In-Ground Fence
GIG00-16919 | Product Manual
™
Have questions about your In-Ground Fence™ System
or need training tips for your pet?
Our Customer Care representatives are here to help you.
Call our USA-based Customer Care Center at
+1 (866) 381-2785
USA & Canada: Mon–Fri 8am-8pm EST | Sat 9am–5pm EST
This product includes a one year warranty.
Call, click, or chat with us before you return your product.
premierpet.com
Important Safety Information
Explanation of Attention Words and Symbols used in this guide
This is th e safety alert s ymbol. It is us ed to alert you to pote ntial personal i njury hazar ds. Obey all safety me ssages th at
follow thi s symbol to avoid p ossible injur y or death.
WARN ING indicates a haz ardous situatio n which, if not avoi ded, could result in d eath or serious in jury.
CAUTI ON, used with th e safety alert s ymbol, indic ates a hazardous s ituation which , if not avoided, cou ld
result in m inor or moderate i njury.
CAUTI ON, used witho ut the safety ale rt symbol, i ndicates a hazar dous situation w hich, if not avoid ed,
could res ult in harm to your pet .
NOTICE is us ed to address prac tices not related to p ersonal injur y.
• Do no t use this produ ct if your pet i s aggressi ve or is prone to ag gressive b ehavior. Aggre ssive pet s can cause sever e injury and ev en death to
owner s and others. If y ou are unsure w hether this pro duct is appr opriate for your p et, please co nsult your veter inarian or a cer tified trainer.
• Bef ore you begin in stalling the b oundary wir e, turn the tran smitter o.
• Und erground cab les can carry h igh voltage. Have al l undergroun d cables marke d before you dig to b ury the boun dary wire. In m ost areas, th is
is a free s ervice. Do no t install, conn ect or remove y our system du ring a lightnin g storm. If the s torm is close eno ugh for you to hear t hunder, it
is close e nough to create ha zardous surg es.
• To avoid ris k of severe injur y, follow all safet y instruct ions for your p ower tools, an d wear safety go ggles during u se.
• To avoid elec tric shock, u se the transm itter indoor s in a dry locati on only
• DO NOT at tempt to cut into or p ry open the ba ttery. Be sure to di scard any used b attery prop erly.
• Nev er incinerate, pu ncture, defo rm, short-ci rcuit or charg e with an inappro priate charger. Fir e, explosion , propert y damage or bodi ly harm
may occur i f this warning i s not followed.
• The re is a risk of exp losion if a batte ry is replaced b y an incorrec t type. Do not sh ort circuit , mix old and new bat teries, dis pose of in fire or
expos e to water. When batter ies are stored o r disposed , they must be pr otected from s horting.
• Wire o n top of the ground m ay be a trip hazar d. Be careful w hen placing wir es and testin g the system.
• Th is system is NOT a s olid barri er. It is designed to a ct as a deterr ent to remind pe ts to remain wit hin the establ ished boun dary by use of s tatic
correc tion. It is imp ortant that y ou reinforce tr aining with yo ur pet on a regula r basis. Sin ce the tolerance le vel to shock var ies from pet to p et,
Radio Syste ms Corporat ion CANNOT guar antee that the sy stem will, in all c ases, keep a p et within the e stablishe d boundary. Not a ll pets can be
traine d to avoid crossi ng the bounda ry! Therefo re, if you have rea son to believ e that your pet may p ose a danger to oth ers or harm him self if he
is not kept f rom crossin g the boundar y, you should NOT rel y solely upon thi s system to confin e your pet. Radi o Systems Corp oration shall N OT be
liable for a ny propert y damage, eco nomic loss or a ny conseque ntial damage s sustained a s a result of any ani mal crossin g the boundar y.
• Th is product i s not a toy. Keep it away fro m the reach of child ren.
• Pro per fit of the collar i s important . A collar worn for t oo long or made too t ight on the pet’s ne ck may cause skin d amage, rangin g from
redne ss to pressure u lcers. This con dition is comm only known a s bed sores.
• Avoid le aving the collar o n a pet for more th an 12 hours per day.
• Whe n possible, rep osition the co llar on the pet’s ne ck every 1 to 2 hou rs.
• Regu larly rechec k the fit to prevent e xcessive pre ssure; follow th e instruct ions in this man ual.
• You may ne ed to trim the hair in t he area of the cont act points. H owever, never shav e the dog’s neck; th is may lead to a rash o r infection.
• Nev er connect a lea sh to a collar with co ntact points . It will cause exc essive pres sure on the cont act points.
• Whe n connecting a l eash to a separate c ollar, do not allow it to pu t pressure o n the receiver col lar.
• Wash t he dog’s neck area a nd the contact p oints of the coll ar weekly with a dam p cloth.
• Exa mine the contac t area daily for si gns of a rash or a so re.
• If a ra sh or sore is fou nd, discontin ue using this pr oduct until th e skin has heale d.
• If the c ondition per sists beyo nd 48 hours, s ee your veteri narian.
• For a dditional info rmation on be d sores and pre ssure necro sis, please v isit our webs ite.
• Pro per training of y our pet is esse ntial to success fully using th e system. Dur ing the first 2 we eks of trainin g, do not use the s ystem witho ut
direc t supervis ion of your pet.
• Alway s remove your p et’s receiver coll ar before per forming any tr ansmitter te sting or adjus tments. Thi s will prevent u nintended cor rections.
• The b oundary wi dth of the syst em must be teste d whenever an ad justment is m ade to the pet area to p revent uninten ded correc tions to
your pet . Do not use an outl et protected w ith a residual cu rrent device (R CD) or groun d fault circuit in terrupter (GFCI). The fen ce system will
funct ion properly, bu t in rare cases , nearby light ning strikes m ay cause the RCD or GF CI to trip. Withou t system powe r, your pet may esca pe.
You will have to re set the RCD or GFC I to restore powe r to the system.
• Avoid d amaging the in sulation of the lo op wire; damag e may cause areas o f weak signal and le ad to failure of the b oundary.
• Whe n mowing or tri mming your gra ss, use care n ot to cut the bound ary wire.
• To protect t he transmit ter, disconnec t the boundar y wire and unplu g the power adapte r from the outlet w hen the syst em will not be use d for
long per iods of time or p rior to thunder storms. Th is will preven t power surges f rom damagin g the transmit ter.
+1 (866) 381-27852
TABLE OF CONTENTS
Components 4
How It Works 4
Key Definitions 5
Locate the Fence Transmitter 6
Lay Out the System 6
Position the Boundary Wire 8
Connec t the Wires to the Surge Protector and Fence Transmitter 9
Prepare the Receiver Collar 11
Set the Boundar y Width and Test the Receiver Collar 12
Install the Boundary Wire 13
Place the Boundar y Flag s 14
Fit the Receiver Collar 14
Training Guide 16
Troubleshooting 17
Additional Information 18
System Test 18
Wire Break Location Test 19
Terms of Use and Limitation of Liability 20
Warranty 20
Perchlorate Battery 21
Battery Disposal 21
Compliance 21
Layout Grid 22
Mounting Template 23
premierpet.com 3
Components
Power
Adapter
Receiver Collar
w/Short Contact Points
Fence
Transmitter
Battery
(GAC11-16351)
Boundary Wire -
500 ft
Boundary
Flags - 50
Surge
Protector
Test Light
Tool
Long
Contact
Gel-filled
Capsules
Wire Nuts
Points
Other Items You May Need
• Additional wire and flags (GRFA-500)
• Tape measure
• Small Phillips screwdriver
• Drill & mounting hardware
• Shovel or lawn edger
• Pliers
• Wire stripping pliers
• Scissors
• Lighter
• Electrical tape
• Gel-filled capsules
• Additional wire nuts
• Waterproofing compound (e.g. silicone caulk)
• PVC pipe or water hose
• Circular s aw with ma sonr y blade
• Staple gu n
• Non-metallic collar and leash
Set up and training help: ww w.premierpet.com
How It Works
The Premier Pet™ In-Ground Fence™ system has been proven safe, comfor table, and eective for pets
over 8 lb. The system works by producing a radio signal from the fence transmit ter through up to 2000 ft.
of boundary wire. The boundar y wire is buried or attached to a fixed object to enclose the pet area. You
temporarily define this pet area with boundar y flags for a visual aid in training your pet. Your pet wears a
receiver collar with contact points that touch his neck, and once trained, is allowed to roam freely in the
pet area. When your pet reaches the warning zone, the receiver collar gives a warning beep. If your pet
continues into the static correction zone, a safe static correction will be delivered through the contact
points to get his attention until he returns to the pet area.
+1 (866) 381-27854
Key Definitions
Battery
Contact Points
Washers
Power Light
Loop
Indicator
Light
Boundary
Wire Terminals
Boundary
Width
Control
Power
Jack
Fence
Transmitter
Static
Correction
Zone
Warning
Zone
Static
Correction Zone
Warning
Zone
Boundary
Width
Surge
Protector
with Power
Adapter
Fence Transmitter: Transmits the radio signal through the boundary w ire
Pet Area: The area within the warning zone where your pet can roam freely
Warning Zone: The outer edge of the pet area where your pet’s receiver collar begins to beep, warning
him not to go into the static correction zone
Static Correction Zone: The zone beyond the warning zone where your pet’s receiver collar will emit a
static correction, signaling him to return to the pet area
Boundary Width: The combination of the warning zone and the static correction zone
Surge Protector: Installed with the fence transmitter to protect it from lightning strikes and power surges
Receiver Collar: The device that receives the radio signal from the boundary wire
Correction Level Button: Adjusts the level of static correction your pet receives in the static
correction zone
Receiver Indicator Light: Indicates the level of correction at which the receiver collar is set. This light
also serves as the low bat tery indicator
Contact Points: The contacts through which the receiver collar delivers the safe static correction when
your pet moves into the static correction zone
Power Jack: The jack where the power adapter plugs into the fence transmitter. The fence transmitter is
powered by a standard outlet
Boundary Wire Terminals: The terminals where the boundary wires connect to the fence transmitter in
order to complete a continuous loop
Loop Indicator Light: The light that indicates that the boundary wire makes a complete loop, enabling
the signal to be transmitted
Boundary Width Control: The knob that adjusts the width of the warning and static correction zones.
Note: Adjusting the knob does not change the level of static correction on the receiver collar.
Receiver Collar
Fence Transmitter
premierpet.com 5
Locate the Fence Transmitter
3 ft.
10 Twists/f t.
• Place the fence transmitter:
• In a dry, well ventilated, protected area (1A, 1B).
• In an area where temperatures do not fall below -10°F (-23°C) or above 140°F (40°C) (e.g., garage,
basement, shed, closet).
• Secured to a stationary surface using appropriate mounting hardware (not included). A mounting
template is included in the back of this guide.
• At least 3 ft. from large metal objects or appliances as these items may inter fere with the signal
consistency (1C).
Once you have mounted the fence transmitter, the boundary wire must exit the building. This can be
accomplished via a window or through a hole drilled through the wall. Ensure the drill path is clear of any
utilities. Make sure the boundary wire is not cut o or pinched by a window, door, or garage door, as this
can damage it over time.
To prevent fires and electrical hazards, install the fence transmitter in building s that are in accordance
with state and local electrical codes.
1A 1B
1C
Lay Out the System
Basic Planning Tips
Underg round cables ca n carry high v oltage. Have all und erground cab les marked bef ore you dig to bur y your wire. In
most ar eas this is a fre e service. Avoi d these cable s when you dig.
For information regarding how these underground wires can aect your system’s operation, see
“Position the Boundary Wire”.
• The boundary wire MUST start at the fence transmitter and make
a continuous loop back (2A).
• Twisting the boundar y wire cancels the signal and allows your pet
to cross over that area without correction. Plastic or metal piping
will not cancel the signal. Twist the boundar y wire 10-12 times per
ft. to cancel the signal (2A).
• Design a layout that is suitable for your yard (sample layouts are
provided in this section).
• Always use gradual turns at the corners with a minimum of 3 ft.
radius to produce a more consistent boundary (2B). Do not use
sharp turns, as this will cause gaps in your boundary.
• To properly contain your pet, we recommend setting a boundary
width for the warning and static correction zones to approximately
12-20 ft. (6-10 ft. on each side of the wire).
• Avoid making pass ageways too narrow for your pet to move about
freely (e.g., along the sides of a house).
• The receiver collar can be activated inside the house if the boundary
wire runs along the outside wall of the house. If this occurs, remove your
pet’s receiver collar before bringing him inside, decrease the range using
the boundary width control knob or consider an alternative layout.
2A
2B
+1 (866) 381-27856
Sample Layouts
D
E
A
C
B
Sample 1: Perimeter Loop (Single Loop)
The perimeter loop is the most common layout. This will allow your pet to
freely and safely roam your entire proper ty (2C). It can also protect gardens,
pools and landscaping (2D).
2D
2C
Sample 2 (2E): Perimeter Loop Using Existing Fence (Single Loop)
This layout allows you to include your existing fence as part of your layout
and keep your pet from jumping out or digging under your existing fence. It
reduces the amount of wire which will need to be buried. From the fence
transmitter, run the wire to A, A to B, B to C, C to D, D to E, E to A, twist the
wires from A back to the fence transmitter. See the “Install the Boundary
Wire” section for more information on at taching the wire to a fence.
premierpet.com 7
2E
Double Loop
E
F
B
A
D
C
E
F
C
A
D
B
5 ft.
5 ft.
B
A
5 ft.
E
B
D
C
A
5 ft.
E
F
B
A
D
C
5 ft.
90°
Boundary
Wire
Buried Cable
10 ft.
10 ft.
A double loop must be used when you are not establishing the boundary zone on all sides of your proper ty.
When using a double loop, the boundary wire must be separated by a minimum of 5 ft. to avoid
canceling the signal. Remember that a double loop will require twice as much wire.
Sample 3 (2F): Front or Back Yard Only (Double Loop)
From the fence transmitter, run the wire to A, A to B, B to C, C to D,
D to E, E to F, make a U-turn and follow your path all the way back to A,
keeping the wire separated at least 5 ft. Twist the wire from A back to the
fence transmitter.
Sample 4 (2G): Front Boundary Only (Double Loop)
From the fence transmitter, run the wire to A, A to B, B back to A keeping
the wire separated at least 5 ft. Twist the wire from A back to the
fence transmitter.
2F
2G
Sample 5 (2H): Lake Acce ss (Double Loop)
From the fence transmitter, run the wire to A, A to B, make a U-turn and go
2H
to C, C to D, D to E, make a U-turn and follow your path all the way back to
A keeping wire separated at least 5 ft. Twist the wire from A back to the
fence transmitter.
Sample 6 (2J): Wire Loop Attached to Existing Fence (Double Loop)
This layout allows you to include your existing fence as part of your layout
2J
and keep your pet from jumping out or digging under your existing fence. It
reduces the amount of wire which will need to be buried. Run the wire from
the fence transmit ter to A, A to B, B to C, C to D, D to E, E to F, make a U-turn
and follow your path all the way back to A, keeping the wire separated at
least 5 f t. Twist the wire from A back to the fence transmitter. See the “Install
the Boundary Wire” section for more information on attaching the wire to
a fence.
Position the Boundary Wire
Lay out the boundary wire using your planned boundary and test the
system BEFORE bur ying the wire or attaching it to an existing fence. This
will make any layout changes easier. Work carefully. A nick in the wire
insulation can diminish the signal strength and create a weak area where
your pet can escape.
Running the boundary wire parallel to and within 10 ft. of electrical wires,
neighboring containment systems, telephone wires, television or antenna
cables, or satellite dishes may cause an inconsistent signal. If you must
cross any of these, do so at 90-degree angles (perpendicularly) (3A).
If separating your boundary wire by at least 10 ft. from a neighboring containment system’s wire does not
reduce the inconsistent signal, contact the Customer Care Center.
+1 (866) 381-27858
3A
To Twist the Boundary Wire
10 Twists/ft.
TWISTED WIRES
1
2
3/8 in. 3/8 in.
Twisting the boundar y wire cancels the signal and allows your pet to cross
over that area safely (3B). The signal cannot be canceled by running the wire
through plastic or metal piping. Using shielded cable in place of the boundar y
wire will also not cancel the signal. Refer to figure (3C) for the correct method
of twisting the w ire. You can twist your own wire by cutting 2 equal leng ths of
boundary wire supplied and twisting them together. Anchor one end of the
wires to something secure and insert the other end in a power drill. Pull the
wire taut. The drill enables you to twis t the wire quickly. Twist the boundary
wire 10 to 12 times per ft. to cancel the signal. Once you have completed your
boundary layout, insert the t wisted wire into the transmitter.
To Splice or Repair the Boundary Wire
If you need additional boundary wire to expand your wire loop, you will
need to splice the wires together. Note the locations of all splices for
future reference.
Strip approximately 3/8 in. of insulation o the ends of the boundary wires to
be spliced (3D). Make sure the copper boundary wire is not corroded. If the
boundary wire is corroded, cut it back to expose clean copper wire.
Insert the stripped ends into the wire nut and twist the wire nut around the
wires. Ensure that there is no copper exposed beyond the end of the wire nut.
Tie a knot 3 to 4 in. from the wire nut (3E). Ensure that the wire nut is secure on
the wire splice.
Once you have securely spliced the wires together, open the lid of the gelfilled splice capsule and inser t the wire nut as deeply as possible into the
waterproof gel inside the capsule (3F). Snap the lid of the capsule shut (3G).
For proper system performance, the splice connection must be waterproof.
If your splice pulls loose, the entire system will fail. Make sure your splice
is secure. Additional gel-filled splice capsules and wire nuts are available
through the Customer Care Center.
3E 3F 3G
3B
3C
CORRECT
INCORRECT
3D
BOUNDARY WIRE
WATERPROOF SPLICE
Additional Boundary Wire
Extra direct burial boundar y wire can be purchased in 500 f t. spools
at the store w here you purchased the kit or through the Customer
Care Center.
Note: When adding boundary wire, it must act as a continuous loop.
The table at right indicates the approximate length of boundar y wire
needed for a square Single Loop layout. Length will vary due to the
amount of t wisted wire and layout used.
Acres Feet of Wire Needed
1/4
1/3
1/2
1
2
5
415
480
590
835
1180
1870
Connect the Wires to the Surge Protector and Fence Transmitter
Surge Protection
Lightning strikes that occur even several miles away from your installation can create power surges or
spikes which may damage your unprotected electronic pet containment sys tem. The surge protector
included with this system is designed to protect your In-Ground Fence™ system from surges or spikes that
can reach it via your AC power connection and/or your buried boundar y wire.
premierpet.com 9
Install the Surge Protector & Connect the Wires (4A)
LP-4100
Loop
Transmitter
Boundary Wire
Loop
Boundary Wires
(Twisted)
Red Loop Tabs
Transmitter
Wires
(Twisted)
Black
Transmitter
Tab s
Boundary
Wire
Terminals
Power
Adapter
Power
Jack
Fence
Transmitter
Push Tab
Down
Insert bare end
of wire into
opened slot
and release tab
to lock.
• Do no t install, conn ect, or remov e your system d uring a lightni ng storm. If the s torm is close en ough for you to hea r
thunde r, it is clos e enough to create h azardous su rges.
• Turn o powe r to outlet befor e you install or r emove your sur ge protector.
• Risk o f electrical s hock or fire. Use s urge protecto r only with a duple x outlet with cente r screw. Attach uni t with
long scr ew supplied.
• Risk o f electric sho ck. Use the fen ce transmitt er and surge prote ctor indoor s in dry locatio n only.
• Do no t install the sur ge protector i f there is not at leas t 30 ft. (10 m) or more of wi re between th e electrical o utlet and
electrical service panel.
• If po ssible, DO NOT use a n AC circuit prote cted with a GFCI (g round fault circu it interrupte r). In rare cas es, nearby
lightni ng strikes may ca use the GFCI to trip . Without powe r your dog may be vu lnerable to esc ape. You will have to
reset t he GFCI to restore p ower to the sys tem.
• Plug th e surge protec tor into a grounde d (3-prong) outle t that is within 5 f t. of the fence tra nsmitter. ALWAYS use a
grounded (3-prong) ou tlet to ensure maximum protection.
• Do no t remove the gro und prong fro m the surge protec tor plug. Do not us e a 3-prong plug to 2-p rong outlet co nverter.
Doing s o will make the sur ge protector in eective ag ainst surges o r spikes.
1. Turn the power OFF to the outlet
that the surge protector and fence
4A
transmitter will be plugged into.
2. We recommend that, if possible, use
the outlet center screw that holds the
cover plate in place to secure the surge
protector to the outlet. To do this, tape
the top of the cover plate to the wall,
then remove the cover plate center
screw. Plug the surge protector into the
lower outlet and then secure the cover
plate using the longer screw included
with the protector. The screw is for
mechanical attachment only and does
not ground the protector. Remove the
tape and turn ON the power to the outlet.
4B
3. Run the boundar y wire through a window, under a door, through a crawl
space vent, or any other appropriate available access. You can also drill a
hole through your wall.
4. Strip 3⁄8 in. of insulation from the ends of the boundary wire. Insert
the stripped ends into the 2 left red connector holes on the bottom of
the surge protector labeled “Loop” (4B). There should be 1 wire in each
connector hole. Press the plastic tab, insert the wires and release the tab.
Make sure the wires do not touch each other at the terminals.
Verify t hat the boundar y loop and tran smitter wire s connect to the p roper surge
protec tor terminals . Reversed co nnections w ill result in an in creased ri sk of surge
related damage.
5. Determine the length of wire needed to pa ss from the surge protector to the fence transmitter.
Measure and cut 2 lengths of wire, then strip 3⁄8 in. of insulation at both ends. Twist the 2 lengths
together, with at least 10-12 twists per ft., so the wires will not send out a signal.
6. Insert the ends of the twisted transmitter wires into the right 2 black connectors at the bottom of the
surge protector labeled “Transmitter”.
7. Press the red plas tic tabs on the fence transmitter and insert the opposite ends of the twisted wire
into the boundary wire terminals.
8. Turn the boundary width control knob to 10. This will set the boundary width at the maximum width.
9. Plug in the transmitter power adapter to the outlet on the front of the surge protector.
10. The power light and loop indicator lights should come on. If this does not happen, see the
“Troubleshooting” section.
For adde d protection , when unused f or long perio ds of time or prio r to thunderst orms, unplug f rom the wall out let and
discon nect the loop b oundary wir es. This will p revent damag e to the transmit ter due to surges .
+1 (866) 381-278510
Prepare the Receiver Collar
Your receiver collar comes with short contact points installed. Use the long
contact points for pets with long or thick hair. Tighten the contact point s
using the test light tool (5A) one-half turn beyond finger tight. Check the
tightness weekly.
To Insert and Remove the Receiver Collar Battery
Do not ins tall the batter y while the rece iver collar is on y our pet.
This receiver collar utilizes a replaceable Premier Pet™ batter y (GAC11-16351).
This unique battery is designed to make battery replacement ea sier and
increase water protection.
To insert the bat tery, align the symbols on the battery (arrow) and receiver
collar (triangle) (5B). Use the edge of the test light tool (5A) to turn the
batter y clockwise until the arrow lines up with the lock symbol on the
housing.
To remove the batter y, turn the battery counter-clock wise using
the edge of the test light tool (5B). DO NOT attempt to cut into or pry open
the battery. Be sure to discard the used bat tery properly. Battery life will
vary depending on how of ten your pet tests the sys tem and receives a static
correction. Check the receiver collar every month to ensure the battery is
working properly.
If the receiver LED indicator light is flashing every 4 to 5 seconds, battery
replacement is required. Remove the old battery from the receiver collar.
Discharge all power by holding the correction level button down until the LED
is no longer illuminated. Replace with a new battery.
A replacement Premier Pet
retailers. Contac t the Customer Care Center or visit our web site at ww w.
premierpet.com to locate a retailer near you.
™
batter y (GAC11-16351) can be found at many
To Set the Static Correction Level
Read all steps before attempting to set the static correction Level.
1. Remove the clear plastic cover with the test light tool to expose the
correction level button (5C).
2. With the batter y installed, press the correction level button and release
when the receiver indicator light lights up (5D).
3. The receiver indicator light w ill emit a series of flashes representing the
static correction Level.
4. Increase the static correction Level by pressing and relea sing the
correction level button within 5 seconds of the previous series of flashes.
5. After setting the static correction Level, replace the cover to protect the
correction level button.
The static correction levels increase in strength from 1 to 5. Pushing the
correction level button while the receiver collar is on level 5 will cause the
receiver collar to revert to Level 1. Refer to the Function and Response Table to
choose the static correction level that best fits your pet.
The receiver collar is equipped to automatically increase the level of static
correction the longer your pet remains in the static correction zone if the collar
is set at level 2 or above.
The receiver LED indicator light acts as a low batter y indicator, flashing every 4 to 5 seconds when
replacement is required.
5A
5B
5C
5D
Static Correction Level Table
Static Correction
Level
1 1 Flash No Static Correction, Tone Only
2 2 Flashes Low Static Correction
3 3 Flashes Medium Static Correction
4 4 Flashes Medium High Static Correction
5 5 Flashes High Static Correction
Indicator Light Response Receiver Collar Function
Flashes once every 4 to 5 seconds Indicates Low Battery
premierpet.com 11
Anti-Linger Prevention
Boundary
Wire
The anti-linger prevention feature keeps your dog from staying in the warning zone for long periods of
time and draining the receiver collar battery. Your dog will hear a warning tone when he reaches the
warning zone. If your dog does not return to the pet area after 2 seconds, he will receive a continuous
static correction until he returns to the pet area.
Run Through Prevention
This system includes a unique “run-through” prevention so that your dog cannot escape the pet area
without receiving an increased level of static correc tion. The receiver collar automatically increases the
static correction when your dog continues more than 20% of the way through the pet fencing boundar y
width. For example, if the signal is detected 10 ft. from the wire and your dog enters the static correc tion
zone, this feature is activated when he is approximately 8 f t. from the boundary wire. Your dog will
then receive a static correction that is at an increased level corresponding to the static correction level
setting on the receiver collar. The receiver collar is equipped to automatically increase the level of static
correction the longer your pet remains in the static correction zone if the collar is set at level 2 or above.
The run through prevention sound is an intermittent tone.
Over Correction Protection
In the unlikely event that your pet “freezes” in the static correction zone, this feature limits the static
correction duration to a maximum of 30 seconds. While the system locks out further static correction,
the warning tone will continue until the pet leaves the static correction zone.
Set the Boundary Width and Test the Receiver Collar
With the boundar y wire in place and properly connected, it is time to set the pet boundary width and test
the system.
The rece iver collar sho uld NOT be on your dog w hen the syste m is tested.
Note: The receiver collar is waterproof, which can make the tone hard to hear.
The flashing test light when held to the contact points indicates the receiver
collar is delivering static correction. To best utilize the automatic run-through
prevention feature, the containment boundar y width should ex tend at least 6
to 10 ft. on each side of the boundar y wire (total boundary width of 12 to 20 ft.).
1. Apply power to the fence transmitter with the supplied power adapter.
2. The boundar y width is adjusted using the transmitter’s boundar y width
control knob. Turn the knob counter clockwise until the loop indicator
light is no longer lit. Turn the knob clockwise and increase by 2 numbers.
The light should turn ON.
The rece iver collar sho uld not be on your d og when the sy stem is tested . Your pet
may recei ve an unintende d correcti on.
3. Place battery in receiver collar. To identif y the warning and static
correction zones make sure the receiver collar is set at level 5.
4. Test the boundary width of the system by selecting a section of straight
boundary wire that is at leas t 50 ft. long. Start inside the center of the
containment field.
5. Place the test light tool contacts on the contact points on the receiver
collar (6A). Hold the receiver collar at your dog’s neck height with the
contact points pointing up (6B) and the correction level but ton facing the
boundary wire. Slowly walk toward the boundar y wire until you hear the
warning tone (6C). When you hear the warning tone, you have identified
the boundary width distance (static correction zone). 2 s econds after the
warning tone, the test light will begin to flash. This flashing light can aid
you in identifying the boundar y width should you have diculty hearing
the tone. To avoid having the receiver collar go into over correction
protection mode, walk back into the pet area until the toning stops. If the
receiver collar does not tone at the desired range, adjust the boundary
width control knob to obtain the desired range.
6A
6B
6C
+1 (866) 381-278512
Turning the boundary width control knob clockwise increases the
Boundary
Wire
DOUBLE LOOP
SINGLE LOOP
5' 5'
boundary width while turning it counterclockwise decreases it (6D).
6D
Repeat this activity as needed until the receiver collar tones between 6 to
10 ft. from the boundary wire. If using a double loop layout, you may need
to increase the separation of the boundary wire and/or increase the size
of the boundary width to achieve the desired range.
6. Test in a number of dierent locations around the containment area until
you are satisfied that the system is functioning properly.
7. Next, walk all around the pet area to ensure there are no areas where
the receiver collar may activate from signals coupled onto buried wires
or cables. Test the collar in and around the inside of the house as well.
As mentioned, cable and wires from cable TV, electrical or telephone
lines may conduct pet fencing signals inside and outside the house that
can activate the dog’s collar accidentally. While rare, if this occurs your
boundary wire is probably too close to these outside lines and should be
6E
moved or modified a s shown in Figure 3A.
8. To test the run-through prevention feature, walk towards the boundary
wire. The receiver collar should tone and the test light should flash
brighter as you enter the run-through area (6E). If you are satisfied that
your system is functioning properly, you are ready to star t bur ying the
boundary wire. If the receiver collar did not tone or the test light did not
flash, see the “Troubleshooting” section.
Install the Boundary Wire
To Bury the Boundary Wire
Before y ou begin inst alling the boun dary wire, un plug the fence tra nsmitter pow er adapter from th e outlet.
Burying the boundar y wire is recommended to protect it and prevent disabling the system.
1. Cut a trench 1–3 in. deep along your planned boundary.
2. Place the boundary wire into the trench maintaining some slack to allow
it to expand and contract with temperature variations.
3. Use a blunt tool such as a wooden paint stick to push the boundary wire
into the trench. Be careful not to damage the boundary wire.
To Attach the Boundary Wire to an Existing Fence
The boundary wire of the Premier Pet™ In-Ground Fence™ system can be
attached to a chain link fence, split rail fence, or a wooden privac y fence.
The boundary wire can be attached as high a s needed. However, make sure
the boundary width is set at a high enough range for the pet to receive the
signal. If using a double loop with an existing fence at least 5 ft. tall, run the
boundary wire on top of the fence and return it on the bottom of the fence to
get the 3 to 5 ft. separation needed.
• Chain Link Fence (7A): Weave boundary wire through the links or use
plastic quick ties.
• Wooden Split Rail or Privacy Fence (7A): Use staples to attach boundar y
wire. Avoid puncturing the insulation of the boundary wire.
• Double Loop with an Existing Fence: Run the boundary wire on top
of the fence and return it on the bottom of the fence to get the 3 to 5 f t.
separation needed.
• Gate (Single Loop) (7B): Bury the boundary wire in the ground across the
gate opening. Note: The signal is still active across the gate. Your pet cannot
pass through an open gate.
• Gate (Double Loop) (7B): Bury both boundar y wires across the gate
opening while keeping them at least 5 ft. apart.
7A
7B
premierpet.com 13
To Cross Hard Surfaces (driveways, sidewalks, etc.)
Follow all s afety instr uctions for y our power tool s. Be sure to alway s wear your safet y goggles.
• Concrete Driveway or Sidewalk (7C): Place the boundary wire in a convenient expansion joint or create
a groove using a circular saw and masonr y blade. Place the boundary wire in the groove and cover
with an appropriate waterproofing compound. For best results, brush away dirt or other debris before
patching.
• Gravel or Dirt Driveway (7D): Place the boundary wire in a PVC pipe or water hose to protect the
boundary wire before burying
7C 7D
Place the Boundary Flags
The boundary flags are visual reminders for your pet of where the warning zone is located.
1. Place the test light contacts on the contact points and hold the receiver collar at your pet’s neck height.
2. Walk towards the warning zone until the receiver collar beeps (8A).
3. Place a boundary flag in the ground (8B).
4. Walk back into the pet area until the beeping stops.
5. Repeat this process around the warning zone until it is marked with boundary flags every 10 ft.
Note: If you cannot hear the beep, see the test light instructions.
To prevent an uni ntended corre ction, after t he boundar y flags have bee n placed, be sure to s et the static cor rection on th e
receiv er collar back to leve l 1 Ton e only.
8A 8B
Fit the Receiver Collar
Important: The proper fit and placement of your receiver collar is important for eective training.
The contact points must have direct contact with your pet’s skin on the underside of his neck.
Please r ead and follow th e instruct ions in this man ual. Proper fit of t he collar is imp ortant. A coll ar worn for too lo ng
or made to o tight on the pet ’s neck may cause sk in damage. Rang ing from redn ess to press ure ulcers; thi s condition is
commo nly known as be d sores.
To assure a proper fit, please follow these steps:
1. Make sure that the batter y is not installed in the receiver collar.
2. Start with your pet standing comfortably.
3. Place the receiver collar on your pet so that the Premier Pet
+1 (866) 381-278514
™
logo is facing your pet’s chin.
4. Center the contact point s underneath your pet’s neck, touching the skin. If your pet has a long or thick
Ridges
Slide Buckle
Fasten Buckle
Ridges
Slide Buckle
Fasten Buckle
coat, use the enclosed long contact point s to reach through the hair. Note: It is sometimes necessary
to trim the hair around the contac t points to make sure that contact is consistent.
5. The receiver collar should fit snugly, yet loose enough to
allow one finger to fit between a contact point and your
pet’s neck (9A).
6. Allow your pet to wear the collar for several minutes then
recheck the fit. Check the fit again as your pet becomes
more comfortable with the receiver collar.
7. Once you are s atisfied with the fit of the receiver collar,
then you may trim any excess collar s trap as follows (9B):
A. Mark the desired length of the receiver collar with a
pen. Allow for growth if your pet is young or grows a
thick winter coat.
B. Remove the receiver collar from your pet and cut o
the excess.
C. Before placing the receiver collar back onto your pet,
seal the edge of the cut collar by applying a flame
along the frayed edge.
9A
9B
To Re-Thread the Collar
The Slide Buckle prevents the collar from
becoming loose around your pet’s neck.
Ridges
The Ridges must be facing up; the collar will slip if it
is not properly threaded.
Slide Buckle
Fasten Buckle
To loosen: Slide the strap through the Slide and
Fasten Buckles and pull down.
To tighten: Slide the strap up through the Fas ten
Buckle and pull through the Slide Buckle.
premierpet.com 15
Training Guide
• Proper training of your pet is essential to the success of the system.
• Remove the collar after each training session.
• Be sure to place the collar on your dog’s neck with the Premier Pet
• If your pet shows signs of stress, slow down the training schedule, add additional days of training or
increase the amount of play time with your pet in the pet area. Common stress signals include the pet
pulling on the leash toward the house, ears tucked or pulled back, tail down or tucked between legs,
body lowered, nervous/frantic movement or stiening of the pet’s body, lip-licking or yawning.
Day 1
For the first day, start with the collar set to level 1, tone-only. With your pet on a leash and his favorite treat s
on hand, allow him to explore the pet area. Let him cross the boundar y and hear the tone from the collar,
then ask him to come back into the pet area and reward him. Aim to teach your dog that being inside the
pet area is rewarding, while being out side it is not. Keep your mood upbeat as dogs can understand when
you are happy or upset. Do 2 or 3 training sessions for about 10-15 minutes each. Do not tr y to do too much
too quickly. More frequent shor t sessions are better than less frequent, longer sessions.
Days 2–4
On days 2 through 4, repeat this process but with the collar set to level 2: the mildest level of static
correction. Observe whether or not your dog responds to the shock. Indicators of a response are looking
around in curiosity, flicking his ears or scratching at the collar. If he does not respond, check the collar fit
to make sure the contact points are making contact with his skin. If it fits correctly and your dog does not
respond, move up to the next level and repeat the process. Do 2 or 3 training sessions for about 10-15
minutes each.
Days 5–8
On days 5 through 8, continue where you left o on day 4, but now add in some staged distractions. The
goal is to have your pet stay within the boundary even with these new temptations. Start with lower value
temptations and work your way up. Some examples are:
• Have a family member cross from inside the boundary out of it.
• Place a toy out side the boundary.
• Have a friend or neighbor walk another pet outside the boundar y area.
• Remember, it is impor tant to keep your pet on a leash throughout this process while he is still learning
the boundary. Also, never coax your pet to leave the pet area.
™
logo facing up.
Days 9–30
Once your pet consistently avoids the boundar y regardless of dis tractions or temptations, he is ready for
the next step: unlea shed supervision. Stay close by with a leash at hand. Play with your pet for a while
during the first few sessions. If your dog does not tr y to leave the boundar y, occupy yourself with another
task in the yard, and allow him to freely explore. Continue watching your pet. If he escapes, remove
the receiver collar and lead him back into the pet area. Start these sessions at about 15 minutes and
gradually work up to an hour or more.
When your pet proves trust worthy, you can let him out on his own. Continue to check on him regularly.
You can remove every other boundary fla g every 4 days until all the flag s are removed. Save them in case
you move or need to train another pet.
+1 (866) 381-278516
TROUBLESHOOTING
The receive r collar is not
beeping or correcting.
The receiver collar is beeping,
but the pe t is not respond ing
to the static correction.
The receive r collar has to be
held on top of t he boundary
wire to act ivate.
The receiver collar activates
inside the house.
The receive r LED indicator
light is flas hing every 4 to
5 seconds an d I have just
installed a n ew battery.
I have an inconsis tent signal.
The power an d loop indicator
lights are o .
• Check battery to make sure it is installed properly.
• Check that both lights are lit on the fence transmitter. If not, perform
the “System Test.”
• Test the receiver collar with the test light walking toward the
boundary wire.
• If the test light flashes, check the fit of the receiver collar.
• Trim your pet’s fur where the contact points touch the neck and/or
switch to the longer contact points.
• Increase static correction level.
• Repeat training steps to reinforce training.
• Purchase a stronger receiver collar by contacting the Customer
Care Center.
• Replace battery.
• Adjust boundar y width control knob clock wise to increase the
distance from the boundary wire that the receiver collar activates.
• If using a double loop, make sure boundary wires are separated at
least 5 f t.
• If the receiver collar still has to be held on top of the boundary wire,
perform the “System Test.”
• Turn the boundary width control knob counterclockwise to decrease
the distance from the boundary wire that the receiver collar activates.
• Make sure the boundary wire is not running too close to the house.
The signal can transmit through the walls of your house.
• Make sure boundar y wires are twisted from Boundary to the
fence transmitter.
• To reset the low battery indicator, remove the batter y from the
receiver collar. Discharge all power by holding the correction level
button down until the LED is no longer illuminated. Reins tall battery.
• Make sure fence transmitter is at least 3 ft. from large metal objects
or appliances.
• Make sure all boundar y wire turns are gradual with a minimum
3-ft. radius.
• Make sure the boundary wire is not running parallel to and within
10 ft. of electrical wires, neighboring containment systems, telephone
wires, television or antenna cables, or satellite dishes.
• If a neighboring containment system may be causing an inconsistent
signal, move the boundar y wire farther away from the neighboring
containment system.
• Check that the power adapter is plug ged into the fence transmitter.
• Check that the power adapter is plug ged in properly.
• If the system is plug ged into a GFCI or RCD outlet, check to see if the
circuit ha s been tripped. Reset the GFCI or RCD circuit if required.
• Verify that the outlet is working properly by plugging in a known
working item such a s a radio.
• Try plugging into another 120-volt outlet.
• If the lights still do not come on, the fence transmitter and/or power
adapter needs to be replaced. Contact the Customer Care Center.
• If a surge protector is installed, unplug the surge protector and plug
the power adapter directly into the outlet. If the transmitter operates
without the surge protector, contact the Customer Care Center for a
replacement surge protector.
premierpet.com 17
TROUBLESHOOTING
The power ligh t is on, the
loop indic ator light is o.
• Check boundar y wire connections at the fence transmitter for
proper connection.
• Check for broken or damaged boundary wires at outside entry to the house.
• Perform the system test to determine if the fence transmitter or
surge protector needs to be replaced.
• If the fence transmitter is functioning properly, you have a break in
your boundary wire. See the “Wire Break Location Test” section in
this guide.
Additional Information
• Test the receiver collar at least once a month to verify that it is functioning properly. Check that it
activates at the boundary wire. Battery life depends upon how often the receiver collar is activated.
• Remove the receiver collar from your pet when indoors for the comfort of your pet.
System Test
The system test is used to determine the cause of system problems that have not been addressed
elsewhere in this guide. You will need a piece of boundary wire greater than 15 ft. long with 3⁄8 in. of
insulation removed from each end to use as a test loop w ire. Make a note of your boundary width control
knob setting, and receiver collar setting before beginning the system test. Follow the s teps below to
perform the system tes t:
1. Remove the receiver collar from your dog and make sure a good battery is
installed in the receiver.
2. Set the receiver collar static correc tion Level to 5.
3. Disconnect the twis ted boundary wire from the boundary wire terminals
on the fence transmitter by pressing the red release levers on the
connector and pulling the wires free (11A).
4. Insert the 2 ends of the test loop wire into the boundary wire Terminals on
the transmitter.
5. Turn the boundar y width control knob to 10 and then back to 5.
6. Place the test light tool contacts on the contact points of the receiver collar.
While holding the receiver collar with the test light tool in place, approach
the wire from the outside loop 2 in. o the ground. Make a mental note of the
distance where the receiver collar activates from the wire.
7. Turn the boundar y width control knob to 10 and repeat Step 6. The
distance where the receiver collar activates should be greater than the
previous result.
8. If more than one receiver collar is used on the system, repeat the above
test on each collar.
9. Interpreting the Results:
A. If the power light or the loop indicator light are not both lit on the
fence transmitter for any of the above tests, there is a problem with
the transmitter. Contact the Customer Care Center.
B. If both the power and loop indicator lights are on, but the receiver
collar does not activate on the test loop wire, the receiver collar is not
working. Contac t the Customer Care Center.
C. If the transmitter power and loop indicator lights are on and the
receiver collar is activating at dierent distances on the test loop wire,
the problem is most likely in the containment boundary wire or surge
protector. Reconnect the transmitter wires to the surge protector and
connect the Test Loop to the surge protector loop terminals. Repeat
steps (5-8) (11B).
10. Interpreting the Results with the surge protector:
A. If both the power and loop indicator lights are ON and the receiver collar is activating at dierent
distances on the test loop wire, the problem is in the containment boundary wire. Per form the
Wire Break Location Test.
B. If the Loop indicator light is OFF there is a problem with the surge protector. Contact the
Customer Care Center.
11A
System Test Surg e
Protector Unconnected
11B
System Test Surg e
Protector Connected
+1 (866) 381-278518
11. When testing is complete reconnect and verify that the boundar y wire is plugged into the Loop
Test
Wire
Terminals on the surge protector and the transmitter is connected to the surge protector.
12. Return the boundary width control knob setting to the position noted earlier.
13. Repeat the boundar y width testing from Step 6 on Page 16 until you achieve the desired boundar y
width between 12 to 20 ft.
Wire Break Location Test
The following lists identify the common locations where wire breaks occur. Please inspect these areas
for signs of damage. Wire breaks in the twisted pair are commonly found:
1. At the wire exit point of the house
2. Where the twisted pair of wire enters the ground from the house, usually caused by string trimmers
3. Where the wires cross sidewalks or driveways due to edging and string trimmers
4. Around landscaping and flower beds due to digging or working up the soil
Wire breaks in the boundar y wire are commonly found:
1. In aerated lawns
2. Where the wires cross sidewalks or driveways due to edging and string trimmers
3. Around landscaping and flower beds due to digging or working up the soil
4. At wire splices where Gel-filled capsules have not been installed
5. At wire splices without reinforcements knots (refer to Figure 3E)
If you still cannot find the break in the boundary wire, there are 2 options for locating it:
Option 1: It is recommended to contact the Customer Care Center to purchase a Wire Break Locator
(R FA -5 90).
Option 2: Follow the procedure below:
1. Unplug the fence transmitter.
2. Connect both ends of your twisted boundary wire to one Loop Terminal
on the surge protector.
3. Measure and cut a Test Wire which is half the length of your total
boundary wire footage.
4. Connect one end of Test Wire to the other Loop Terminal on the
surge protector.
5. Locate the half way point of your boundary and cut the boundary wire.
6. Splice the other end of the Test Wire to either side of your boundary wire
where you cut it in half.
7. Plug in the fence transmitter and check the loop indicator light. If the
loop indicator light is ON, you can assume the break is in the other half of
the boundary wire.
8. If the loop indicator light did not come on, you may assume there is a break in this por tion of the
boundary wire. However, there is a small chance of having more than one break in your system. Be
sure to check both halves of your entire loop.
9. Replace the damaged boundar y wire with new boundar y wire.
10. Reconnect the boundar y wire to the surge protector.
11. Check the loop indicator light. If the loop indicator light is ON, test the system with the receiver collar.
premierpet.com 19
Terms of Use and Limitation of Liability
1. Terms of Use
This Product is oered to you conditioned upon your acceptance without modification of the terms,
conditions and notices contained herein. Usage of this Product implies acceptance of all such terms,
conditions, and notices.
2. Proper Use
This Product is designed for use with pets w here training is desired. The specific temperament of
your pet may not work with this Product. If you are unsure whether this is appropriate for your pet,
please consult your veterinarian or cer tified trainer.
3. No Unlawful or Prohibited Use
This Product is designed for use with pets only. This pet training device is not intended to harm, injure
or provoke. Using this Product in a way that is not intended could result in violation of Federal, State
or local laws.
4. Limitation of Liability
In no event shall Radio Systems Corporation be liable for any direct, indirect, punitive, incidental,
special or consequential damages, or any damages whatsoever arising out of or connected with the
use or misuse of this Product. Buyer a ssumes all risks and liability from the use of this Product.
5. Modification of Terms and Conditions
Radio Systems Corporation reserves the right to change the terms, conditions and notices under
which this Product is oered.
Warranty
One Year Non-Transferrable Limited Warranty
This Product has the benefit of a limited manufac turer’s warranty. Complete details of the warranty
applicable to this Product and its terms can be found at premierpet.com.
+1 (866) 381-278520
Perchlorate Battery
Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.
Battery Disposal
Separate collection of spent batteries is required in many regions; check the regulations in your
area before discarding spent batteries. The collar receiver operates on a 6-volt lithium coin cell
batter y. Replace only with equivalent battery available from the Customer Care Center. For a
listing of Customer Care Center telephone numbers in your area, visit www.premierpet.com.
Compliance
FCC
This device complies with part 15 of the FCC Rules. Operation is subjec t to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tes ted and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a specific installation. If interference does occur to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connec t the equipment to an outlet on a circuit dierent from that to which the receiver is connected.
• Consult customer care, the dealer, or an experienced radio/T V technician for help.
CAUTION: Mo dification or cha nges to this equi pment not exp ressly approve d by Radio Systems Cor poration may
void the us er’s authorit y to operate the eq uipment.
For a list of patents protecting this product,
please visit: http://w ww.radiosystemscorporation.com/patents
premierpet.com 21
Layout Grid
+1 (866) 381-278522
Mounting Template
Drill
Here
3.000 in.
(7.62 cm)
Drill
Here
premierpet.com 23
Loading...