Prestige RAY 7R User Manual
RAY 7R MOVING BEAM
USER MANUAL
! ! ! 2!
Ray 7R Moving Beam – User manual
TABLE OF CONTENTS
1Summary 3!
Product Introduction 3!
Content List 3!
2. Safety Information 3!
Safety notes 3!
Safety instructionS 4!
3. Product diagram 5!
4. Features 5!
Installation 6!
Safety 6!
Equipment mounting bracket installation 6!
Device Power 7!
Light Bulb Instructions 8!
Operating and control methods 9!
Control Panel Instructions 9!
Control panel menu functions: 10!
The Control Panel: 12!
Function Table of DMX Control Channel 14!
5. Trouble Shooting 17!
6. Technical Specifications 19!
! ! ! 3!
Ray 7R Moving Beam – User manual
1. SUMMARY
Thank you for purchasing our Ray 7R Moving Beam. Please read these instructions
carefully before operating the system to avoid any possible damage or misuse.
PRODUCT INTRODUCTION
The Ray 7R Moving Beam is an ultra-quiet product that encompasses advanced stage
light technology which is smart, efficient, and smooth to operate. It has internationally
advanced electronic control technology and an intuitive industrial design.
CONTENT LIST
o Ray 7R Moving Beam (x1)
o User Manual (x1)
o Drawbridge (x1)
o Signal Line (x1)
o Power cord (x1)
o Bulb (x1)
2. SAFETY INFORMATION
SAFETY NOTES
Seek advice from a professional prior to authoring any repairs
Always ensure the system is disconnected from the power source before assembling,
deconstructing and moving
Avoid direct eye exposure when in use
! ! ! 4!
Ray 7R Moving Beam – User manual
SAFETY INSTR UCTIONS
o The projector needs to be positioned so that the projection surface is at least
12 meters away from the lens of the projector.
o The projector must be positioned so that it is at least 0.2 metres away from
flammable objects. Do NOT mount the fixture on flammable surfaces.
o Do not operate the projector if the ambient temperature exceeds 40° C
o This fitting has an IP20 protection rating; it is not waterproof.
o The projector must be connected to a power supply system fitted with an
efficient earthing line (Class I appliance according to standard EN 60598-1)
o A qualified electrical installer is required to connect the projector to the main
electrical source.
o Ensure that the main frequency and voltage of the power source corresponds
with projector (according to the electrical data label)
o The maximum temperature that can be reached on the external surface of the
fitting in a thermally steady state is 100° C
o Before starting any maintenance work or cleaning the projector, disconnect
from the main power supply.
o After switching off, do not remove any parts of the fitting for at least 35
minutes to avoid getting burnt.
o The fitting is designed to hold in any splinters produced by a lamp exploding.
The lenses must be mounted and, if visibly damaged, they have to be replaced
with genuine spares.
o Carefully read the ‘operating instructions’ provided by the lamp manufacturer
before operating the lamp. Immediately replace the lamp if it is damaged or
deformed.
o The products referred to in this manual conform to the European Community
Directives to which they are:
o Low Voltage 2006/95/CE
o Electromagnetic Compatibility 2004/08/CE
3. PRODUCT DIAGRAM
4. FEATURES
o Channel mode: 17 international standard DMX512 channels
o Scanning: A wide range of high-speed scanners, including a Horizontal
scanner (540°) and aVertical scanner (270°), each with a 16 bit scanning
accuracy. It is both smooth and precise, and the scanning speed is adjustable.
o Color wheel: 14 color film + white light;
o Gobo wheel: 17 fixed gobos + white circle;
o Prism wheel: includes an eight-prism, and can rotate in both a positive and
negative direction with 16 macro functions;
o Dimming :0%~100% Linear dimming;
! ! ! 5!
Ray 7R Moving Beam – User manual
! ! ! 6!
Ray 7R Moving Beam – User manual
o Focusing :Electronic zoom, Advanced Micro Devices, smooth adjustment of
focal distance;
o Atomization: 0%~100% Linear adjustment of atomization effect;
o LCD panel with blue and white which makes it clear and easy to read the
content displayed;
INSTALLATION
SAFETY
o This fixture requires professional installation. Please note that the customer
takes full responsibility for the installation of this fixture.
o Ensure all parts of the fixture are in good condition before installing.
o Ensure the point of anchorage is stable before positioning the projector
o The safety chain must be properly hooked onto the fitting and secured to the
framework, so that if the primary support system fails, the fitting falls as little
as possible.
EQUIPMENT MOUNTING BRACKET INSTALLATION
There are transport protection locks on the X and Y axis to facilitate installation and
removal.
The specific method is as shown below.
X-axis of the lock-bit pattern (2)
Y-axis of the lock-bit pattern (3)
Loading...