Premier Storage Systems AE46, E46, AE42, E42, ANE46 Installation Manual

Installation

Manual

MODELS:

AE46, AE42, E46, E42, ANE46, ANE42, NE46, NE42

TABLE OF CONTENTS

SWIVEL UNITS (AE46, AE42, ANE46, ANE42)............................pg.3

NON-SWIVEL UNITS (E46, E42, NE46, NE42)...........................pg.11

ELECTRICAL INSTRUCTIONS.....................................................pg.17

Premier Storage Systems

220 W. Jackson St, Morton, IL 61550

1-800-536-9495 or [e-mail]

3

Swivel Units

Models: AE46, AE42, ANE46, ANE42

Tools Needed:

Supplied Parts:

Recessed Mounting:

- Two #10 x 1 1/2” wood screws for top

portion of cabinet

- Two #14 x 2 1/2” Phillips screws for top
side brackets

Surface Mounting:

- Two #14 x 4” wood screws

3

GET TO KNOW YOUR UNIT

1. CROSS BRACES

- Three braces for 46” units

- Two braces for 42” units

2. ELECTRICAL RACEWAY
(AE46, AE42)

3. SIDE BRACKETS

4. ELECTRICAL CORD COVER
(AE46 only; AE42

features a cord wrap)

5. ELECTRICAL OUTLET

6. HOT IRON REST
(AE46, ANE46)

2

4

1

6

6

1

ELECTRICAL MODELS

(AE46 SHOWN)

NON- ELECTRICAL MODELS

(ANE46 SHOWN)

(BOTTOM OF RACEWAY)

- Stud Finder

- 12-14” Level

- Tape Measure

- Small Flathead
Screwdriver

- Electric Drill
(with 1/4” & 1/8” drill bit)

- 1/4” Nut Driver
(optional)

- Safety Glasses

- Utility Knife

3

4 - Swivel Installation

SWIVEL: PRE-INSTALLATION

Desired Ironing

Board Height

AE46 & ANE46

Mounting

Height Above

Floor

29”
28”
27”
26”

36”
35”
34”
33”

Desired Ironing

Board Height

AE42 & ANE42

Mounting

Height Above

Floor

25”
24”
23”
22”

36”
35”
34”
33”

2. LOCATE STUDS & UTILITIES

Using a stud nder, locate the wall

studs to be used for mounting.

Locate the existing wiring or other
utilities in the wall to prevent drilling
into/severing a wire and/or other utility
during installation.

1. DETERMINE MOUNTING HEIGHT

Using the charts provided, determine
the mounting height above oor (the
distance between the oor and the
bottom of the cabinet). First choose
your desired ironing board height
from the left column, then locate the
corresponding mounting height in the
right column.

Mounting

Height

Above Floor

Desired Ironing

Board Height

Refer to the chart provided below to ensure
adequate clearance for ironing. The cabinet
door opens at 180 degrees; allow 16” from side
of cabinet for door to fully open.

3. ENSURE ADEQUATE SPACE

AE46

ANE46

2. Distance from wall to tip of ironing board

50

7/8

” 46

7/8

”

AE42

ANE42

4. Standing area clearance (not shown)

The suggested distance from the side of the ironing where the user
typically stands to ensure adequate space for ironing.

16

7/8

” 14

5/8

”

1. Distance needed on either side of unit to fully swivel the board

3. Distance from wall to board when in full swivel position

32

7/8

” 32

7/8

”

24” 24”

Swivel Installation - 5

SWIVEL: RECESSED INSTALLATION

Cut an opening into the wall based
on unit dimensions given below.

AE46/ANE46: 14

3/8

” x 59

7/8

” x 3

7/8

”

AE42/ANE42: 14

3/8

” x 51

1/4

x 3

7/8

”

Attach a 2” x 4” cross support
cleat between the studs so it
is level with the bottom of the
opening. This will give support to
the drywall during installation and
the cabinet once installed in the
wall.

Your unit will be attached to the studs by
screws in the upper and lower sides of
the cabinet.

AE46 & AE42: Remove electrical
raceway before proceeding by
removing the top and bottom screws on
the raceway.

Using a 1/8” drill bit, pre-drill holes into
the sides of the cabinet, 14” from the top

and 2

1/2

” from the back.

1. CUT WALL OPENING

2. ATTACH CLEATS

3. PRE-DRILL HOLES

Example shown with exposed

studs & unit to illustrate mounting.

6 - Swivel Installation

14” from top of cabinet

2

1/2

” from back

of cabinet

CLEAT

AE46 SHOWN

Note: Instructions based on installation between 16” on-center studs.