Premier Hazard ShockWave 9005 Installation Instructions Manual
ShockWave
9005 Remote Mount Siren Amplifier
General Installation Instructions
Features Overview:
Personal Announce Radio Rebroadcast channel 1
30 Seconds Play / Record Radio Rebroadcast channel 2
60W/100W/200W outputs Multiple Siren Tones
Horn Ring Transfer of tones HRT polarity detection
Run Interlock
Air-horn Input sidelights
Ignition Input Negative inputs
Data logger output Relay output for beacon control
Relay output for horn by-pass CANBUS communication
Digital Audio Amplifier Digital sound reproduction
Robust Construction Circuit protection
Full backward compatibility with 8000 Series siren amplifier controllers
Approvals:
EMC: ECE REG 10.4, E11 10R-04 8014 NPIA specification 5 (issue 11)
Acoustic: KBA, W 25055
As part of our policy of continuous improvement we reserve the right to change
specifications without notice.
www.premierhazard.co.uk
WARNING THE WORLD®
Emergency Service and Utility Warning Systems
Premier Hazard Ltd., YO16 4SJ, http://www.premierhazard.co.uk,
Tel.: +44(0)113 239 1111, E-Mail: info@premierhazard.co.uk
© 2013 Premier Hazard ltd. A member of the Public Safety Equipment group of companies
D00217-00-A
REL: 39983
2
Contents:
Features Overview 1
Approvals 1
Safety information 2
Electrical Information 3
Fitting Information 3
In the box 3
Product description 4
Controller feature Function table 5
Wiring loom Information 6
Wire size vs distance selection matrix 6
Features 7
Ignition 7
Run 7
Interlock 7
Speaker output 7
Day and night volumes 8
Horn ring transfer (HRT) / Footswitch 8
Data output 8
Relay output (for horn bypass) 9
Relay output (for beacon control) 9
Sidelights input 9
PA 9
PLAY / REC 10
Radio Rebroadcast 1 10
Radio Rebroadcast 2 10
Fault LED 11
Circuit Protection 11
Typical installation diagrams 12
9005 with STC/ MTC 12
9005 with 8006 (RH button Air-horn) 14
9005 with 8006 (RH button beacon) 15
9005 with 8007 16
9005 with CP2 phase II 17
Troubleshooting 19
Safety Information:
Sirens are produced in 12 and 24 Volt versions. Ensure that you have the correct version for your
installation.
A suitable fuse and holder is provided with the siren amplifier wiring loom.
The recommended fuses are: 25A fuse for the 12V version
15A fuse for the 24V version.
The Siren amplifier should be installed by an electrically competent person in accordance with
the fitting instructions.
Any wiring to or from the siren should be sufficient to carry the load, loads are given on page 5,
there is also a wire size selection matrix which may aid this.
Sirens may get hot in use and they should be sited where this will not cause any hazards.
Consideration should be given to allowing air flow over the amplifier.
This equipment generates high levels of sound which may be detrimental to hearing. Care
should be taken during installation and testing so as to avoid endangering yourself or others.
Use of this equipment does not guarantee right of way over other road users and may not
always be heard by them. It should be operated only by trained and competent personnel.
D00217-00-A
REL: 39983
3
Electrical Information:
Operating Voltage range 12V model: 11V – 16V (use 25A fuse)
Operating Voltage range 24V model: 22V – 32V (use 15A fuse)
Speaker requirements: 11 Ohm impedance, 100W
rms
loudspeaker.
Or 2 * 11 Ohm impedance, 100W
rms
loudspeakers
connected in parallel.
Radio rebroadcast 1 & 2 inputs 0.5V
p-p
– 10V
p-p
input range, 10K Ohm impedance
Standby current with power on < 20mA
Standby current without power on < 1mA
(Current consumption due to feeds on the input lines, such as the horn)
Maximum operating current: 20A
Operating temperature range: - 30oC to + 65C
Maximum continuous operation: 5 hours due to limitations with speaker(s)
This could be more or less when in an audio mode such as
PA, PLAY, RADIO depending on input frequencies and
volume levels.
Fitting information:
Leave room for airflow around the siren (approx. 50mm).
Don’t place any wiring directly on the siren casing.
The siren amplifier is not waterproof, so should be fitted in a suitable location.
In The Box:
9005 siren amplifier Quantity x1 PH PN: 9005-12-00 or 9005-24-00
General Installation Instructions Quantity x1 PH PN: D00217-00-A
Wiring loom including fuse Quantity x1 PH PN: ME9005 SERIES
D00217-00-A
REL: 39983
4
Product description:
The 9005 siren amplifier is part of a modular approach to siren and vehicle lighting control. Various
controllers can connect to the siren which allows various operational modes to be enabled whilst
connected to the amplifier via a CANBUS enabled communication lead (see below for details).
The tones and operational modes are selected by the controller see individual controller datasheets for
available tones and features.
STC
STC PIC siren tone control, HRT & PA, data out, RL1 out
MTC
MTC PIC siren tone control, HRT & PA, data out, RL1 out
8006
006 PIC siren tone control, PA, Airhorn, Beacon output,
backlighting, interlock, run, data out, RL1 out
9005 PIC 8007
007 PIC siren tone control, HRT, PA, Airhorn, Play/REC, Radio 1,
Radio 2, interlock, run, data out, RL1 out
CP2
CP2 PIC siren tone control, HRT, PA, Play/REC, Radio 1 & 2,
Interlock, run, data out, RL1 out
D00217-00-A
REL: 39983
5
Controller feature Function Table
CONTROLLER
OPTION
STC
CONTROLLER
MICROPHONE
CONTROLLER
DIN SLOT PHASE 2
CONTROLLER
CONTROLLER &
MICROPHONE
IMAGE
PART No. SERIES
STC
SERIES
CP1-9005-DV
SERIES
CP2-9005-DV
SERIES
CP3-9005-DV
SERIES
P.A. FUNCTION
X X X
X
PLAY/RECORD
FUNCTION
X
X
RADIO
RE-BROADCAST 1
X
X
RADIO
RE-BROADCAST 2
X
SIREN TONE
CONTROL
X X X
X
RELAY OUTPUT
X
X
DATA OUTPUT
X X X
X
RUN INPUT
X X
X
BEACON
INTERLOCK
X X X
X
CANBUS
COMMUNICATION
X X X
X
AUTOMATIC HORN
SWITCH POLARITY
DETECTION
X X X
X
D00217-00-A
REL: 39983
6
Wiring Loom information:
View from rear of connectors
Pin No
Wire Colour:
Function:
Wire size:
+
Red
Battery input positive feed
2mm2 (28/0.3mm) 20A
-
Black
Battery negative return feed
2mm2 (28/0.3mm) 20A
1
Brown
Speaker Common
1.5mm2 (21/0.3mm) 10A
2
NC
60W
1.5mm2 (21/0.3mm) 10A
3
Brown / white
100W / 200W
1.5mm2 (21/0.3mm) 10A
4
Light blue / orange
Radio 1a
0.75mm2 (24/0.2mm) 2A
5
Gray / orange
Radio 2a
0.75mm2 (24/0.2mm) 2A
6
White
Run
0.75mm2 (24/0.2mm) 200mA
7
White/black
Sidelights
0.75mm2 (24/0.2mm) 200mA
8
Green
Input 3
0.75mm2 (24/0.2mm) 200mA
9
Yellow
Input 2
0.75mm2 (24/0.2mm) 200mA
10
Yellow / black
Input 1
0.75mm2 (24/0.2mm) 200mA
11
Light blue
Relay driver output 1
0.75mm2 (24/0.2mm) 200mA
12
Light blue / black
Relay driver output 2
0.75mm2 (24/0.2mm) 200mA
13
Black
Chassis return
0.75mm2 (24/0.2mm) 2A
14
Light blue / white
Radio 1b
0.75mm2 (24/0.2mm) 2A
15
Gray / white
Radio 2b
0.75mm2 (24/0.2mm) 2A
16
Pink
Data logger output
0.75mm2 (24/0.2mm) 200mA
17
Red
Ignition input
0.75mm2 (24/0.2mm) 2A
18
White / Red
Interlock input
0.75mm2 (24/0.2mm) 200mA
19
Orange
Horn Ring Transfer input
0.75mm2 (24/0.2mm) 200mA
20
Violet
Air-horn input
0.75mm2 (24/0.2mm) 200mA
Wire size selection matrix:
Wire CSA
Maximum permissible current over distance
mm2 AWG
5A
10A
15A
20A
25A
30A
0.34
22
1.8m
0.9m X X X X
0.5
20
2.9m
1.5m
0.9m X X
X
0.75
18
4.5m
2.2m
1.5m
1.2m
0.9m
X
1.5
16
7.5m
3.5m
2.4m
1.8m
1.5m
1.2m
2.0
14
12m
6m
4m
2.8m
2.5m
2m 4 11
20m
9.5m
6m
4.7m
3.8m
3.2m
6
10
30m
15m
10m
7.5m
6m
5m
10 8 48m
24m
16m
11.8m
9.4m
8m
16 6 75m
37m
25m
18.8m
15m
12.6m
25
4
120m
60m
40m
30m
24m
20m
4
14
+
10
20
-
15 16 17 18 19
765 8 9
11 12 13
1 2 3
D00217-00-A
REL: 39983
Loading...