Premier Builders Guild Jet Signature, Two-Rock Jet Signature Owner's Manual

OWNERS MANUAL

Dear Customer,

Thank you for your purchase of a

amplifier from Premier Builders

Guild.

As a discerning guitarist, you know the road to great tone begins with
great components.

Our Classic Design, carefully selected parts and hand-built approach
combine to make an extremely versatile instrument.

Please take the time to read this manual. We hope it will answer any
questions that you may have.

We extend a warm welcome to you as a member of a select group of
musicians who have chosen a amplifier.

Important Safety Instructions

1. Read these instructions

2. Keep these instructions

3. Heed all warnings

4. Follow all instructions

5. Do not use this apparatus near water

6. Clean only with dry cloth

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions

8. Do not install near any heat sources such as radiators, heat registers, plugs, and the point
where they exit from the apparatus

9. Protect the power cord from being walked on or pinched particularly at plugs and the point
where they exit from the apparatus

10. Only use attachments/accessories specified by the manufacturer

11. Unplug this apparatus during lightning storms or when unused for long periods of time

12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped

13. CAUTION: To disconnect the unit completely from the MAINS, unplug the unit. Turning the power
switch off does not disconnect the unit completely from the MAINS.

Front Panel Functions

1.

Input Jack

- High impedance input to the amplifier. Plug in your instrument here.

2.

Push/Pull Treble Control

- Adjusts the high frequency response. In the full counter-clockwise

position, high frequencies are bypassed to ground. In the full clockwise position, high frequencies

are allowed to pass to the next gain stage. When the knob is in the “out” position, the high

frequency response is boosted. This is most effective when the input gain is set at 12 o’clock or
lower. The effect is less dramatic as the input gain control is adjusted past the 12 o’clock position.

3.

Push/Pull Mid Control

- Adjusts the mid-range response. In the full counter-clockwise position,
the tone will be somewhat “scooped” of mid-range response, emphasizing the highs and lows. In
the full clockwise position, mid-range frequencies are allowed to pass to the next gain stage.
When the knob is in the “out” position, the mid range frequency response is boosted.

4.

Push/Pull Bass Control

- Adjusts the bass response. In the full counter-clockwise position, low
frequencies are cut. In addition, the response of the treble and mid-range controls is greatly
reduced. In the full clockwise position, low frequencies are allowed to pass to the next gain stage.
When the knob is in the “out” position, the low and low-mid frequencies are boosted. This is a low
frequency contour switch, changing the low and low-mid response.

5.

Input Gain

- Adjusts the overall gain of the amplifier. Start with this control in the 12 o’clock
position. Keep in mind that the amount of gain set here determines the signal level feeding the
lead channel. Low gain settings of this control will require higher lead gain settings for the same
amount of overdrive.

6.

Master Volume

- Adjusts the output level of the clean and lead channels.

7

. Lead Gain

- Adjusts the input level (gain) of the lead channel.

8.

Lead master

- Adjusts the output level of the lead channel.

9.

Reverb

- The front panel reverb control is the return, or mix, control. The reverb effect is
defeated with this control in the full counter clockwise position. Use in conjunction with the reverb
drive control (see REAR PANEL FUNCTIONS, next page).

10.

Stand-by Switch

- Should be in the “down” or “stand-by” position when you apply power to the

unit. After a few seconds, place the switch in the “up” position to use the amplifier. You may leave

the unit “powered up” and place this switch in the “stand-by” position to mute the output.

11. Indicator Lamp- This lamp will illuminate when the power switch is in the “up” position,
indicating the unit is receiving A/C power