Premier Mounts EST150 User Manual

INSTALLATION INSTRUCTIONS

Single-Stud Short-Throw Projector Wall Mount

Model: EST150

NORTH AMERICA

3130 East Miraloma Avenue

Anaheim, CA 92806 USA

USA and Canada

Phone: [phone]

Fax: [phone]

Other Locations

Phone: [phone]

Fax: [phone]

Unit 3, The Moorings Business Park, Channel Way

Longford, Coventry, CV6 6RH, UK

9530-011-021-01

EUROPE

Phone: [phone]

Fax: [phone]

EST150

Table of Contents

Heading 1

Weight Capacity 2

Warning Statements 2
Installation Tools 3
Parts List 3
Features 4
Determining the Installation Height 5
Wood Stud Installation 6
Throw Distance Calculation 8

Projector Installation 8

Attaching the Mount Carriage 9
Multiple Mounting Point Installation 10
Single Mounting Point Installation 12

Attaching the Mount Carriage to the Projector Arm 13

Cable Routing (Optional) 14

Securing the Projector (Optional) 14
Mount Adjustment 15
Technical Specications 15
Warranty 16

Disclaimer 16

Weight Capacity

Maximum projector weight:

Warning Statements

PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UN­DERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP
THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.

PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR
PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR
MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION
OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR
MODIFICATIONS.

SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER
SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.

At least two qualied people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the
projector.

If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud nder is

recommended.

Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires in
wall. Cutting/drilling into an electrical line may cause serious injury.

Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe water
damage to the mounting surface.

25 lbs.

THE WALL STRUCTURE MUST BE CAPABLE OF HOLDING FIVE
(5) TIMES THE WEIGHT OF THE PROJECTOR. IF NOT, THEN THE
WALL STRUCTURE MUST BE REINFORCED.

This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact

Contact Premier Mounts with any questions

[phone]
[e-mail]

Page 2 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions

EST150

Installation Tools

The following tools may be required depending upon your particular installation. They are not included.

Electronic Stud Finder

Level

Phillips Screwdriver

⅛˝ Drill Bit

Drill

Parts List

Make sure your Premier Mounts product has the following hardware and components before beginning installation. If

there are parts missing and/or damaged, stop the installation and call Premier Mounts at [phone].

EST150 Hardware

Projector Arm

(Qty 1)

Projector Arm

Cover Plate (Qty 1)

Mount Carriage

(Qty 1)

M3 Flat Washer

(Qty 4)

M5 x 12mm

Security Screw (Qty 4)

M2.5 x 8mm

Security Screw (Qty 4)

M6 x 12mm Security

Screw (Qty 4)

M2.5 x 10mm

Security Screw (Qty 4)

#14 x 2” Wood Screw

(Qty 2)

M3 x 16mm

Security Screw (Qty 4)

¼-20 x 5/16″ Security

Screw (Qty 1)

M4 x 12mm

Security Screw (Qty 4)

M5 Security Wrench

(Qty 1)

M5 x 10mm

Security Screw (Qty 3)

Barrel Cap

(Qty 4)

Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3

EST150

Features

The Single-Stud Short-Throw Projector Wall Mount (EST150) is a simple and elegant tool for mounting a wide variety
of short-throw projectors. Its design allows you to use the same mount even if you need to replace the projector with a
different model. Unique features include a mount carriage that easily slides along the projector arm for quick screen size
adjustments, integrated cable management, and Lock-It™ security screws and barrel for enhanced security.

Single Stud

Mounts rmly to a

single wood stud.

Projector Adjustment

Position the projector anywhere along
the projector arm.

Radial Glide®

Up to 6°of smooth adjustment
in any direction.

Cable Routing

Discreetly manage signal

and power cables through

the projector arm.

EST-WP (Optional)

The optional EST-WP wall plate

allows for mounting to 12” or 16”
dual studs. The back plate also
allows lateral shift after installation.

Page 4 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions

EST150

Determining the Installation Height

In order to determine the installation height and throw distance, the mount carriage must be mounted

to the projector.

Refer to the projectors User’s Manual to determine the offset of the projector lens to the top of the

screen/whiteboard (B).

Mount Carriage

Projector

Lens

1) Measure distance from center of lens to the top of the mount carriage (C).

2) Add the distance from the ground to the top of the screen (A). Add the projector manufacturers recommended

offset from the projector manual (B). Add the measurement from Step 1 (C), and then add the mounting screw
offset (D) to the total.

(Example: A + B + C + D = ?)

3) Add the measurements to determine the mounting height mark. Place a mark at the top of the total calculated

height measurement starting from the ground up. This height mark will determine your mounting points.

Legend

A - Distance from ground to the top of the
screen/whiteboard (viewable area).

B - Manufacturers recommended offset

measurement. This measurement will
be listed in the Users Manual.

C - Center of the lens to the top of the
projector bracket.

D - If single-stud EST150, add 5.14˝ to

the calculated total.

This total distance will be the location for the

lower mounting point.

Proceed to the “Wood Stud Installation”
section.

Top of Screen

Ground

Mark

D

Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 5