PME 180 SAFETY &
INSTRUCTION MANUAL
AND PARTS LISTING
11-11-08
PME 180
1800 FLOOREX
1800 356 673
PAGE 1.
Table of contents
PAGE 1. Table of Instructions
PAGE 2. Safety instructions
PAGE 3. Operating Instructions
PAGE 4. Operating Instructions cont…
PAGE 5. Electrical safety
PAGE 6. Problem solving
PAGE 7. Diamond tooling 7”& 5”
PAGE 8. Parts Listing PME 180
PME 180
1800 FLOOREX
1800 356 673
PAGE 2.
Safety instructions
1. Read and understand the instructions on the machine and in this manual and engine manual (if applicable).
Different models may have different parts and controls.
2. Equipment should only be operated by trained personnel, in good physical condition and mental health (not
fatigued). The operator and maintenance personnel must physically be able to handle the bulk weight and power
of this machine.
3. This is a one person machine. Maintain a safe operating distance to other personnel. Remember ‘one machine,
one operator’.
4. This equipment is intended for commercial use.
5. For the operators’ safety and the safety of others, always keep all guards and shrouds in place.
6. Never start or run machine when unattended.
7. This machine is intended for use on floor surfaces such as concrete, terrazzo and other hard surfaces only.
8. Never start or run machine with handle folded or when disk(s) are not in contact with the surface.
9. Do not lend or rent machine without the operating instructions for the machine (and the engine, if applicable.
10. Wear clothing suitable for the job and for the work place including, safety shoes, hard hat, hearing protection,
non fogging vented safety goggles, and dust mask suitable for dust.
11. Keep body parts or any loose clothing away from moving parts. Failure to comply could result in bodily injury.
12. Do not modify machine in any way. Only use genuine PME 180 parts and accessories.
13. Repairs should be performed by qualified persons only.
14. Ensure parts have stopped moving and disconnect power or spark plug when servicing or changing blades or
accessories.
15. Never operate machine in rain or if heavy moisture is present.
16. Petrol is extremely flammable and poisonous. Petrol should only be dispensed in well ventilated areas, and only
when engine is cool.
17. WARNING! POISONOUS EXHAUST GASES. Do not operate petrol powered equipment without adequate
ventilation. Carbon monoxide is and invisible odorless gas that can harm or can kill you.
18. Do not operate PME 180 with any covers or doors removed or open.
19. The PME 180 can produce sound pressure levels greater than 85db. The operator must wear approved safety ear
protection.
20. Do not allow the supply cord to come in contact with the cutting blade/head or other moving parts of this
machine.
PME 180
1800 FLOOREX
1800 356 673
PAGE 3.
Operating instructions
1. Wear clothes suitable for the job and for the work place including, safety shoes, hard hat, hearing protection,
non-fogging vented safety goggles, and dust respirator suitable for dust.
2. WARNING! POISONOUS EXHAUST GASES. Do not operate petrol powered equipment without adequate
ventilation. Carbon monoxide is an invisible odorless gas that can harm or can kill you.
3. Be sure all equipment is tested and tagged prior to use on any job.
4. Inspect entire area to be ground before grinding and remove any bolts or concrete nails (etc) that could damage
diamond tooling or machine which could cause a hazardous situation.
5. Ensure there are no obstacles or existing structures that could present a hazard to the operator. If so, take
necessary action to eliminate the hazard.
6. Lock handle into the operating position and lock in place using the cross knobs, then tilt machine back so handle
is resting on the floor.
7. The blade is removed by inserting screwdriver provided into the bearing unit.
8. Install appropriate diamond tooling or other available tooling into the machine. Only use genuine PME 180
tooling. Failure to comply could result in bodily injury.
9. Tilt machine back onto the disk and ensure handle into the operating position.
10. Ensure the on/off switch is in the off position (push the red button).
11. Connect machine to suitable power outlet. Only use heavy duty power lead suitable for high current use
(preferably 2.5mm2 cable), no longer than 30 meters. (For petrol powered equipment, refer to engine manual for
startup procedure).
12. No power is available within the specified distance, have a qualified person install a suitable power outlet closer
to your work. Alternatively use 4mm2 cable for up to 60 meters.
13. Connect a suitable dust extractor to the machine via a 38mm flexible hose. The machine is designed to take the
standard FLOOREX 50mm hose ends to make connection of dust extractors easy and hassle free. A suitable length
of 50 mm hose can be added after 5 meters of 38mm hose.
14. Keep machine clear of drainage pits and grates or any such hazard. Failure to comply could result in bodily injury
and or could damage the machine or property.
15. Ensure machine is on a level surface and handle is not folded.
16. On the dust extractor.
17. Hold the handles firmly and switch the machine on by pushing the green button.
PME 180
1800 FLOOREX
1800 356 673
PAGE 4.
Operating instructions cont…
18. The switch is an over load switch. If it trips it indicates a problem. (Example; undersize power lead or poor power
to GPO outlet). Refer to previous section for recommendations on power leads. Rectify problem or decrease load
on grinder by using tooling with more surface area. Continuing to use the PME 180 when constant tripping occurs
VOIDS THE WARRANTY!
19. Do not attempt to make any adjustments while the machine is in operation. Any adjustments must only be
performed when machine is stopped and power disconnected.
20. Adjust the wheel height to make the blade sit flat on the floor. This ensures the long life of the coupling. If the
coupling has to flex a lot it generates heat and excessive wear which is not covered by warranty.
21. A few minutes of grinding check the wear of the diamond tooling. This will pay handsomely if the diamonds are
wearing out fast due to soft concrete / abrasive concrete. See section Diamond tooling’
22. See section problem solving for tips on how to grind faster on tough concrete and other ways problems can be
rectified.
23. WARNING! Breathable silica may be generated by use and maintenance of this machine. Silica can cause severe
and permanent lung damage, cancer, and or other serious diseases. Do not breathe the dust. Do not rely on your
sight or smell to determine if dust is in the air. Silica may be in the air without a visible dust cloud. If air
monitoring for silica is not provided by your employer at your work site, you must wear appropriate respiratory
protection when operating or maintaining this equipment. Consult your employer for proper respiratory
protection.
PME 180
1800 FLOOREX
1800 356 673
PAGE 5.
Electrical safety
1. All electrical maintenance and repairs to be carried out by qualified persons only.
2. CAUTION - Line terminals may be alive when main switch is in the off position. Disconnect all power at source
before performing any maintenance or repairs.
3. WARNING - DO NOT operate the machine with any electrical panels open.
4. WARNING - The switch on the PME 180 is an overload switch and will trip when under excessive load The
Overload will automatically reset when safe to do so.
5. Continuing to use the PME 180 when constant tripping occurs, VOIDS THE WARRANTY!
6. Never operate machine in the rain or if heavy moisture is present.
7. The overload is there to protect you and the machine from harm. DO NOT alter or adjust the over load in any
way. If it is faulty, only replace with original part that is identical to the faulty one.
8. Never bypass over current devices in this machine.
9. Never connect or disconnect power cables with voltage present or while under load.
10. Disconnect all power connections and observe lock out / tag out procedures before attempting to carry out any
maintenance or repair on any equipment.
11. Avoid any contact with any rotating parts or driven parts.
12. Never use equipment that has not been tested and tagged (including cords).
13. Before connecting the machine to power, check the condition of all power leads and cables on, or used in
conjunction with the machine. DO NOT USE it if any fault(s) cuts; wear marks, Bare wires out of plugs or sockets,
etc… Get qualified persons to repair and re-tag it as required by regulations in your country.
14. Connect machine to suitable power outlet. Only use heavy duty power lead suitable for high current use
(preferably 2.5 mm cable), no longer than 15 meters. (For petrol powered equipment, refer to engine manual for
startup procedure).
15. If no power is available within the specified distance have a qualified person install a suitable power outlet closer
to your work. Alternatively use 4 mm² cable for up to 30 meters.
PME 180
1800 FLOOREX
1800 356 673
PAGE 6.
Problem solving
Diamond Grinding has many variables. When you understand some of these, you can solve
many problems without a lot of bother and expense.
PROBLEM
CAUSE
REMEDY
WHAT IS IT DOING?
Machine will not
start / run.
No power is
present at cable
end.
Check the power is present
with another tool.
Using another tool confirms power
is present
Machine is trying
to start on glue or
other sticky
substance.
Clear a patch with a scraper
and grind into the glue a little
at a time.
This means it only tackles a small
amount of glue at a time and keeps
the glue residue coated with dust,
preventing glue build-up on the
diamonds.
Power lead is too
small in capacity
or too long.
Upgrade the power lead to
2.5mm² (15meters) max or
4mm² (30 meters max).
The long / small capacity cable is
too restrictive and can’t allow
enough power through for the
machine to start / run properly.
Machine is not
grinding at all.
No blade /
accessories in
unit.
Fit blade. Note; check wear
on machine.
Very hard concrete
or glazed topping
on concrete.
Turn dust extractor down /
restrict flow. Only just control
the dust from escaping.
The extra dust accumulating on the
floor acts as an abrasive between
the segments and the floor thus
exposing the diamonds better.
Place river sand or equivalent
on the floor.
The sand is an abrasive as
described above.
Use softer grade of diamond
tooling.
The softer grade will expose the
diamonds better.
Use coarser diamond tooling.
The coarser diamond tooling can
get through the hard topping
without wearing out the diamonds
too fast.
The diamonds
are wearing out
too fast.
The concrete is:
*Soft
*Abrasive
*Rain Damaged
*A rough finish
(Scarified).
Use a powerful dust extractor
to remove as much dust as
possible.
The dust, as described acts as an
abrasive between the segments
exposing the diamonds
prematurely, wasting them.
Use harder diamond matrix.
The harder segments don’t expose
as easily.
Use tooling with more
segments or area² of
segment.
The tooling with more segments or
area² doesn’t have the same weight
on them, reducing wear.
PME 180
1800 FLOOREX
1800 356 673
PAGE 7.
Diamond tooling 7”& 5”
PART No.
DESCRIPTION
GRIT
SEG
COLOUR
7” CONTRACTOR RANGE
BCGF 720 DTY
Diamond Wheel - 12 Segment - For Very Hard Concrete
30/60
12
YELLOW
BCGF 725 DTG
Diamond Wheel – 12 Segment – Glue Removal, hard concrete
30/60
12
GREEN
BCGF 728 DTS
Diamond Wheel – 12 Segment – Aggressive 25# for epoxy removal
25
12
SILVER
BCGF 745 DTG
Diamond Wheel – 18 Segment – Standard Grinding Wheel
30/60
18
GREEN
BCGF 735 DTG
Diamond Wheel – 24 Segment – Fine Finish, Soft/Medium Concrete
30/60
24
GREEN
7” PREMIUM RANGE – LONG LASTING
CGF 7BTD
Super Premium Diamond Wheel, Extra Long Life, soft-medium concrete
30
18
BLUE
CGF 7CTD
Super Premium Diamond Wheel, Aggressive Removal , soft-med concrete
30 9 WHITE
CGF 7RTD
Super Premium Diamond Wheel, 150# Fine Grade, Medium Bond
150 9 RED
CGF 7STD
Super Premium Diamond Wheel, Extra Soft Bond, for very hard concrete
30 6 BROWN
CGF 7YTD
Super Premium Diamond Wheel, Aggressive Removal, soft bond, hard concrete
30 9 YELLOW
CGF 73TD
Super Premium Diamond Wheel, Extra Aggressive, Med - Hard Concrete
30 3 ORANGE
CGF 76PCD
PCD Diamond Wheel - Extra Aggressive for heavy removal of coatings & glues
PCD 6 PURPLE
CGF 725 DTG
Diamond Wheel – 12 Segment – Glue Removal, hard concrete
30/50
12
GOLD
CGF 745 DTB
Diamond Wheel – 18 Segment – Standard Grinding
30/50
18
BLUE
CGF 735 DTG
Diamond Wheel – 24 Segment – Fine Finish
30/50
24
GOLD
CGF 7150 DTG
Diamond Wheel – 18 Segment – 150# Fine Grade
150
18
RED
PART No.
DESCRIPTION
GRIT
SEG
COLOUR
5” CONTRACTOR RANGE
BCG 420 DTY
5” Diamond Wheel – 9 Segment – Hard Concrete, coating removal
30/60 9 YELLOW
BCG 425 DTS
5” Diamond Wheel – 9 Segment – Coarse Grade 25#
25 9 SILVER
BCG 4445 DTG
4.5” Diamond Wheel – 9 Segment – Medium Concrete
30/60 9 GREEN
BCG 445 DTG
5” Diamond Wheel – 9 Segment – Medium Concrete
30/60 9 GREEN
BCG 455 DTG
5” Diamond Wheel – 18 Segment – Fine Finish, soft/medium concrete.
30/60
18
GREEN
BCG 4515 DTR
5” Diamond Wheel – 18 Segment, Fine Grade 150#
150
18
GREEN
5” PREMIUM RANGE
CG 445 DTG
5” Diamond Wheel – 9 Segment – Aggressive removal
30/60 9 GOLD
CG 455 DTG
5” Diamond Wheel – 18 Segment – Fine Finish, Hard Concrete
30/60
18
GOLD
CG 4515 DTR
5” Diamond Wheel – 18 Segment – Fine Grade 150#
150
18
RED
PME 180
1800 FLOOREX
1800 356 673
PAGE 8.
Parts listing PME 180
PM180001. Main body
PM180002. Axle Swivel body
PM180003. Handle main
PM180004. Hood cover
PM180005. Bearing Assembly
PM180006. Flexible coupling
PM180007. Weight 12.5 kg
PM180008. 22 tooth pulley
PM180009. 24 tooth pulley
PM180010. 25mm taper bush
PM180011. 24mm taper bush
PM180012. 640-8m cog belt
PM180013. Plug motor
PM180014. Socket base motor
PM180015. Box 114x64x30
PM180016. Switch 12 A
PM180017. Motor 1.5 KW
PM180018. Handle grips M14
PM180019. Decal set complete
PM180020. axle spacer
PM180021. Wheels 160mm
PM180022. Diamond wheel
PM180023. Shroud 7’
PM180024. Plug 10 A
PM180025. Wire 3core
PM180026. Washer ¾’
PM180027. Cross knob
PM180028. Bolt & nut M18x45
PM180029. Coach head Screw
PM180030. Cross knob
PM180031. Socket head M10 x 25
PM180032. Nylock nut M10
PM180033. Socket dome head screw
PM180034. Ratchet handle M10 female
PM180035. Spanner blade nut
PM180036. Screwdriver Phillips
PM180037. Gland with support
PM180038. Axle (adjuster)
PM180039. Handle axle
PM180040. Start Switch SE/01
Part no Description
Loading...