Precisionaire PB1003 User Manual
PrecisionCell HT
High Temperature Rigid Filters
Bulletin PB1003-1106
General
PrecisionCell HT filters are designed for high temperature applications up to 900
same rugged construction as the Gas Turbine
PrecisionCell. The HT version is manufactured of
specially selected components to meet high temperature requirements.
They are ideal for paint drying ovens or any application requiring high efficiency filtration at high temperatures. PrecisionCell HT filters are offered in two
high temperature operating ranges; 750
F and efficiency ranges of 65%, 85% and 95% per
ASHRAE Standard 52.1. Offered as a MERV 11-14
according to ASHRAE 52.2.
o
F. They feature the
ºF and 900º
Construction
The enclosing frame is manufactured of aluminized
steel, which is designed to eliminate spalling of corrosion inhibitors @ elevated temperatures.
The media pack is stabilized by a media pack
retaining bar and captured by faceguards upstream
and downstream. Grid strap bracing on the air
entering and leaving sides maintain the rigidity and
integrity of the PrecisionCell HT.
The media is designed for operation in high temperature applications and manufactured from one
continuous sheet of wet-laid micro-fine fiberglass,
which provides the required tensile strength and
operating pressure drop for these stringent applications.
Physical Data
Frame: 24 ga. aluminized steel
Media: Dual layer microfine fiberglass
Separators: Hemmed-edge corrugated aluminum
Header Frame: 7/8” wide aluminized steel
Faceguards: Aluminized steel expanded
Cross Bracing: 1/2” “T” strap downstream and
horizontal strap upstream
Important Features
• Continuous duty up to 900ºF
• Aluminized steel construction
• 65%, 85%, 95% efficiencies
• Faceguards and grid straps
• MERV 11 to 14
Flanders Filters - Foremost in Air Filtration
Toll Free: 1-800-637-2803
Operating
Efficiency Limit ºF
Nominal Size
H x W x D (inch)
500 fpm
Rating
Media Weight
Area Each
cfm pd (sq. ft.) (lbs)
60-65%
750
900
24 x 24 x 12 2000
.45
24 x 12 x 12 1000 69 21
24 x 24 x 12 2000
.50
140 26
175 28
24 x 12 x 12 1000 90 22
80-85%
750
900
24 x 24 x 12 2000
.55
24 x 12 x 12 1000 69 21
24 x 24 x 12 2000
.60
140 26
175 28
24 x 12 x 12 1000 90 22
90-95%
750
900
24 x 24 x 12 2000
.65
24 x 12 x 12 1000 69 21
24 x 24 x 12 2000
.70
140 26
175 28
24 x 12 x 12 1000 90 22
Notes:
1. PD represents clean pressure drop in inches w.g. The recommended final pressure drop is 2.5 inch w.g.
2. Operation down to zero velocity is satisfactory for all models.
3. Efficiencies are average and are based on ASHRAE Standard 52.1 and 52.2 dust spot test methods.
Performance values stated may be averages typical of the products listed. Contact factory for actual performance test reports on specific products.
4. Perfmormance values shown in this publication may be averages or estimates intended to generally represent
product styles. Always contact factory for latest actual test data on specific Flanders Precisionaire models.
Guide Specifications
1.0 General
1.1 High temperature rigid filters shall be
PrecisionCell HT separator type as manufactured
by Flanders.
1.2 Filter sizes and temperature ranges shall be as
scheduled on the drawings.
2.0 Filter Construction
2.1 Filters shall be constructed by pleating a continuous sheet of wet-laid micro-fine glass media
into closely spaced pleats with hemmed-edge
corrugated aluminum separators.
2.2 The filter pack shall be sealed into a 24 ga.
aluminized steel frame with fire-retardant
sealant.
Flanders - PrecisionAire
Foremost in Air Filtration
Toll Free: 1-800-637-2803
2.3 Expanded metal aluminized steel faceguards
shall be installed on the air entering and air leaving sides.
2.4 A 1/2” “T” strap shall be installed on the downstream side and 1/2” horizontal strap on the air
entering side.
3.0 Performance
3.1 Initial and final resistance shall not exceed the
scheduled values.
3.2 Media area shall equal that of the scheduled
high temperature filter.
3.3 The manufacturer shall guarantee performance
as outlined in section 7.4 of ARI Standard 800.
REPRESENTED BY:
Loading...