Page 1
12-drawer Tall Queen
Assembly Instructions
DATE STAMP
CALL US FIRST
1-877-PREPAC1
1-877-773-7221
Mon - Fri 7am - 4pm PST
10am - 7pm EST
• For help with assembly
• If you have received a damaged or
defective part or are missing hardware.
We will process replacement parts
business days or less. Parts are shipped via
UPS Ground or mail.
in 2
Plat form Storage Bed
Model # BQ-6212
This product is shipped in
4 cartons
1 of 4
+
3 of 4
Make sure you have all cartons.
Sometimes cartons shipped on the same
day get separated and are delivered on
2 of 4
+
4 of 4
Before you call please:
1) Record the following information from the
shipping label on the outside of the box.
You will need it for warranty purposes:
• Ship To Name
• Sales Order Number
2) Note the
3) Review the contents of your shipment to
determine what you are missing. This unit
is shipped in 4 cartons. Make sure you
have received all cartons.
Online Option:
Fill out the Replacement Parts Order form in the Product
Support section of our website: www.prepacmfg.com
product model number.
Required Tools
Screwdrivers
Hammer
Phillips Head
Flat Head
Optional Tools
Using a power screwdriver
will speed up assembly.
Caution
Do not over tighten any screw.
The last few turns of each screw
should be done very slowly or by hand.
Prepac Manufacturing Ltd.
6705 Dennett Place
Delta, BC V4G 1N4
LB-0638
2012-06-20
Page 2
Hardware Identification
Bed Hardware
Drawer Slide Screw
(162)
RM-0074
JRN Nut
(24)
RM-0312
Allen Key
RM-0313
(1)
JCB Connector (24)
RM-0310 bronze (cherry / espresso)
RM-0314 black
Machine Screw
Wing Nut (4)
RM-0322
Metal Brace - Left (2)
Metal Brace - Right (2)
(4)
RM-0321
BF-BRACE-L
BF-BRACE-R
T Spacer
(48)
RM-0628
Black #8 - 9/16"
Washerhead Screws (4)
RM-0521
Package will contain
more than required
Drawer Bottom
Stabilizer (12)
RM-0839
Drawer Slides for Bed
4 per drawer
#8 - 1½” Hi Lo Screws
(48)
RM-0504
1 LEFT Drawer Slide per Drawer (Total = 12)
1 RIGHT Drawer Slide per Drawer (Total = 12)
12mm Zinc Cam
(48)
RM-0715
LEFT Slide (12)
RIGHT Slide (12)
Drawer Hardware
34mm Black Twister Dowel
(48)
RM-0500
5 per drawer
¾” Nail
(60)
RM-0022
8 per drawer
Drawer Slide Screw
(96)
RM-0074
Page 2 of 20
Page 3
Bed Parts
B5
B6
B3
B4
B1
B2
B2
B3
B1
B4
B1
Outer Gables (2)
GA-4130 black
GA-4930 cherry
GA-4630 espresso
B2
Inner Gables (2)
GA-4131 black
GA-4931 cherry
GA-4631 espresso
B3
Upper Stabilizer (2)
ST-4120 black
ST-4920 cherry
ST-4620 espresso
B4
Lower Stabilizer (2)
ST-4121 black
ST-4921 cherry
ST-4621 espresso
B5
B5
Plywood Slats (9)
BF-2000-PW
B6
Metal U-channel with
Blocks (2)
BF-3000-C
Page 3 of 20
Page 4
STEP 1
Estimated Time: 10 minutes
Attach metal U-channels to each outer gable using drawer slide screws
Note: In the center of the U-channels there are two pairs of
holes. Each pair has a small and large hole. Make sure the
LARGE HOLE is positioned to the top of the outer gable.
Large
hole
TOP
TOP
TOP
BOTTOM
BOTTOM
STEP 2
Attach T spacers to outer gables with drawer slide screws.
Estimated Time: 15 minutes
Drawer Slide
Screw
Page 4 of 20
Page 5
STEP 3
Estimated Time: 10 minutes
Attach drawer glides to T-spacers on
outer gables as shown in the photo
Position the Drawer Glides with:
A) The wheel at the finished side
B) The wheel on the unfinished bottom
Finished
Side
Bottom
Use 14th hole
Use 1st hole
Use 1st hole
Use 14th hole
Page 5 of 20
Page 6
STEP 4
Insert JRN nuts into the holes on each end of the inner gables. The
holes are drilled through. You can insert them from either side.
Estimated Time: 5 minutes
B2
B2
Insert the nut as shown, so that
the hole lines up with the hole
on the edge of the gable.
Page 6 of 20
Page 7
STEP 5
Estimated Time: 5 minutes
Insert JRN nuts into the holes on each end
of the upper (B3) and lower (B4) stabilizers.
Upper Stabilizers
B3
Identifying the upper and
lower stabilizers
Upper Stabilizers
Top edge
(FINISHED) is
rounded
Side hole is
close to the
UNFINISHED
edge
Side hole is close to
the finished edge
Lower Stabilizers
Lower Stabilizers
B4
Page 7 of 20
Page 8
STEP 6
Estimated Time: 10 minutes
Attach “T” spacers and drawer glides to Inner Gables
6a
6b
Attach “T” spacers to ONE side of each
inner gable with drawer slide screws
Attach drawer glides to “T” spacers on
inner gables.
Position the drawer glides with:
A) The wheel at the finished edge
B) The wheel on the bottom
Top
7”
Drawer Slide
Screw
4”
Bottom
IMPORTANT:
Before attaching the drawer glides, determine the
TOP and BOTTOM of each inner gable.
Finished
Edge
A. Measure from each edge of the “T” Spacer to
each unfinished edge.
B. The measurement that is approximately 4” will
be the BOTTOM.
Check the position of the drawer glides carefully
before you attach them to the inner gables.
Bottom
4”
Drawer
Slide Screw
Unfinished Edge
Wheel is on the bottom and
toward finished edge
6c
Repeat steps 6a & 6b for the 2nd side
of the inner gables.
Page 8 of 20
Page 9
STEP 7
Using JCB connectors, and the Allen Key provided,
attach each lower stabilizer (B4), one at a time, to both
inner gables BELOW the drawer slide
Estimated Time: 5 minutes
B4
Finished edge
IMPORTANT
Identifying the Lower Stabilizer
The screw hole is at the top, close to the finished edge
If you have any difficulty tightening the JCB connector,
use a screwdriver to adjust the JRN nut to make sure
the hole is facing the opening for the connector
B4
JCB
Connector
JRN
Nut
Page 9 of 20
Page 10
STEP 8
Using JCB connectors, attach each upper stabilizer (B3), one at
a time, to both inner gables.
Estimated Time: 5 minutes
B3
Top edge (FINISHED)
is rounded
Upper Stabilizer
The screw hole is closest
to the lower, unfinished
edge
Page 10 of 20
Page 11
STEP 9
Attach one outer gable (B1) to stabilizers with JCB connectors
Estimated Time: 10 minutes
B1B1
Page 11 of 20
Page 12
STEP 10
Estimated Time: 5 minutes
Lay the four metal braces, as shown, with the bend resting
on top of the inner gables
10a
Find the pre-drilled holes on the inner gables and
secure the bent end of each metal brace to the inner
gables with the small black screw (#8 - 9/16”
Washerhead Screw).
10a
Bend
10a
10a
10b
10a
10b
10a
Pre-drilled hole
10b
10a
Secure the other (flat) end of the metal brackets to U-channel.
Position the flat end of the
metal brace under the hole on
the BOTTOM edge of the Uchannel. Push the outer gable
toward the center of the bed
until holes line up.
Insert machine screw through Uchannel and metal brace and attach
wing nut to the screw.
Insert a screwdriver through the
large hole while holding on to the
wing nut to tighten.
Metal brace secured to
the U-channel
Page 12 of 20
Page 13
STEP 11
Estimated Time: 5 minutes
11a
11 b
Spread the wooden slats out across the inner stabilizers
Slide the slats into the wide spaces of the metal U-channel (B6) on one outer gable. Remember that one
set of metal braces are still loose on one end.
Slide
11b
Page 13 of 20
Page 14
STEP 12
Carefully attach second outer gable to stabilizers
Estimated Time: 10 minutes
This Step easiest with 2 People
12a
12b
12c
Secure the gable in place with with JCB connectors, but don’t fully tighten
Ensure the slats are set inside the u-channel and that they haven’t pulled out of the first outer gable.
Firmly tighten the connectors
STEP 13
Secure the flat end of the remaining metal brackets
to U-channel. Refer to Step 10
Estimated Time: 10 minutes
Page 14 of 20
Page 15
Drawer Parts Identification
D1
Drawer Front (12)
DF-10012-B black
DF-10012-C cherry
DF-10012-E espresso
D2
Left Drawer Side (12)
DS-0415W-L
Plywood
D3
Right Drawer Side (12)
DS-0415W-R
Plywood
D4
Drawer Back (12)
DK-4100W
unfinished
D2
D1
D5
Drawer Bottom (12)
DB-4100
Unfinished
D4
D5
D3
STEP 14
14a
Left Drawer Side
Insert cams into drawer sides
Estimated Time: 5 minutes PER DRAWER
D2
Make sure arrow
faces toward hole for
twister dowel
D3
Right Drawer Side
Page 15 of 20
Page 16
14b
Screw black twister dowels into drawer fronts
D1
14c
ONLINE
HELP
b n
i
e
Attach drawer sides to drawer back with 1½” Hi Lo screws
t Par
t
s
Id
e
ntific
a io
t
nCa
To see a video showing how the cam and
connectors work, please visit our website:
www.prepacmfg.com/support/assemblyvideos.html
1½” Hi Lo Screws
Page 16 of 20
Page 17
14d
Attach drawer front and tighten cams
using a flat head screwdriver
Left Drawer Side
Unlocked
14e
Turn drawer upside down and slide drawer bottom into grooves
Locked
Turn 210°
Unlocked
Right Drawer Side
Locked
Turn 210°
Page 17 of 20
Page 18
14f
Secure the drawer bottom to the
drawer back with nails
Use 4 nails
per drawer
C
14g
Insert the Drawer
Bottom Stabilizer
Position the Stabilizer in the center
of the drawer and insert it into the
groove on the drawer front. This is
the same groove that you inserted
the drawer bottom into.
Then, tighten screw until it is flush
Groove on
drawer front
Page 18 of 20
Page 19
14h
Attach drawer slides to left and right drawer sides using drawer slide screws
Right Drawer Side
Drawer
Slide
Screws
Left Drawer Side
Drawer
Slide
Screws
Page 19 of 20
Page 20
STEP 15
Insert drawers
Estimated Time: 2 minutes
Note: When drawers are installed correctly, you will not be able to
remove them without first lifting up the drawer front.
Furniture Care Q&A
Q. How do I clean your products?
A. We recommend that you simply wipe your products with a clean, damp cloth and then dry immediately with
another clean cloth to maximize the life span and look of your unit
Q. Can I paint or varnish your products?
A. Our products are made from durable composite woods with a laminate finish and therefore should not be
painted or varnished.
Q. Are they waterproof?
A. NO. If liquid is spilled and quickly wiped up, no damage will be done to your product. However, continuous
exposure to liquids or high humidity may cause damage to the board.
Give Us Your Feedback
CALL US: 1-877-PREPAC1 (1-877-773-7221)
Mon - Fri: 7am - 4pm PST / 10am - 7pm EST
Email Us: assembly@prepacmfg.com
Thanks!
Page 20 of 20
Loading...