Page 1
C764i Integrated LCD Screen Option
Cardio Theater Integrated Bracket Assembly Instructions
Page 2
Cardio Theater Integrated Bracket Assembly Instructions
Table of Contents
Before You Begin ............................................................................................. 3
1
2
Obtaining Service........................................................................................................................ 3
Unpacking the Equipment ........................................................................................................... 3
Important Safety Instructions ...................................................................................................... 3
Preparations..................................................................................................... 4
Required Tools ............................................................................................................................. 4
Installation Requirements ............................................................................................................ 4
Assembly Tips ............................................................................................................................ 4
Install the Bracket Assembly .......................................................................... 5
3
Feed the Cable through the Base .................................................................. 9
4
Table of Contents
Attach the LCD Screen ................................................................................... 11
5
Reinstall the Bracket Cover ............................................................................ 14
6
Connect the Controller and the Cables ......................................................... 15
7
page 2
Page 3
Cardio Theater Integrated Bracket Assembly Instructions
1
Thank you for adding the Precor Cardio Theater
Integrated LCD Screen Option to your C764i Climber.
This option will add a new dimension to your workout.
For proper installation, please read this guide
thoroughly and follow the assembly instructions.
Obtaining Service
For information about product operation or service,
see the Precor web site at www.precor.com. Should
you need more information regarding customer
support numbers or a list of Precor authorized
service centers, visit the Precor website at
www.precor.com/contact.
Before You Begin
Unpacking the Equipment
The Cardio Theater Integrated Bracket for the LCD
Screen is shipped in one box with the following
items:
• Bracket assembly
• Power extension cable
• Four Phillips-head screws
• Rubber adapter mounts
If any items are missing, contact the dealer
from whom you purchased the unit or call a
Precor Commercial Products Customer Support
Representative.
Important: To complete the assembly of the
Cardio Theater Integrated Bracket, you need the
Cardio Theater LCD Screen Option, which is shipped
in a separate box. Included with the screen are two
cables (coaxial/power cable and controller cable),
which you will need during the assembly process.
Important Safety Instructions
When using exercise equipment, basic
precautions should always be taken,
including the following:
• Read all instructions before using
the unit. These instructions are
written to ensure your safety and to
protect the equipment.
• Use the equipment only for its
intended purpose. Do not use
accessory attachments that are not
recommended by the manufacturer,
as such attachments might cause
injuries.
• Always check the unit before each
use. Make sure that all fasteners and
cables are secure and in good
working condition.
Important: The important safety
instructions written here reflect a portion
of what is found in the Precor climber
owner’s manuals. Please review and
follow the safety instructions found there.
Before You Begin
IMPORTANT SAFETY INSTRUCTIONS
page 3
Page 4
Cardio Theater Integrated Bracket Assembly Instructions
2
Important: To attach the Cardio Theater Integrated
Bracket, ask another adult for help. Do not attempt
the assembly by yourself.
Remember to read and follow the instructions in this
guide. If you do not assemble the Cardio Theater
Integrated Bracket according to these guidelines,
you could void the Precor Limited Warranty.
Required Tools
Obtain these tools before assembly:
• Standard hex key set
• Standard socket set
• ½-inch box wrench or crescent wrench
• Flat head screwdriver
• Phillips-head screwdriver
• Needle-nose pliers
• Standard torque wrench
Preparations
Installation Requirements
Review these installation requirements before
assembly:
• The Cardio Theater Integrated Bracket is built to
VESA MIS-D, 100/75 standard interface specifications.
• Provide ample space around the climber. Open
space around the unit allows for easier access
and installation.
• Open the box and assemble components in the
sequence presented in this guide.
• Leave room for adjustments. Tighten fasteners
(bolts, nuts, and screws) so the unit is stable, but
leave room for adjustments. Do not fully tighten
fasteners until instructed in the assembly steps
to do so.
Assembly Tips
• Read all the notes on each page before completing that step.
• While you may be able to assemble the Cardio
Theater Bracket using the illustrations only,
important safety notes and other tips are
included in the text.
The assembly of the Cardio Theater Bracket takes
about ½ hour to complete.
Preparations
page 4
Page 5
Cardio Theater Integrated Bracket Assembly Instructions
Install the Bracket
3
The illustration shows how the Cardio Theater
Bracket will look after you install it on the climber.
CAUTION: Turn OFF the climber and remove the
power plug from its power source before
proceeding with the assembly.
Assembly
Install the Bracket Assembly
page 5
Page 6
Cardio Theater Integrated Bracket Assembly Instructions
1. Remove the bracket cover.
Loosen the bolts on the pivot tube using a
⁷⁄₃₂-inch hex key. Pull the bracket cover away
from the assembly. Set it aside.
1
2. Feed the coaxial/power cable with its three
connectors through the bracket assembly. Set
the bracket assembly aside.
Important: Make sure you feed the cable so the
end with the three connectors appears out of the
top of the bracket assembly.
2
Coaxial/power
cable with its
connectors
Bracket cover
Bracket
assembly
Bracket
cover
Bracket
assembly
Top of
bracket
assembly
Install the Bracket Assembly
Power
connector
DVD connector
(optional accessory)
Coaxial
connector
page 6
Page 7
Cardio Theater Integrated Bracket Assembly Instructions
3. Pull up the rubber boot along the upright support
until you have about a two foot gap between the
boot and side covers.
3
4. Remove the three fasteners that secure the
display console to the upright support. Rest the
display console between the handlebars.
5. Remove the plastic plug in the upright support.
Upright support
Side covers
4
Display console
Rubber boot
5
Install the Bracket Assembly
Remove three
Remove plastic plug.
fasteners.
page 7
Page 8
Cardio Theater Integrated Bracket Assembly Instructions
6. Feed the coaxial/power cable and its connectors
through the upright support.
Ask your assistant to hold the bracket assembly
close while you insert the cable and its
connectors into the upper hole on the upright
support. Slide the cable down until you can
access the connectors through the lower hole.
Note: You may need to move the ribbon cable
inside the upright support to gain clear access.
7. Pull the cable and its connectors out of the
lower hole. If needed, use a needle-nose pliers
to grasp the cable.
Note: While you pull about 3 feet (1 meter) of
cable out of the lower hole ask your assistant to
align the bracket assembly with the mounting
fasteners on the upright support. Make sure the
bracket assembly slides into place along the
outside of the upright support.
8. Attach the bracket assembly and replace the
fasteners.
Ask your assistant to continue holding the
bracket assembly, while you replace the three
fasteners removed in step 4. Securely tighten
all three screws using a ⁵⁄₃₂-inch hex key.
6
7
Upright support
8
Display console
Bracket assembly
Install the Bracket Assembly
Rubber boot
Coaxial/power cable
(with coaxial and power connectors)
page 8
Page 9
Cardio Theater Integrated Bracket Assembly Instructions
Feed the Cable
4
1. Use a Phillips-head screwdriver to remove the
16 screws that hold the side covers on the unit.
Set the screws aside.
2. Slide both side covers up and away from the
base of the unit.
3. Feed the coaxial/power cable and its connectors
into the internal upright frame tube that does not
contain the ribbon cable.
4. Pull the cable and both connectors out from the
base of the tube and attach the power extension
cable to the power connector.
through the Base
1
3 4
2
Feed the Cable through the Base
Power connector Power
extension
cable
page 9
Page 10
Cardio Theater Integrated Bracket Assembly Instructions
5. Snap the coaxial/power cable into the existing
cable clips as you feed it along the base and
out the front of the unit.
6. Reassemble the side covers. As you face the
display, the right side cover must be placed into
position first. The left side cover fits into it.
Note: Check the connectors on the coaxial/
power cable to make sure they are easily
accessible.
7. Replace the 16 screws removed in step 1 and
reposition the rubber boot.
5
Clip
Coaxial/power cable
(with power extension cable)
Coaxial
connector
Front of
the unit
6
Right side cover
Replace the side cover
screws and lower the
7
rubber boot.
Power
extension
connector
Feed the Cable through the Base
page 10
Page 11
Cardio Theater Integrated Bracket Assembly Instructions
2
Metal mounting
bracket
Attach the LCD
5
Important: The screen spacer is used only for the
Cardio Theater PVS4/5/15 LCD Screen.
1. To protect the LCD Screen for the next few
steps, place it screen side down on a clean
work surface.
Important: Use proper materials to protect the
LCD Screen while you remove the plastic cover
and metal mounting bracket from the backside
of the LCD Screen.
2. Remove the plastic cover.
Use a Phillips-head screwdriver to remove
the two screws holding the plastic cover to
the LCD Screen. Discard the plastic cover and
the screws.
3. Remove the metal mounting bracket.
Remove the four screws securing the metal
mounting bracket. Discard the mounting bracket
and the four screws.
Screen
3
Plastic
cover
LCD
screen
4. Retrieve four new Phillips-head screws
from the bracket assembly package.
Note: Use the longer screws if attaching the
screen spacer with the PVS4/5/15 LCD Screen.
Attach the LCD Screen
page 11
Page 12
Cardio Theater Integrated Bracket Assembly Instructions
5. Attach the LCD Screen to the bracket assembly.
Ask your assistant for help. Have your
assistant hold the LCD Screen against the
bracket assembly while you align the mounting
holes. Insert all four screws and finger tighten.
Important: The screen spacer is used only for
the Cardio Theater PVS4/5/15 LCD Screen. You
will need to insert the screen spacer between
the screen and bracket to ensure a proper fit.
Screen spacer
(PVS4/5/15 LCD Screen only)
5
Bracket assembly
6. Fully tighten the bottom two screws.
Use a Phillips-head screwdriver to fully tighten
the bottom two screws. Leave the top two
screws finger tight.
LCD
screen
Note: The screen spacer rests between the
bracket assembly and the PVS4/5/15 LCD
Screen.
6
page 12
Page 13
Cardio Theater Integrated Bracket Assembly Instructions
7. Connect the coaxial/power cable connectors to
the LCD Screen.
Attach the connectors – coaxial, power, and
DVD – to the back of the LCD Screen.
Note: If you do not have the DVD option, you
can feed the DVD cable back into the pivot tube
compartment so it is not hanging out.
8. Connect the controller cable.
Feed the controller cable through the front side
of the pivot tube and attach it to the back of the
LCD Screen. You will hear a definite click as the
connector snaps into place inside its receptacle.
Note: For more information about cable connections, refer to the Cardio Theater LCD Screen
manual that was packaged with the product.
Important: If you purchased the DVD Integrated
Bracket Option, you will want to install that
option before you continue to the next section.
Refer to the
Guide
DVD Integrated Bracket Option
for assembly instructions.
7
Coaxial
connector
Power
connector
DVD
connector
Note: If you do not have the DVD option,
you can feed the DVD cable back into the
pivot tube compartment so it is not
hanging out.
8
Attach the LCD Screen
Controller
cable
page 13
Page 14
Cardio Theater Integrated Bracket Assembly Instructions
Reinstall the
6
1. Prepare the fasteners for reinstalling the bracket
cover.
Push the washers and bearings toward the bolt
heads so there is room for the bracket cover to
slide in flush against the pivot tube.
Important: Keep the bracket cover flanges flush
with the pivot tube. The washers and bearings
need to remain on the outside of the bracket
flanges.
2. Hold the bracket cover above the pivot tube.
Apply pressure to the top of the bracket cover
while you slide it into position.
3. Tighten the two top screws on the back of the
LCD Screen.
Use a Phillips-head screwdriver to fully
tighten the top two screws on the back of
the LCD Screen. Access holes have been
drilled through the bracket cover.
Bracket Cover
1
3
Bracket
cover
Pivot tube
Bracket cover
2
4
Top of bracket cover
4. Secure the bracket cover.
Using a torque wrench and a ⁷⁄₃₂-inch hex key,
retighten the two pivot tube fasteners to 120 in-lbs.
Reinstall the Bracket Cover
Pivot tube
page 14
Page 15
Cardio Theater Integrated Bracket Assembly Instructions
Connect the
7
Note: Retrieve the rubber adapter mounts from the
bracket assembly package. Retrieve the controller
from the LCD Screen package.
1. Connect the controller cable to the controller.
A definite click is heard when the connector
snaps into place inside its receptacle.
2. Place the rubber adapter mounts around the
center of the bracket bar.
3. Secure the controller.
Use two tie wraps to secure the controller to the
rubber adapter mounts and bracket bar.
4. At the base of the climber, plug the power and
coaxial connectors on the coaxial/power cable
into the strip designed for Cardio Theater use.
Note: For more information, refer to the Cardio
Theater LCD Screen manual.
and the Cables
Controller
1
Controller
Controller cable
LCD screen
Controller
3
Bracket bar
Rubber adapter
mounts
2
Tie wraps
Controller cable
Connect the Controller and the Cables
page 15
Page 16
Precor Incorporated
20031 142nd Avenue NE
P.O. Box 7202
Woodinville, WA USA 98072-4002
Precor and Cardio Theater are registered trademarks of Precor Incorporated.
Specifications subject to change without notice.
Copyright 2005 Precor Incorporated.
Precor web site: www.precor.com
NOTICE:
Precor is widely recognized for its innovative, award winning designs of exercise equipment. Precor aggressively seeks U.S. and foreign patents for
both the mechanical construction and the visual aspects of its product design. Any party contemplating the use of Precor’s product designs is hereby
forewarned that Precor considers the unauthorized appropriation of its proprietary rights to be a very serious matter. Precor will vigorously pursue all
unauthorized appropriation of its proprietary rights.
Cardio Theater Integrated Bracket Assembly Lit Kit # CX48256-102
C764i-series
15 June 2005
Loading...