Prestige APS-122E Installation Manual
Model APS-122E
Installation Manual
Remote Control Vehicle
Security System
Table Of Contents:
Before You Begin Page 2
Wire Harness Quick View Page 3
Installation Of The Major Components Page 4
7 Pin Main Wire Harness Page 5-6
2 Pin LED/Valet Connector Page 6
3 Pin Door Lock Connector & Wiring Page 7
Completing Your Installation Page 7
Dome Delay Learn Procedure Page 7
Adjusting The Shock Sensor Page 8
Final Steps Wire Dressing And Operation Explanation Page 8
Programming Transmitters Page 9
Programming Alarm Feature Bank 2 Page 9
Circuit Wiring Layout Diagram Page 12
PATENTED: www.voxxintl.com/company/patents
Page 1
128-9346
1 of 12
Before You Begin
PROFESSIONAL INSTALLATION IS
STRONGLY RECOMMENDED
Roll down window to avoid locking the keys in the vehicle during installation.
Avoid mounting components or routing wires near hot surfaces or near moving parts like the steering wheel as it may prevent proper operation of the
vehicle.
Tape or loom wires under the hood and dash for protection as well appearance.
Use grommets when routing wires through metal surfaces to prevent chang
and shorting.
Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE
A "TEST LIGHT" OR "COMPUTER SAFE PROBE" as these can set off air
bags or damage sensitive vehicle computers and electronics.
For technical support go to www.avxtech.com
or call 1 800 225 6074
This device complies with FCC Rules Part 15 Operation is subject to the following two conditions
(1) This device may not cause harmful interference and
(2) This device must accept any interference that may be received, including interference that may cause
undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modi-
cations to this equipment. Such modications could void the user’s authority to operate the equipment
Page 2
128-9346
2 of 12
7 Pin Input/Output Wiring Harness Part # 1124315
1 WHITE/BLACK (+) Siren Output
2 ORANGE (-) Starter Inhibit Relay Output
3 DARK BLUE Channel 3 Trunk Output (-) 250mA
4 PURPLE (+) Positive Door Trigger Input
5 BROWN (-) Negative Door Trigger Input
6 DK. GREEN (-) Trigger Input Hood & Trunk
7 YELLOW Ignition Input Switched +12 Volts
2 Pin Door Lock Output Harness Part #1122242
1 Red Neg. Lock / Pos. Unlock 300mA Max
2 Green Pos. Lock / Neg. Unlock
4 Pin Main Power Harness Part #1124314
1 White Parking Light Output (+)
2 White/Red (+) 12 VDC Parking Light Power Input
3 Black Chassis Ground
4 Red (+) 12 VDC Module Power Supply
Page 3
128-9346
3 of 12
INSTALLATION OF MAJOR COMPONENTS:
Control Module: P/N 1365441
Select a mounting location inside the passenger compartment (up behind the dash) and secure using two
screws provided. The control module can also be secured in place using cable ties.
CAUTION: Do not mount the control module in the engine compartment, as it is not waterproof. You should
also avoid mounting the unit directly onto factory installed electronic components. These components may
cause RF interference, which can result in poor transmitter range or intermittent operation. The shock sensor integral of the module will have to be adjusted later so be sure to have the adjustment potentiometer
accessible after mounting.
Siren: P/N AS9903E
Select a mounting location in the engine compartment that is well protected from access below the vehicle.
Avoid areas near high heat components or moving parts within the engine compartment. To prevent water
retention, the ared, or opened end, of the siren must be pointed downward when mounted. Mount the siren
to the selected location using the screws and bracket provided.
Hood Or Trunk Pin Switch: (Optional) P/N 1363699
A pin switch is for use in protecting the hood or trunk (or hatchback) of the vehicle.
The switch must always be mounted to a grounded, metal surface of the vehicle. It is important to select a
location where water cannot ow or collect and to avoid all drip “gutters” on hood and trunk fender walls.
Choose locations that are protected by rubber gaskets when the hood or trunk lid is closed.
The pin switch can be mounted using a bracket when required or directly mounted by drilling a 9/32" diam-
eter mounting hole.
Keep in mind that when properly mounted, the plunger of the pin switch should depress at least 1/4" when
the hood or trunk lid is closed.
LED: P/N 136B1286
A small red LED is included that will serve as a visual indicator of the alarm status. It should be installed in
the dash, located where it can be easily seen from outside the vehicle, yet not be distracting to the driver.
Once a location has been selected, check behind the panel for wire routing access, and to conrm the drill
will not damage any existing components as it passes through the panel.
Drill a 1/4" diameter hole, and pass the red and blue wires from the LED through the hole, from the front of
the panel. Firmly press the body of the LED into the hole until fully seated.
Push Button Valet/Override Switch: P/N 154B1090
Select a desired mounting location for the switch, that is easily accessible to the driver of the vehicle. The
switch does not have to be concealed, however, concealing the switch is always recommended, as this
provides an even higher level of security to the vehicle. The switch may be mounted below the dash using
one of the brackets provided, or mounted in the dash by drilling a 1/4" diameter hole in the location. Be sure
to check behind the dash for adequate clearance for the body of the switch, and to conrm that the drill will
not damage any existing components as it passes through the dash.
Whichever mounting method is used, make certain the back of the switch is accessible for wiring later in
the installation.
Page 4
128-9346
4 of 12
Loading...