Presenza QKA051 Installation Manual And User's Manual

DELUXE STAINLESS STEEL

HANDCRAFTED WORK
CENTRE SINK KIT

INSTALLATION GUIDE
AND USER MANUAL

ITM. / ART. 40801
Model No. QKA051

Table of Contents

Table of Contents ...................................2

Safety Information ..................................2

Warranty ...........................................

Ten Year Limited Warranty ...........................3

Warranty Claim Procedure ...........................3

Pre-Installation ......................................

Planning Installation ................................4

Tools/Materials Required .............................4

Parts Required ....................................4

Package Contents .................................5

Safety Information

READ AND SAVE THESE INSTRUCTIONS

1. Inspect your unit before proceeding. Once you unpack your
unit, check for chips, scratches, cracks, dents or scuff marks.
If any damage is noticed, do not install.

2. Use this unit only in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.

3. Installation work and plumbing must be done by qualied
person(s) in accordance with all applicable codes and
standards.

4. Protect the entire surface during installation.

Installation .........................................

Undermount .......................................6

Topmount .........................................9

Strainer .........................................11

Faucet ..........................................11

Operation ..........................................

Using the Sliding Sink and Colander ...................12

Using the Cutting Board .............................12

Installing the Bottom Grid ...........................12

Care and Cleaning .................................13

Sink, Sliding Sink and Colander .......................13

Cutting Board .....................................13

Service Parts .....................................14

CAUTION: Always wear safety goggles and gloves during
installation to prevent personal injury.

QKA051 2

Warranty

TEN YEAR LIMITED WARRANTY

A thorough inspection must be made before installation and any damage must be promptly reported. We will not be liable for failures or damage that
could have been discovered or avoided by proper inspection and testing prior to installation.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Conglom Kitchen & Bath warrants this product to be
free from defects in materials or workmanship for ten years from the date of purchase. Proof of purchase (original sales receipt) from the original
consumer purchaser must be made available to Conglom Kitchen & Bath for all warranty claims.

This warranty is non-transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the manufacturer’s
instructions. It does not apply in the event of product damage due to the use of other than genuine Conglom Kitchen & Bath replacement parts,
(Replacement parts may be obtained by e-mail at [e-mail] or by calling [phone] between 6:30 am - 3:00 pm AEDT) installation
error, abuse, misuse or improper care and maintenance (whether performed by a plumber, contractor, service provider or member of the purchaser’s
household). The warranty excludes damage due to aggressive air or water conditions, harsh or abrasive cleaners and/or materials.

Under no circumstance shall we be held liable for personal injury or property damage resulting from improper installation or use of this product.
We will not be held liable for inconvenience caused by loss of use of this product, costs incurred for labour or materials, removal and installation
of replacement units, or any other incidental or consequential damages. Costs relating to obtaining access for repair or replacement are the
responsibility of the user.

Our obligation shall be limited to the repair or replacement of a unit (at our discretion) that may prove, by our sole examination, to be defective under
normal use and service during the warranty period.

Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty. These non-warrantable items
include, but are not limited to:

- Improper installation not in accordance with manufacturer’s instructions.

- Dents and/or scratches incurred during shipping, handling, or installation.

- Change in colour or nish due to chemical usage.

- Damage caused by failure to follow care and cleaning guidelines, including damage caused by the use of abrasive cleaners.

- Alterations made to the unit by the purchaser or installer.

- Damage caused by accidental impact, re, ood, freezing, and normal wear.

- Bends and warping caused by forced connections, over-tightened ttings, and inadequate support during installation.

This warranty does not extend to commercial and institutional installation or use.

WARRANTY CLAIM PROCEDURE

If a claimable defect occurs or replacement parts are needed, please contact our customer service team at [e-mail] or

[phone] (6:30 am - 3 pm AEDT, Monday - Friday).

Before you make your call, please ensure that you have:

- Model number or description.

- Proof of sale.

- Details regarding the defect and/or part number.

- Name(s) and address(es) of the owner and/or installer.

3

CONGLOMKB.COM

Please contact [e-mail] or [phone] for further assistance.

Pre-Installation

PLANNING INSTALLATION

Inspect your unit before proceeding. Check the surface for any aws or damage, including dents, bends, bumps, or scuff marks. If any damage

is noticed, do not proceed with installation. Please return the unit to place of purchase for an exchange. If there are any missing parts, please
contact the manufacturer for replacements.

You may choose to install this sink either undermount (from below the counter) or topmount (from above the counter). You must install this sink
only in a counter at least 91.4 cm wide with a solid surface that has a minimum thickness of at least 1.9 cm.

Protect the entire surface of the product during installation to prevent damage.

TOOLS/MATERIALS REQUIRED

Measuring tape Carpenter’s square Wrenches (2)

Saber-saw or

Jig-saw

Silicone sealant Pencil Phillips screwdriver

Flathead

screwdriver

Safety goggles Safety gloves

Electric drill with 1 cm
drill bit and 2.5 cm or

3.8 cm hole saw

Hacksaw Teon tape

Pipe wrench

PARTS REQUIRED (NOT INLCUDED)

NOTE:

Parts not shown to actual size.

QKA051 4

Plastic
ange (1)
(3.8 cm dia.)

Tail pipe (1)

Connecting
nut (1)
(3.8 cm dia.)

Supply lines (2)

Pre-Installation (continued)

PACKAGE CONTENTS

1A

1B

1C

B

A

E

F

C D

K

J

G

H

Part Description Quantity

1A Undermount Sink Template 1

1B Undermount Sink Template 1

1C Topmount Sink Template 1

A Stainless Steel Sink 1

B Bottom grid 1

C Sliding sink 1

D Faucet 1

E Colander 1

F Bamboo cutting board 1

G Topmount clips 10

H Undermount clips 10

J Strainer 1

K Strainer Assembly 1

5

CONGLOMKB.COM

Please contact [e-mail] or [phone] for further assistance.