Precor CLIMBER 835 User Manual

Assembling and Maintaining
the 835 Climber

Edition Information

ASSEMBLING AND MAINTAINING THE 835 CLIMBER

P/N 300714-241 rev E

Copyright © February 2011 Precor Incorporated. All rights
reserved. Specifications subject to change without notice.

Trademark Note

Precor, AMT, and EFX are registered trademarks and Preva is
a trademark of Precor Incorporated. Other names in this
document may be the trademarks or registered trademarks of
their respective owners.

Intellectual Property Notice

All rights, title, and interests in and to the software of the
Preva Business Suite, the accompanying printed materials,
any copies of such software, and all data collected via the
Preva Business Suite, are exclusively owned by Precor or its
suppliers, as the case may be.

Precor is widely recognized for its innovative, award-winning
designs of exercise equipment. Precor aggressively seeks U.S.
and foreign patents for both the mechanical construction and
the visual aspects of its product design. Any party
contemplating the use of Precor product designs is hereby
forewarned that Precor considers the unauthorized
appropriation of its proprietary rights to be a very serious
matter. Precor will vigorously pursue all unauthorized
appropriation of its proprietary rights.

Precor Incorporated
20031 142nd Ave NE, P.O. Box 7202
Woodinville, WA 98072-4002
1-800-347-4404

http://www.precor.com

Important Safety Instructions

Read the following precautions thoroughly before you begin
assembly, and save them afterward for future reference.

Safety Precautions

Always follow basic safety precautions when using this
equipment to reduce the chance of injury, fire, or damage.
Other sections in this manual provide more details of safety
features. Be sure to read these sections and observe all safety
notices. These precautions include the following:

 Read all instructions in this guide before installing and

using the equipment and follow any labels on the
equipment.

 Make sure all users see a physician for a complete

physical examination before they begin any fitness
program.

 Il est conseillé de subir un examen médical complet avant

d’entreprendre tout programme d’exercise. Si vous avez des
étourdissements ou des faiblesses, arrêtez les exercices
immédiatement.

 Do not allow children, or people unfamiliar with the

operation of this equipment, on or near it. Do not leave
children unsupervised around the equipment.

 Make sure all users wear proper exercise clothing and

shoes for their workouts and avoid loose or dangling
clothing. Users should not wear shoes with heels or
leather soles, and they should check the soles of their
shoes to remove any dirt and embedded stones. They
should also tie long hair back.

 Never leave the equipment unattended when it is plugged

in. Unplug the equipment from its power source when it is
not in use, before cleaning it, and before providing
authorized service.

Note: The optional power adapter is considered a power
source for self-powered equipment.

4 Assembling and Maintaining the 835 Climber

 Use the power adapter provided with the equipment. Plug

the power adapter into an appropriate, grounded power
outlet as marked on the equipment.

 Care should be taken when mounting or dismounting the

equipment.

 Read, understand, and test the emergency stop

procedures before use.

 Keep the power cord or optional power adapter and plug

away from heated surfaces.

 Route power cables so that they are not walked on,

pinched, or damaged by items placed upon or against
them, including the equipment itself.

 Ensure the equipment has adequate ventilation. Do not

place anything on top of or over the equipment. Do not
use on a cushioned surface that could block the
ventilation opening.

 Assemble and operate the equipment on a solid, level

surface.

 Proper Location for Equipment

 For all equipment other than treadmills: Locate at

least 40 inches (1 meter) away from walls or
furniture on either side of the equipment, and 40
inches (1 meter) away from objects behind the
equipment.

 For treadmills: Locate at least 40 inches (1 meter)

away from walls or furniture on either side of the
treadmill, and at least 80 inches (2 meters) away
from objects behind the treadmill.

 Keep equipment away from water and moisture. Avoid

dropping anything on or spilling anything inside the
equipment to prevent electric shock or damage to the
electronics.

 Do not operate electrically powered equipment in damp

or wet locations.

 Never operate this equipment if it has a damaged cord or

plug, if it is not working properly, or if it has been dropped,
damaged, or exposed to water. Call for service
immediately if any of these conditions exist.

 Maintain the equipment to keep it in good working

condition, as described in the Maintenance section of the
assembly and maintenance guide. Inspect the equipment
for incorrect, worn, or loose components, and then
correct, replace or tighten prior to use.

Important Safety Instructions 5

 If you plan to move the equipment, obtain help and use

proper lifting techniques. refer to the "Moving the
Equipment" section of the assembly and maintenance
guide.

 Use the equipment only for its intended purpose as

described in this manual. Do not use accessory
attachments that are not recommended by Precor. Such
attachments may cause injuries.

 Do not operate the equipment where aerosol (spray)

products are being used or where oxygen is being
administered.

 Do not use outdoors.
 Do not attempt to service the equipment yourself, except

to follow the maintenance instructions in this manual.

 Never drop or insert objects into any opening. Keep hands

away from moving parts.

 Do not set anything on the stationary handrails,

handlebars, control console, or covers. Place liquids,
magazines, and books in the appropriate receptacles.

 Do not lean on or pull on the console at any time.

CAUTION : DO NOT remove the cover, or you may risk injury due
to electric shock. Read the assembly and maintenance guide
before operating. There are no user-serviceable parts inside.
Contact Customer Support if the equipment needs servicing. For
use with single phase AC supply only.

Educating Users

Take time to educate users about the Important Safety
Instructions found in both the User Reference Manual and
Product Owner’s Manual. Explain to your club or facility
patrons that they should observe the following precautions:

 Hold onto a stationary handrail or handlebar while

assuming the starting position on the equipment.

 Face the console at all times.
 Hold on to a stationary handrail or handlebar with one

hand whenever you operate the console keys with the
other hand.

6 Assembling and Maintaining the 835 Climber

Hazardous Materials and Proper Disposal

The batteries within self-powered equipment contain
materials that are considered hazardous to the environment.
Federal law requires proper disposal of these batteries.

If you plan to dispose of your equipment, contact Precor
Commercial Products Customer Support for information
regarding battery removal. Refer to Obtaining Service.

Product Recycling and Disposal

This equipment must be recycled or discarded according to
applicable local and national regulations.

Product labels, in accordance with European Directive
2002/96/EC concerning waste electrical and electronic
equipment (WEEE), determine the framework for the return
and recycling of used equipment as applicable throughout the
European Union. The WEEE label indicates that the product is
not to be thrown away, but rather reclaimed upon end of life
per this Directive.

In accordance with the European WEEE Directive, electrical
and electronic equipment (EEE) is to be collected separately
and to be reused, recycled, or recovered at end of life. Users
of EEE with the WEEE label per Annex IV of the WEEE
Directive must not dispose of end of life EEE as unsorted
municipal waste, but use the collection framework available
to customers for the return, recycling, and recovery of WEEE.
Customer participation is important to minimize any potential
effects of EEE on the environment and human health due to
the potential presence of hazardous substances in EEE. For
proper collection and treatment, refer to Obtaining Service.

Regulatory Notices for the RFID Module

When equipped with a control console as described in this
document, this equipment may include a radio-frequency
identification (RFID) module. The RFID module has been
certified to operate at temperatures between -20ºC and 85°C
(-4°F and 185°F).

Important Safety Instructions 7

Radio Frequency Interference (RFI)

The RFID module conforms to the following national
standards defining acceptable limits for radio frequency
interference (RFI).

Federal Communications Commission, Part 15

This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a commercial
installation. The equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the owner’s manual instructions, can cause
harmful interference to radio communications.

Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.

WARNING

Per FCC rules, changes or modifications not
expressly approved by the manufacturer could
void the user’s authority to operate the
equipment.

Industry Canada

This device complies with RSS-210:2007 of the Spectrum
Management & Telecommunications Radio Standards
Specification. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.

This Class A digital apparatus complies with Canadian
ICES-003.

Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.

ATTENTION: Haute Tension
Débranchez avant de réparer

8 Assembling and Maintaining the 835 Climber

European Applications

CE compliance is claimed to the following directives:

 1999/5/EC R&TTE Directive
 2006/95/EC LVD Directive
 2002/95/EC RoHS Directive

Directive compliance has been verified to the following
standards:

 EN 55022
 EN 300 330-1 V1.5.1
 EN 300 330-2 V1.3.1
 EN 301 489-3 V1.4.1
 EN 301 489-1 V1.8.1
 EN 60950-1

Regulatory Notices for Cardiovascular Exercise Equipment

The regulatory information in this section applies to the
exercise equipment and its control console.

Safety Approvals for Cardiovascular Equipment

Precor equipment has been tested and found to comply with
the following applicable safety standards.

Cardiovascular Type Equipment:

 CAN/CSA, IEC, EN 60335-1 (Household and similar

electrical appliances - Safety)

 EN 957 (Stationary training equipment, class S/B

compliant equipment)

Important Safety Instructions 9

Radio Frequency Interference (RFI)

This Precor exercise equipment conforms to the following
national standards defining acceptable limits for radio
frequency interference (RFI).

Federal Communications Commission, Part 15

This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a commercial
installation. The equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the owner’s manual instructions, may cause
harmful interference to radio communications.

WARNING

Per FCC rules, changes or modifications not
expressly approved by Precor could void the
user’s authority to operate the equipment.

Industry Canada

This Class A digital apparatus complies with Canadian
ICES-003.

Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.

ATTENTION: Haute Tension
Débranchez avant de réparer

European Applications

CE compliance is claimed to the following directives:

 2004/108/EC EMC Directive
 2006/95/EC LVD Directive
 2002/95/EC RoHS Directive

Directive compliance has been verified to the following
standards:

 EN 55022
 EN 55024
 EN 60335-1
 EN 60065 (P80 and PVS)

10 Assembling and Maintaining the 835 Climber

Electrical Recommendations: All Equipment Excluding Treadmills

Note: This is a recommendation only. NEC (National Electric
Code) guidelines or local region electric codes must be
followed.

For equipment fitted with a P80 console or Personal Viewing
System (PVS) screen a separate power connection is
required. For a 20 amp branch circuit up to 10 screens can be
connected. If the branch circuit has any other devices plugged
into the circuit the number of screens must be reduced by the
wattage of the other devices.

Note: The typical splitter power cords that have IEC-320 C13
and C14 plugs have a recommended maximum capacity of
five screens.

Figure 1: IEC-320 C13 and C14 plugs

Obtaining Service

Do not attempt to service the equipment except for
maintenance tasks. If any items are missing, contact your
dealer. For more information regarding customer support
numbers or a list of Precor authorized service centers, visit
the Precor web site at http://www.precor.com.

Obtaining Updated Documentation

Current documentation for Experience Series consoles and
Preva Networked Fitness software is available at
http://www.precor.com/productmanuals. You may want to
check in for updated information from time to time as the
universe of Preva features expands.

Table of Contents

Important Safety Instructions ................................................... 3

Safety Precaution s .................................................................................3

Educating Users .................................................................................... 5

Hazardous Materials and Proper Disposal .................................... 6

Product Recycling and Disposal ....................................................... 6

Regulatory Notices for the RFID Module ....................................... 6

Regulatory Notices for Cardiovascular

Exercise Equipment ...................................................................... 8

Electrical Recommendations: All Equipment

Excluding Treadmills .................................................................. 10

Obtaining Service ................................................................................ 10

Obtaining Updated Documentation .............................................. 10

Assembling the Climber ...........................................................13

Unpacking the Equipment ................................................................. 13

Preparing for Installation ................................................................... 13

Assembling the Climber .................................................................... 15

Attaching the Handrails .................................................................... 20

Making Sure the Unit Is Stable ........................................................ 22

Installing the Console .............................................................. 23

Threading the Cable Assembly ....................................................... 23

Connecting Cables (P30) ................................................................. 25

Completing the Console Installation ............................................. 26

Verifying That the Heart Rate Display Is Operational .............. 26

Maintenance ............................................................................ 27

Daily Cleaning ...................................................................................... 27

Daily Inspection ................................................................................... 28

Storing the Chest Strap ..................................................................... 28

Moving the Equipment ...................................................................... 29

Long-Term Storage ............................................................................ 29

12 Assembling and Maintaining the 835 Climber

Self-Powered Features ............................................................. 31

Informational Displays Prior to Shutdown ................................... 32

Symptoms of a Low Battery ............................................................. 32

Using the Optional Power Adapter ................................................ 33

The Optional Power Adapter Kit ..................................................... 33

Replacing the Battery ........................................................................ 34

Commercial Cardiovascular Equipment Limited Warranty .... 35

Chapter 1

Assembling the Climber

Thank you for choosing Precor. For proper installation, please
read this guide thoroughly and follow the assembly
instructions. If you do not assemble the climber according to

Unpacking the Equipment

these guidelines, you could void the Precor Limited Warranty.

Ask for help from two or more people to unpack and
assemble the climber.

Preparing for Installation

DANGER

Follow these installation requirements when assembling the
unit:

 Assemble the unit near the location where you plan to use

it.

 Provide ample space around the unit. Open space around

the unit allows for easier access.

 Set up the unit on a solid, flat surface. A smooth, flat

surface under the unit helps keep it level. A level unit has
fewer malfunctions.

 Open the box and assemble the components in the

sequence presented in this guide.

 Insert all fasteners with your fingers. Use your fingers to

properly align and thread the fasteners. This helps
alleviate cross-threading. Do not fully wrench tighten
fasteners until instructed to do so.

Do not attempt to connect electrical power until all
assembly procedures are complete and the console
is properly installed.

14 Assembling and Maintaining the 835 Climber

Important: When wrench tightening, the head of the fastener
should be flush with the product. If it is not, cross-threading
has occurred. Do not attempt to rework the assembly as more
damage to the equipment will occur. Contact Customer
Support. Refer to Obtaining Service.

 If you plan to move the unit, obtain help and use a hand

truck. Do not grasp any plastic parts while lifting or
moving the unit. The plastic parts are not capable of
supporting the weight of the unit and they may break.

Hardware Kit (not to scale)

Fasteners

Washer (⁵₁₆-inch inside
diameter, 0.688-inch outside
diameter)

Buttonhead screw (¹₂-inch) 6

Hex head screw (1-inch) 4

Sockethead cap screw
(1¹₄-inch)

Phillips-head screw (³₄-inch) 3

End cap 2

Lower handrail boot 2

Quantity

4

2

Assembling the Climber 15

Required Tools

Before beginning the installation, make sure you have the
following tools available:

 Wire tie cutter
 Phillips screwdriver
 One ¹₂-inch combination wrench (open-end or box-end)
 SAE Standard socket set
 Standard set of hex keys

Assembling the Climber

A fish tape (a thin metal strip with a hook or clasp on one end,
available from professional hardware vendors) can be helpful
during this procedure.

To assemble the main climber mechanism:

1. Place the upright support on a flat work surface.

2. Remove the two hex nuts and washers that secure the
handrail clamp, then set them aside.

Figure 2: Removing handrail clamp nuts

3. While your assistant holds the heart rate handlebar near
the display console, feed the heart rate cable through the
opening in the upright support. Pull the end of the cable
out through the top of the support and pass it through the
opening in the console mount as shown in the following
illustration. Place excess cable inside the upright support.

Important: Do not stretch, crimp, or damage the cables.
Cables damaged by improper installation will not be covered
by the Precor Limited Warranty.

16 Assembling and Maintaining the 835 Climber

4. Insert the handlebar flange onto the screws protruding
through the handrail clamp). Rotate the handlebar to align
it with the side screw holes.

CAUTION: Hold the handlebar upright until it is securely
fastened in step 6.

Figure 3: Threading the heart rate cable and moving the
handlebar into place

5. Thread the two hex nuts and washers (removed earlier)
back onto the screws.

Important: Do not tighten the two hex nuts at this time.

6. Attach and fully tighten two buttonhead screws to secure
the handlebars, as shown in the following illustration.

Figure 4: Securing the handlebars in place

Assembling the Climber 17

7. Slide the plastic top cover onto the upright support.

Important: The correct orientation of the plastic top cover is
shown in the following illustration.

8. Retrieve the cable assembly from the console container
and remove any packaging ties. Feed the cable assembly
through the opening in the console mount, then down
through the upright support, and finally out through the
opening in the lower back of the support, as shown in the
following illustration.

Figure 5: Routing cables through the upright support

18 Assembling and Maintaining the 835 Climber

9. Ask your assistant to hold the upright support while you
attach it to the base frame using four hex head screws
and four washers. Using a ¹₂-inch box wrench or
open-end wrench, tighten the four fasteners in alternating
order until all four are fully secured.

Figure 6: Securing the upright support to the climber base

CAUTION: In the following step, be careful to avoid the sharp
edges on the metal bracket. Do not injure yourself when you
connect the cable.

10. Connect the console power cable to its receptacle on the
base frame.

11. Lower the plastic top cover. Tip the cover to insert the
front tab, then align the rear tab. Apply pressure to lock
the rear tab in place.

Assembling the Climber 19

12. Slide the rubber grommet onto the plastic top cover, as
shown in the following illustration. Apply pressure to snap
it into place.

Figure 7: Sliding the grommet into place

20 Assembling and Maintaining the 835 Climber

Attaching the Handrails

Use the following procedure to install the external handrails
on the climber.

To attach the handrails:

1. Slide a lower handrail boot onto each handrail.

Figure 8: Adding the handrail boot

2. Insert the lower handrails onto the base pegs, then slide
the upper portions of the handrails into the handrail clamp
until the foam pads touch the clamp.

Figure 9: Attaching the handrails

Assembling the Climber 21

3. Secure the lower handrails using four buttonhead screws
and a ⁵₃₂-inch hex key. Fully tighten the fasteners.

4. Using a ¹₂-inch socket wrench, tighten the two nuts
beneath the upper handrail clamp until the handrails
cannot be pulled out of the clamp.

5. Position the two lower handrail boots so that the lip on
each boot faces outward. Slide the boots down onto the
rear crossbar.

6. Position the end caps so that they cover the ends of the
rear crossbar and the lips on the lower handrail boots.
Attach the end caps using two socket head cap screws
and a ⁵₃₂-inch hex key. Tighten the fasteners completely.

Important: The lip of each lower handrail boot should fit
beneath the end cap.

Figure 10: Attaching the end caps

7. Position the water bottle holder as shown and attach it to
the right handrail. Secure the holder using three
Phillips-head screws and a Phillips screwdriver.

Figure 11: Attaching the bottle holder

22 Assembling and Maintaining the 835 Climber

8. Clean the foot steps, plastic covers and upright support
with a soft cloth or wipe moistened with an appropriate
cleaning solution. For more information about which
cleaners to use, refer to Daily Cleaning.

9. Level the climber as described in the section Making Sure
the Unit Is Stable.

Important: Do not allow anyone to use the climber until it has
been leveled and made stable.

Making Sure the Unit Is Stable

Make sure the unit is level before allowing anyone to use it.

CAUTION: To eliminate movement, make sure the adjustable feet
are in contact with the floor.

To level the unit:

1. Gently rock the unit. If there is any movement, ask your
assistant to tip the unit to one side while you locate the
adjustable feet.

2. Correct the height of each adjustable foot as follows.

If you want to … Then turn the adjustable feet …

Raise the unit Counterclockwise

Lower the unit Clockwise

Important: Place the unit on a flat surface. Rotating the
adjustable feet cannot compensate for extremely uneven surfaces.

When you are finished adjusting the unit, place the unit on the
floor and recheck that it is level.

Installing the Console

To make installation easier, all Precor Experience Series
consoles use the same mounting hardware and connector
locations whenever possible. The installation sequence for
any of them is as follows:

 Threading the cable assembly
 Connecting cables
 Completing the installation (tightening the mounting

screws and attaching the back cover)

The following sections describe how to perform these tasks.

Chapter 2

Threading the Cable Assembly

Earlier in the installation, you threaded the necessary cables
through the frame of the base unit and out the passthrough
opening in the console mount. As you line up the back plate
on the console with the console mount, you must make sure
that the cable assembly passes correctly through the
openings in both components.

Important: Before you begin the following procedure, remove the
rear cover from the control console. Set the cover and its mounting
hardware aside for later use.

To thread the cable assembly:

1. Make sure that as much of each cable as possible passes
through the opening in the middle of the console mount
on the base unit.

2. Position the console over the console mount.

24 Assembling and Maintaining the 835 Climber

3. Rest the console on the console mount so that the notch
on the bottom of the console’s back plate rests on the
rectangular hook at the bottom of the console mount, as
shown in the following figure.

Figure 12: Console positioning on base unit

4. Tilt the console forward until it stops. Use one hand to
steady the console in this position, or ask your assistant
to do so.

5. Pull all cables upward and forward until you can drape
them over the top of the console’s back plate.

Installing the Console 25

Connecting Cables (P30)

After the console has been seated, separate the individual
cables out of the end of the cable assembly and attach them
to the appropriate circuit connectors inside the console. Refer
to the following diagram and table to identify the cables and
connectors.

Figure 13: Cable connections, P30 console

Table 1. P30 internal cable connections

Cable Connector Type Circuit Connector

Location

Safety key
(treadmills only)

Auto Stop sensor
(treadmills only)

Data from base unit Eight-contact modular,

Heart rate sensors Four-contact strip, keyed

Six-contact strip, keyed

Four-contact strip, keyed

on flat gray cable

26 Assembling and Maintaining the 835 Climber

Completing the Console Installation

Before you complete the final installation steps, double-check
the connections you have made. Make sure that all cables are
fully and securely connected, and that any unneeded cables
are tied back properly.

To complete the installation:

1. Feed extra cable back into the neck tube.

2. Tilt the control console backward (toward yourself) until
the tab on the top edge of its back plate slides along the
top edge of the console mount and the screw holes align
properly.

3. Insert the four ⁵₈-inch flat head screws through the holes
in the console mount and thread them into the holes in
the back plate on the console. Partially tighten the screws
using a ⁵₈-inch hex wrench.

4. Line up the two small tabs at the bottom of the console’s
back cover with the slots at the bottom of the console
case. Insert the tabs into the slots.

5. Insert the two #8–32 x ¹₂-inch Phillips-head screws that
you removed earlier into the holes at the top edge of the
console’s back cover. Tighten the screws fully.

Important: Use caution not to pinch the cables between the
back cover and PVS mounting screw heads.

6. Fully tighten the four mounting screws (partially
tightened in step 3) using a ⁵₃₂-inch hex wrench.

Verifying That the Heart Rate Display Is Operational

To verify that the heart rate display is operational:

1. Begin exercising on the equipment.

2. Grasp both touch-sensitive handlebars.
Note: The heart rate is read within ten seconds. During

that time, the heart on the display flashes.

3. Look at the HEART RATE display. After a few seconds, a
number appears indicating your heart rate.

4. If a number does not appear in the HEART RATE display,
check the cable connection to make sure it is properly
connected.

Maintenance

To keep the equipment functioning properly, perform the
minor maintenance tasks in this section at the intervals
shown on the maintenance checklist. Failure to maintain the
equipment as described in this section could void the Precor
Limited Warranty.

Chapter 3

DANGER

Daily Cleaning

Precor recommends that you clean the equipment before and
after each exercise session. To remove dust and dirt from the
equipment, wipe all exposed surfaces with a soft cloth that
you have moistened with one of the following cleaners:

 A solution of 30 parts of water to 1 part of Simple Green®

(for more information, visit www.simplegreen.com)

 ENVIR-O-SAFE oxygen enhanced cleaner or multi-task

cleaner concentrate, diluted according to the
manufacturer’s instructions (for more information, visit

www.daleyinternational.com)

To reduce the risk of electrical shock, always
disconnect the equipment from its power source
before cleaning it or performing any maintenance
tasks. If the equipment is self-powered but also
uses the optional power adapter, disconnect the
adapter.

28 Assembling and Maintaining the 835 Climber

Alternatively, you can clean the equipment with Athletix
fitness equipment cleaning wipes (for more information, visit

www.athletixproducts.com)

CAUTION
particularly dilution instructions, before using any cleaner on
Precor fitness equipment. Do not use concentrated cleaners at full
strength, or acidic cleaners of any kind; such cleaners weaken the
protective finish on the equipment and void the Precor Limited
Warranty. Never pour water or spray liquids onto any part of the
equipment. Allow the equipment to dry completely before using.

: Read and follow the manufacturer’s instructions,

Vacuum the floor underneath the equipment frequently to
prevent the accumulation of dust and dirt that can interfere
with its operation. Use a soft nylon scrub brush to clean the
grooves on equipment with foot pedals.

Daily Inspection

At least once every day, examine the equipment for the
following problems:

 Slipping belts
 Loose fasteners
 Unusual noises
 Worn or frayed power cords
 Any other indication that the equipment may be in need

of service

Important: If you determine that the equipment needs service,
disconnect all power connections (television, Ethernet, and power)
and move the equipment away from the exercise area. Place an
OUT OF SERVICE sign on the equipment and make it clear to all
patrons and other users that they must not use it.

To order parts or to contact a Precor authorized service
provider in your area, refer to Obtaining Service.

Storing the Chest Strap

If you purchased the optional heart rate chest strap, store it in
a place where it remains free of dust and dirt (for example, in
a closet or drawer). Be sure to protect the chest strap from
extremes in temperature. Do not store it in a place that may
be exposed to temperatures below 32° F (0° C).

To clean the chest strap, use a sponge or soft cloth dampened
in mild soap and water. Dry the surface thoroughly with a
clean towel.

Maintenance 29

Moving the Equipment

The equipment is very heavy. If you plan to move it to a new
location, obtain the help of an adult assistant and use proper
lifting techniques. If the equipment includes roller wheels on
one end, use the wheels to reduce the load on yourself and
your assistant.

To move the climber:

1. Disconnect, unplug, and remove all external connections
(television, Ethernet, and power).

2. Grasp the climber by its upright support and tip it forward
onto its roller wheels.

3. Push the climber into its new location.

4. Lower the rear foot supports to the floor.

5. Push the climber back and forth to verify that it sits flat on
the floor. If it rocks at all, or if it does not appear to be
level, correct it by adjusting its rear feet.

Long-Term Storage

If you do not expect anyone to use the equipment for a long
time, perform the following tasks to prepare it for storage:

 If it has a power cord, disconnect the cord.
 If it has an optional power adapter, connect the adapter to

prevent damage to the internal battery.

 Position it so that it will not become damaged and will not

interfere with people or other equipment.

30 Assembling and Maintaining the 835 Climber

Chapter 4

Self-Powered Features

Important: This chapter of the manual describes Precor fitness
equipment that can operate without being connected to AC
power. This includes units equipped with P40 or P20 consoles.
However, P80 consoles must be connected to AC power through
their power supplies to operate. For this reason, this chapter does
not apply to units equipped with P80 consoles.

On self-powered equipment, the system initializes and
displays the Welcome screen when a user starts exercising. A
minimum rate of motion must be maintained for the banner to
appear, as shown in the following table. When a person meets
the requirements, the power that is generated allows the
equipment to function properly.

Table 2. Minimum requirements for operation

Equipment Rate of Motion

AMT 56 strides per minute (SPM)

EFX 40 strides per minute (SPM)

Climber 30 steps per minute

Bike 20 revolutions per minute (RPM)

Informational displays appear when the battery is low or
when the rate of motion drops below the minimum
requirements. The display explains what to do to retain
power. If the messages are ignored, the equipment begins
shutdown procedures to maintain the charge of the battery.
Refer to Informational Displays Prior to Shutdown.

An optional power adapter can be purchased and provides
sustained power to the equipment. If you plan to change the
club settings, the power adapter is highly recommended. To
purchase the optional power adapter, check with your dealer.
Refer to Obtaining Service.

32 Assembling and Maintaining the 835 Climber

Informational Displays Prior to Shutdown

The equipment saves its battery charge by moving into a
shutdown mode. If the user does not maintain the minimum
rate of motion, a 30-second shutdown process begins.

In this mode, the console displays a countdown indicator and
ignores all keypresses. If no movement is detected or the rate
of motion remains below the minimum, the indicator changes
as the countdown continues.

Note: The user can resume exercising before the countdown
period elapses and the program will continue from the point
at which it was paused.

Important: If the equipment is connected to a CSAFE master
device, it follows a slightly different shutdown process. Ten
seconds before the equipment shuts down, it ends the exercise
session and displays a reset message while it disconnects from the
CSAFE master device. It ignores all keypresses during these last
ten seconds.

Symptoms of a Low Battery

If no one has used the equipment for an extended period of
time, the battery may need recharging.

Symptoms of a low battery include the following:

 A flickering or erratic display
 Loss of user and program information after the user stops

exercising, without any display of a workout summary or a
notification of pending shutdown

Important: To maintain a constant power source, use the optional
power adapter.

Self-Powered Features 33

Using the Optional Power Adapter

After connecting the power adapter to the equipment, plug
the opposite end into the appropriate power source (120 V or
240 V).

CAUTION: When the optional power adapter is in use, make sure
that the power supply cord does not create a safety hazard. Keep
it out of the way of traffic and moving parts. If the power supply
cord or power conversion module is damaged, it must be replaced.

The control console functions differently when the power
adapter is connected. Because the power adapter provides a
constant source of power, a user can pause for brief periods
without initiating shutdown procedures. When the pause time
limit expires and the user has not resumed exercising, the
console returns to the Welcome screen. The default pause
time is 30 seconds for all fitness equipment. Refer to the
manual for your control console for instructions on setting or
changing the pause time limit. To learn how to install the
power adapter, refer to The Optional Power Adapter Kit.

The Optional Power Adapter Kit

If you purchase the optional power adapter, you must also
purchase the internal cable kit. The kit supplies the cable,
bracket, and fasteners that connect the power adapter to the
lower electronics board.

CAUTION: The internal cable kit must be installed by authorized
service personnel. Do not attempt installation on your own as you
could void the Precor Limited Warranty. For more information,
refer to Obtaining Service.

Important: If this equipment includes a P80 console, the optional
power adapter and the internal cable kit must still be installed to
provide continuous power to the base unit and support its internal
battery.

Once the internal cable kit is installed, you can plug the
optional power adapter into the equipment. Plug the opposite
end into the appropriate power source for your equipment
(120 V or 240 V). Review the safety instructions found at the
beginning of this manual before using the power adapter.

34 Assembling and Maintaining the 835 Climber

Replacing the Battery

The equipment’s battery is built to last for a long time.
However, if you feel that the battery may need replacing,
check with an authorized service technician. Refer to
Obtaining Service.

CAUTION: The battery stored inside the equipment contains
hazardous materials and must be disposed of according to
Hazardous Waste Regulations. Refer to Hazardous Materials and
Proper Disposal.

Chapter 5

Commercial Cardiovascular Equipment Limited Warranty

PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE
USING YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU
ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND
CONDITIONS.

Limited Warranty.

Precor Incorporated warrants all new Precor products to be free from defects in materials
and manufacture for the warranty periods set forth below. The warranty periods
commence on the invoice date of the original purchase. This warranty applies only against
defects discovered within the warranty period and extends only to the original purchaser
of the product. Parts repaired or replaced under the terms of this warranty will be
warranted for the remainder of the original warranty period only. To claim under this
warranty, the buyer must notify Precor or your authorized Precor dealer within 30 days
after the date of discovery of any nonconformity and make the affected product available
for inspection by Precor or its service representative. Precor’s obligations under this
warranty are limited as set forth below.

Warranty Periods and Coverage.

All Commercial Cardiovascular Products (excluding StretchTrainer, Strength
Products, and coverage specific to certain models and options as defined
below):

 Frame: 7 years
 Treadmill drive motor: 5 years
 Items subject to wear: 1 year
 All other parts (including mechanical parts and electronic parts): 2 years
 Labor: 1 year

880 Line Commercial Cardiovascular Products (superseding the coverage
above where applicable):

 Labor on the P80 console: 2 years
 High wear items on the P80 console, including headphone jack, USB connector, and

iPod® connector: 90 days

36 Assembling and Maintaining the 835 Climber

Options / Accessories

Many options or accessories have components that are connected internally or mounted
inside the electronic console. The following guidelines determine the warranty for these
components. If the internal components are installed by the factory or by an authorized
dealer as part of the original sale and delivery, they have a warranty that is identical to the
warranty of the equipment in which they are connected or mounted. If the internal
components are not installed by the factory or by an authorized dealer as part of the
original sale and delivery, they have a 90 days parts and labor limited warranty. All
components that are not internally connected have a 90 days parts only limited warranty.
Satisfactory proof of purchase is required in all cases.

Conditions and Restrictions.

This warranty is valid only in accordance with the conditions set forth below:

1. The warranty applies to the Precor product only while

a. it remains in the possession of the original purchaser and proof of purchase is

demonstrated.

b. it has not been subjected to accident, misuse, abuse, improper service, or

non-Precor modification.

c. claims are made within the warranty period.

2. This warranty does not cover damage or equipment failure caused by electrical wiring

not in compliance with electrical codes or Precor owner’s manual specifications, or
failure to provide reasonable and necessary maintenance as outlined in the owner’s
manual.

3. Precor is not responsible for Internet connectivity to its products. This restriction

applies to services, such as those provided by an Internet service provider (ISP), and
also to hardware related to Internet connectivity, such as Ethernet cabling, routers,
servers and switches.

4. Precor is not responsible for the quality of television, video, audio, or other media

supplied to its products. This restriction applies to services, such as those provided
by a cable or satellite television provider; to signal strength and clarity; and also to
hardware related to the reception and delivery of television, video, audio, and other
media. Such hardware can include (but is not limited to) audio, video, and
radio-frequency (RF) cabling, connectors, receivers, modulators, combiners,
distribution amplifiers, splitters, and so on.

5. Precor cannot guarantee that the heart rate measurement system on its products will

work for all users. Heart rate measurement accuracy varies based on a number of
factors, including the user’s physiology and age, the method in which the heart rate
measurement system is used, external interference, and other factors that may
influence heart rate acquisition.

6. Except in Canada, Precor does not pay labor outside the United States.

7. Warranties outside the United States and Canada may vary. Please contact your local

Dealer for details.

Commercial Cardiovascular Equipment Limited Warranty 37

This Limited Warranty shall not apply to:

1. Software version upgrades.

2. Software defects that do not materially and negatively affect the normal performance

of the product under normal conditions of use.

3. Consumable goods or cosmetic items of the product, the exterior of which has been

damaged or defaced as a result of abuse, misuse, accident, improper service or
installation, mishandling, or modification in design or construction not authorized by
Precor.

4. Repairs performed on Precor equipment missing a serial number or with a serial tag

that has been altered or defaced.

5. Service calls to correct installation of the equipment or instruct owners on how to use

the equipment.

6. Pickup and delivery involved with repairs.

7. Any labor costs incurred beyond the applicable labor warranty period.

Disclaimer and Release.

The warranties provided herein are the exclusive warranties given by Precor and
supersede any prior, contrary or additional representations, whether oral or written. ANY
IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE THAT APPLY TO ANY PARTS DESCRIBED
ABOVE ARE LIMITED IN DURATION TO THE PERIODS OF EXPRESS WARRANTIES
GIVEN ABOVE FOR THOSE SAME PARTS. PRECOR HEREBY DISCLAIMS AND
EXCLUDES THOSE WARRANTIES THEREAFTER. Some States do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to you. PRECOR
ALSO HEREBY DISCLAIMS AND EXCLUDES ALL OTHER OBLIGATIONS OR LIABILITIES,
EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, WITH RESPECT TO ANY
NONCONFORMANCE OR DEFECT IN ANY PRODUCT, INCLUDING BUT NOT LIMITED
TO: (A) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY IN TORT, WHETHER
OR NOT ARISING FROM THE NEGLIGENCE OF PRECOR OR ITS SUPPLIERS (WHETHER
ACTIVE, PASSIVE OR IMPUTED); AND (B) ANY OBLIGATION, LIABILITY, RIGHT,
CLAIM OR REMEDY FOR LOSS OF OR DAMAGE TO ANY EQUIPMENT. This disclaimer
and release shall apply even if the express warranty set forth above fails of its essential
purpose.

Exclusive Remedies.

For any product described above that fails to conform to its warranty, Precor will provide,
at their option, one of the following: (1) repair; (2) replacement; or (3) refund of the
purchase price. Precor Limited Warranty service may be obtained by contacting the
authorized dealer from whom you purchased the item. Precor compensates Servicers for
warranty trips within their normal service area to repair commercial equipment at the
customer’s location. You may be charged a trip charge outside the service area. THESE
SHALL BE THE SOLE AND EXCLUSIVE REMEDIES OF THE BUYER FOR ANY BREACH OF
WARRANTY.

38 Assembling and Maintaining the 835 Climber

Purchased From:

Phone Number:

Product/model:

Serial number:

EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL
DAMAGES.

PRECOR AND/OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY,
WHETHER ARISING IN CONTRACT (INCLUDING WARRANTY), TORT (INCLUDING
ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE AND STRICT LIABILITY), OR
OTHERWISE, FOR DAMAGE TO THE EQUIPMENT, PROPERTY DAMAGE, LOSS OF USE,
REVENUE OR PROFIT, COST OF CAPITAL, COST OF SUBSTITUTE EQUIPMENT,
ADDITIONAL COSTS INCURRED BY BUYER (BY WAY OF CORRECTION OR
OTHERWISE) OR ANY OTHER INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES, WHETHER RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE
OR INABILITY TO USE THE PRODUCT. This exclusion applies even if the above warranty
fails of its essential purposes and regardless of whether such damages are sought for
breach of warranty, breach of contract, negligence, or strict liability in tort or under any
other legal theory. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which
vary from state to state.

Complete this portion and keep for your records.

Example: Dealer or store name.

Effective 1 November 2010
P/N 36286-114

Example: Dealer or store telephone number.

Example: AMT 885 or EFX 883.

The serial number is found on the shipping container.

Commercial Cardiovascular Equipment Limited Warranty 39

40 Assembling and Maintaining the 835 Climber

Precor Incorporated
20031 142nd Avenue NE
P.O. Box 7202
Woodinville, WA USA 98072-4002

CLM PAG/OM 300714-241 rev E

Warranty #36286-114

14 February 2011