/ button and then press the > button. And press
the /\ \/ button to select the OK.
5 Press the EXIT/CANCEL button to exit the menu.

Activating the Child Lock

This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmers by muting
out video and audio. Child Lock cannot be released using front panel buttons. Only remote control can release the Child Lock
setting, so keep the remote control away from children.
1 Press the TV.MENU button. The OSD MENU will be displayed.
2 Select SETUP using the /\ \/ button and then press the > button.
3 Select MANUAL PROGRAM using the /\ \/ button and then press the >
button.
4 Select CHILD LOCK using the /\ \/ button and then press the > button.
5 To lock the channel, select LOCK by pressing the /\ \/ button.

Activating the Child Unlock

1-4 STEP1~STEP4 is the same as that of Activating the Child Lock.
5 When a login dialog box appears, enter the password to deactivate the CHILD LOCK.

Note

• When child lock is activated, only entering the correct password will proceed to the operation
before you can do auto or manual searches. Everything previously locked will be unlocked.

Program Edit

This function enables you to delete, copy, move or
skip the stored programs.
1 Select the channel to tune using the numeric or channel buttons.
2 Press the TV.MENU button. The OSD MENU will be displayed.
3 Select SETUP using the /\ \/ button and then press the > button.
4 Select PROGRAM EDIT using the /\ \/ button and then press the > button.

Delete a Program

1 Select a program to the deleted with the \/ /\ < > buttons.
2 Press the RED button. The selected program is deleted. All the following programs are shifted up one position.

Moving a Program

1 Select a program to the moved with the \/ /\ < > buttons.
2 Press the GREEN button.
3 Move the program to the desired program number with the \/ /\ < > buttons.
4 Press the GREEN button again to release this function.

10 PRESTIGIO P260MW / P260DVD-X - PRESTIGIO P320MW / P320DVD-X

ENG

Copy a Program

1 Select a program to the copied with the \/ /\ < > buttons.
2 Press the YELLOW button. All the following programs are shifted down one position.

Skipping a Program Number

1 Select a program to the skipped with the /\ \/ < > buttons.
2 Press the BLUE button. The skipped program turns to Magenta.
3 Press the BLUE button again to release this function.
When a program number is skipped it means that you will be unable to select it using the /\ \/ button during normal TV
viewing. If you want to select the skipped program, directly enter program number with the number buttons or select it in
the program edit or table menu.

Changing Channel

1 Using the CHANNEL buttons
Press the PROG \/ /\ buttons to change channels.
You will see all the channels that the TV has memorized.(The TV must have memorized at least three channels.)
2 Using the NUMBER buttons

- To change to single-digit channels(0~9) faster, press “0” before the single digit.
Example: For channel 4, press “0”, then “4”.

- To select a channel over 10, press the -/— button first.
Example: For channel 42, press “-/—”, then “4”, then “2”.
3 Using the Previous Channel
Press the PRE button on the remote control.
The TV changed to the last channels to the last channel you were watching.

When the Picture Quality is Poor or Unstable

Use fine tuning to adjust a particular channel for better picture quality when noise interferes, color quality is poor, or the
screen is unstable.
1 Select the channel to tune using the numeric or channel buttons.
2 Press the TV.MENU button. The OSD MENU will be displayed.
3 Select SETUP using the /\ \/ button and then press the > button.
4 Select MANUAL PROGRAM using the /\ \/ button and then press the >
button.
5 Select FINE TUNE using the /\ \/ button and then press the > button.
6 Press the /\ \/ button to fine tune and then press the > button.
If you are unable to fine-tune a channel, check that the SYSTEM settings are correct.
7 Select STORE using the /\ \/ button and then press the > button. And press the /\ \/ button to select OK.
8 Press the EXIT/CANCEL button to exit the menu.

Selecting the Picture Status

You can select a video mode from among USER, STANDARD, DYNAMIC, or MILD mode according to your personal preference.

QUICK! Press the P.STD button.

Whenever you press this button, PICTURE STATUS changes to USER > STANDARD > DYNAMIC > MILD mode, in this order.
1 Press the TV.MENU button. The OSD MENU will be displayed.
2 Select PICTURE using the /\ \/ button and then press the v button.