PRESIDENT GRANT II PREMIUM Service Manual

GRANT II

PREMIUM

SERVICE MANUAL

-TECNNICAL CHARACTERITICS

1-GENERAL:

-Multiconfiguration (EU, PL, d, EC, U, In)

-EU  40 channels AM/FM 4W-USB/LSB 12WPEP

(from 26,965Mhz to 27,405Mhz)

-PL  40 channels AM/FM 4W (from 26,960Mhz to 27,400Mhz)
40 channels USB/LSB 12WPEP (from 26,965Mhz to 27,405Mhz)

-d  80 channels FM 4W (from 26,565Mhz to 27,405Mhz)

40 channels AM 4W-USB/LSB 12WPEP (from 26,965Mhz to 27,405Mhz)

-EC  40 channels FM 4W (from 26,965Mhz to 27,405Mhz)

-U  40 channels AM/FM 4W-USB/LSB 12WPEP (from 26,965Mhz to 27,405Mhz)
40 channels FM 4W (from 27,60125Mhz to 27,99125Mhz)

-In  27 channels AM/FM 4W (from 26,965Mhz to 27,275Mhz)

-Channel step

-10KHz

-Class of emission

-AM(A3E)/FM(F3E)/USB LSB(J3E)

-Power supply

-13,2V (from10,8V to 15,6V)

-Antenna impedance

-50

-Dimensions(in mm)

-185(W)x250(D)x56(H)

-Weight

-1,250Kg

2-TRANSMISSION:

-Frequency allowance

-±300Hz

-Transmission interference

-Inferior to 4nW(-54dBm)

-Audio frequency response

-From 300Hz to 3kHz

-Emitted power in the adjacent channel

-Inferior to 20µW

-Microphone sensitivity

-Inferior to 3mV

-Current drain

-3A(in transmission mode with modulation)

-Modulated signal distortion

-Inferior to 2%

3-RECEPTION:

-Maximum sensitivity at 20dB sinad

-0,5µV(-113dBm) AM/0,35µV(-116dBm) FM/0,28µV(-118dBm)USB LSB

-Audio frequency response

-From 300Hz to 3kHz

-Adjacent channel selectivity

-Superior to 60dB

-Frequency image rejection

-Superior to 60dB

-Intermodulation response

-Superior to 54dB

-Maximum audio power

-3W

-Squelch sensitivity

-Threshold 0,2µV(-120dBm)/Tight 1mV(-47dBm)

-Current drain

-400mA nominal/1000mA maximum

ALIGNMENT PROCEDURE

(GRANT II PREMIUM)

* VCO/PLL PORTION

- Alignment procedure

- Test points

- Frequencies chart

* TRANSMITTER

- Alignment procedure

- Test points

* RECEIVER

- Alignment procedure

- Test points

Test equipement required

Frequency counter 200 Mhz HF Generator
DC Volmeter & DC Amperemeter BF Volmeter
Distortiometer HF Volmeter
Wattmeter - Dummy load Osilloscope
FM linear detector Load 8 Ω
AF generator Sinad meter

Conditions of Measurements on HF Generator

Reception

AM mode: Level - 107 dBm Frequency 1 KHz with 60% of modulation.
FM mode: Level - 107 dBm Frequency 1 KHz with 1,2KHz of deviation.
USB/LSB mode: Level - 107 dBm

Transmission

Frequency1,25 KHz 30mV AM/FM

Frequency two tones 0,4 KHz 30mV & 2,5KHz 30mV

ALIGNMENT VCO/PLL

1 - Alignment procedure(13,2V;configuration” EU, PL, d, EC, U, In ”)

STEP

CONDITION ADJUSTMENT

REMARKS OF ADJUSTMENT

1

AM/FM(EU)

RX mode

Channel 20

L304

Clarifier center position
Connect a frequency counter to TP302,
adjust L304 to reach 37,900MHz ± 20Hz

2

USB(EU)
RX mode

Channel 20

L306

Clarifier center position
Connect a frequency counter to TP303,
adjust L306 to reach 10,6975MHz ± 20Hz

3

LSB(EU)
RX mode

Channel 20

L307

Clarifier center position
Connect a frequency counter to TP303,
adjust L307 to reach 10,6925MHz ± 20Hz

4

AM/FM(EU)

TX mode

Channel 20

L305

Clarifier center position.Connect a
frequency counter to the dummy load,
adjust L305 to reach 27,205MHz ± 20Hz

5

FM(U)

TX mode

Channel 20

RT302

Clarifier center position.Connect a
frequency counter to the dummy load,
adjust RT302 to reach 27,78125MHz ±
20Hz

6

AM(EU)

RX mode

Channel 40

Clarifier center position. Connect a
voltmeter to TP 301 and check
1,4V±0,2V.

7

AM(EU)

RX mode

Channel 01

Clarifier center position. Connect a
voltmeter to TP 301 and check
1,2V±0,2V.

8

AM/FM

RX mode

(EU,PL,d,EC,U,In)

Clarifier center position

Connect a frequency counter to TP302,
and check with the frequency list

- FREQUENCY LIST (EU,EC)

CH

Channels

Frequencies

(MHz)

VCO(TP302)

Frequencies

(MHz)

1 26,965 37,660
2 26,975 37,670
3 26,985 37,680
4 27,005 37,700
5 27,015 37,710
6 27,025 37,720
7 27,035 37,730
8 27,055 37,750

9 27,065 37,760
10 27,075 37,770
11 27,085 37,780
12 27,105 37,800
13 27,115 37,810
14 27,125 37,820
15 27,135 37,830
16 27,155 37,850
17 27,165 37,860
18 27,175 37,870
19 27,185 37,880
20 27,205 37,900
21 27,215 37,910
22 27,225 37,930
23 27,255 37,950
24 27,235 37,930
25 27,245 37,940
26 27,265 37,960
27 27,275 37,970
28 27,285 37,980
29 27,295 37,990
30 27,305 38,000
31 27,315 38,010
32 27,325 38,020
33 27,335 38,030
34 27,345 38,040
35 27,355 38,050
36 27,365 38,060
37 27,375 38,070
38 27,385 38,080
39 27,395 38,090
40 27,405 38,100

- FREQUENCY LIST (PL)

CH

Channels

Frequencies

(MHz)

VCO(TP302)

Frequencies

(MHz)

1 26,960 37,655

2 26,970 37,665

3 26,980 37,675

4 27,000 37,695

5 27,010 37,705

6 27,020 37,715

7 27,030 37,725

8 27,050 37,745

9 27,060 37,755
10 27,070 37,765
11 27,080 37,775
12 27,100 37,795
13 27,110 37,805
14 27,120 37,815
15 27,130 37,825
16 27,150 37,845
17 27,160 37,855
18 27,170 37,865
19 27,180 37,875
20 27,200 37,895
21 27,210 37,905
22 27,220 37,915
23 27,250 37,945
24 27,230 37,925
25 27,240 37,935
26 27,260 37,955
27 27,270 37,965
28 27,280 37,975
29 27,290 37,985
30 27,300 37,995
31 27,310 38,005
32 27,320 38,015
33 27,330 38,025
34 27,340 38,035
35 27,350 38,045
36 27,360 38,055
37 27,370 38,065
38 27,380 38,075
39 27,390 38,085
40 27,400 38,095

- FREQUENCY LIST (U)

CH

CEPT

Channels

Frequencies

(MHz)

VCO(TP302)

Frequencies

(MHz)

1 26,965 37,660

2 26,975 37,670

3 26,985 37,680

4 27,005 37,700

5 27,015 37,710

6 27,025 37,720

7 27,035 37,730

8 27,055 37,750

9 27,065 37,760
10 27,075 37,770
11 27,085 37,780
12 27,105 37,800
13 27,115 37,810
14 27,125 37,820
15 27,135 37,830
16 27,155 37,850
17 27,165 37,860
18 27,175 37,870
19 27,185 37,880
20 27,205 37,900
21 27,215 37,910
22 27,225 37,930
23 27,255 37,950
24 27,235 37,930
25 27,245 37,940
26 27,265 37,960
27 27,275 37,970
28 27,285 37,980
29 27,295 37,990
30 27,305 38,000
31 27,315 38,010
32 27,325 38,020
33 27,335 38,030
34 27,345 38,040
35 27,355 38,050
36 27,365 38,060
37 27,375 38,070
38 27,385 38,080
39 27,395 38,090
40 27,405 38,100

- FREQUENCY LIST (U)

CH

ENG

Channels

Frequencies

(MHz)

VCO(TP302)

Frequencies

(MHz)

1 27,60125 38,29625

2 27,61125 38,30625

3 27,62125 38,31625

4 27,63125 38,32625

5 27,64125 38,33625

6 27,65125 38,34625

7 27,66125 38,35625

8 27,67125 38,36625

9 27,68125 38,37625
10 27,69125 38,38625
11 27,70125 38,39625
12 27,71125 38,40625
13 27,72125 38,41625
14 27,73125 38,42625
15 27,74125 38,43625
16 27,75125 38,44625
17 27,76125 38,45625
18 27,77125 38,46625
19 27,78125 38,47625
20 27,79125 38,48625
21 27,80125 38,49625
22 27,81125 38,50625
23 27,82125 38,51625
24 27,83125 38,52625
25 27,84125 38,53625
26 27,85125 38,54625
27 27,86125 38,55625
28 27,87125 38,56625
29 27,88125 38,57625
30 27,89125 38,58625
31 27,90125 38,59625
32 27,91125 38,60625
33 27,92125 38,61625
34 27,93125 38,62625
35 27,94125 38,63625
36 27,95125 38,64625
37 27,96125 38,65625
38 27,97125 38,66625
39 27,98125 38,67625
40 27,99125 38,68625

- FREQUENCY LIST (d)

CH Channels VCO(TP302) CH Channels VCO(TP302)

d Frequencies Frequencies d Frequencies Frequencies

(MHz) (MHz) (MHz) (MHz)

1 26,965 37,660 41 26,565 37,260

2 26,975 37,670 42 26,575 37,270

3 26,985 37,680 43 26,585 37,280

4 27,005 37,70 44 26,595 37,290

5 27,015 37,710 45 26,605 37,300

6 27,025 37,720 46 26,615 37,310

7 27,035 37,730 47 26,625 37,320

8 27,055 37,750 48 26,635 37,330

9 27,065 37,760 49 26,645 37,340
10 27,075 37,770 50 26,655 37,350
11 27,085 37,780 51 26,665 37,360
12 27,105 37,800 52 26,675 37,370
13 27,115 37,810 53 26,685 37,380
14 27,125 37,820 54 26,695 37,390
15 27,135 37,830 55 26,705 37,400
16 27,155 37,850 56 26,715 37,410
17 27,165 37,860 57 26,725 37,420
18 27,175 37,870 58 26,735 37,430
19 27,185 37,880 59 26,745 37,440
20 27,205 37,900 60 26,755 37,450
21 27,215 37,910 61 26,765 37,460
22 27,225 37,930 62 26,775 37,470
23 27,255 37,950 63 26,785 37,480
24 27,235 37,930 64 26,795 37,490
25 27,245 37,940 65 26,805 37,500
26 27,265 37,960 66 26,815 37,510
27 27,275 37,970 67 26,825 37,520
28 27,285 37,980 68 26,835 37,530
29 27,295 37,990 69 26,845 37,540
30 27,305 38,000 70 26,855 37,550
31 27,315 38,010 71 26,865 37,560
32 27,325 38,020 72 26,875 37,570
33 27,335 38,030 73 26,885 37,580
34 27,345 38,040 74 26,895 37,590
35 27,355 38,050 75 26,905 37,600
36 27,365 38,060 76 26,915 37,610
37 27,375 38,070 77 26,925 37,620
38 27,385 38,080 78 26,935 37,630
39 27,395 38,090 79 26,945 37,640
40 27,405 38,100 80 26,955 37,650

TP 303

TP 302

TP 301

L 304 RT 302

L 307 L 305 L 306

ALIGNMENT VCO/PLL

ALIGNMENT TRANSMITTER

1 - Alignment procedure(13,2V;configuration”EU”)

-Connect a DC amperemeter between the power supply

and the transceiver.

STEP

CONDITION

ADJUSTMENT REMARKS OF ADJUSTMENT

1

USB(EU)

Channel 20

TX mode

without modulation

RT201 CCW
RT202 CCW

Check 0,55A±10mA on the
amperemeter

2

USB(EU)

Channel 20

TX mode

without modulation

RT201

Adjust RT201 to add
0,1A±10mA=0,65A±10mA

3

USB(EU)

Channel 20

TX mode

without modulation

RT202

Adjust RT202 to add
0,1A±10mA=0,75A±10mA

4

USB(EU)

Channel 20

TX mode

with modulation

0,4KHz&2,5KHz

(adjust audio frequency

level to become

0,5WPEP)

L217
L218
L219

Adjust L217, L218, L219 to reach the
maximum power on the RF power
meter.

5

AM(EU)

Channel 20

TX mode
RT207 CW
RT205 CW

1,25Khz 30mV

L216

RT203

1-Adjust L216 to maximum reading
on the RF power meter
2-Turn 180° to CCW after adjust
3-Set RT 203 to center position

STEP

CONDITION

ADJUSTMENT REMARKS OF ADJUSTMENT

6

USB(EU)

Channel 20

TX mode

with modulation

0,4KHz&2,5KHz

(30mV RMS)

RT203

Adjust RT203 to reach
11Wpep ± 0,5W on the RF power
meter.

7

USB(EU)

Channel 20

TX mode

without modulation

RT206

Connect RF probe to TP 201.
Adjust RT 206 to minimum reading
on oscilloscope.

8

FM(EU)

Channel 20

TX mode

without modulation

RT204

Adjust RT204 to reach 3,8W ±
0,1W on the RF power meter.

9

AM(EU)

Channel 20

TX mode

1,25Khz 30mV

RT205
RT207

1-Set RT207 to CW
2-Adjust RT205 to 95%
3-Adjust RT207

90% ± 3% modulation

10

FM(EU)

Channel 20

TX mode

1,25Khz 30mV

RT301

Adjust RT301 to reach 1,9Khz ±

0,1Khz of deviation..

11

AM(RU)

Channel 20

TX mode

without modulation

RT208

Adjust RT208 to reach 8W ±
0,1W on the RF power meter.

12

FM(RU)

Channel 20

TX mode

without modulation

RT209

Adjust RT209 to reach 20W ±
0,1W on the RF power meter.

13

USB(RU)

Channel 20

TX mode

with modulation

0,4KHz&2,5KHz

(30mV RMS)

RT210

Adjust RT210 to reach
20Wpep ± 0,5W on the RF power
meter.

ALIGNMENT TRANSMITTER

L 217

L 218

L 219

L 216

RT 202

RT 201

RT 210

RT 203

RT

206

RT 205

RT 207

RT 301

RT 209 RT 208 RT 204

ALIGNMENT RECEIVER

1 - Alignment procedure(13,2V;configuration”EU”)

STEP

CONDITION

ADJUSTMENT REMARKS OF ADJUSTMENT

1

FM(EU)

Channel 20

Middle volume level.

No squelch active

NB/ANL/HICUT OFF

L19

Connect HF generator(27,205MHz)
to jack antenna adjusted at
(–47dBm 1KHz mod 1,2Khz
déviation).
Connect DC voltmeter to TP1 and
adjust L19 to reach 3 ± 0,1V

2

AM(EU)

Channel 20

Middle volume level.

Squelch control CW

NB/ANL/HICUT OFF

RT3

Connect HF generator(27,205MHz)
to jack antenna adjusted at
(–47dBm 1KHz mod
60%modulation).
Adjust RT3 CW direction so that the
signal is audible.

3

AM(EU)

Channel 20

Middle volume level.

Squelch control CCW

(ASC ON)

NB/ANL/HICUT OFF

RT1

Connect HF generator(27,205MHz)
to jack antenna adjusted at
( –111dBm without modulation).
Adjust RT1 CW direction so that the
signal is no longer audible.

4

USB(EU)

Channel 20

Middle volume level.

Squelch control CW

NB/ANL/HICUT OFF

RT2

Connect HF generator(27,206MHz)
to jack antenna adjusted at
(–47dBm without modulation).
Adjust RT2 CW direction so that the
signal is audible.

ALIGNMENT RECEIVER

TP 1

L19

RT 1

RT 3 RT2

GRANTII

PREMIUM

BLOC DIAGRAM