Page 1
Intelligent Stick™
Intelligent Stick
TM
2.0 Plus
BD03 Series
Rev. A.0 Sep 2006
Page 2
Intelligent Stick™
Table of Contents
1. Introduction to Intelligent StickTM 2.0 Plus............................................................................... 1
2. Main Features Overview ………..……….....................……...…...……………………………...… 1
3. Hardware Specification ………………………………………….………….……………………..… 1
3.1 USB Interface ………………………….…..…………………..….........……………...……………… 1
3.2 NAND Flash Interface …………………………………………….……......……..…...………………. 1
3.3 OS Support ………………………………………………........…….......………..…...……………… 1
3.4 Product Capacity ……………………………………………………....….......………...……………. 1
4. Block Diagram ........................................................................................................................... 2
5. Absolute Maximum Ratings ..................................................................................................... 2
6. DC Characteristics .................................................................................................................... 3
7. Recommended Operating Conditions ..................................................................................... 3
8. Pin Assignments ....................................................................................................................... 3
9. Physical Specifications ............................................................................................................. 4
Rev. A.0 Sep 2006
Page 3
Intelligent Stick™
Revision History
Revision Date History Remark
A.0 09/08 ‘06 New Creation
y Important!! Please make sure the driver matches the part number on your pen drive before you download.
y Software AP System Requirements. One of following operation systems: Windows 98/98SE/Windows ME/Windows 2000/Windows XP
y The advertised memory capacity of this device represents unformatted capacity. Please note that once formatted and due to variations in
flash module block limitations, the functional storage space will be lower than the advertised capacity.
y “PQI reserves the right to make changes without notification when fit, form, function, quality and reliability are not affected. The data sheets do
not constitute contract documents and should not be considered part of the specification for purposes of any warranty.”
Rev. A.0 Sep 2006
Page 4
Intelligent Stick™
1. Introduction to Intelligent Stick
The Intelligent Stick Pro 2.0 Plus is a PQI patented technology. It combines characteristics of a flash card and a USB
flash drive. It does not need a card reader to read from or write to thus making it the perfect storage medium for all
types of digital devices. PQI's Intelligent Stick consumes minimum power and its minute dimensions makes it easy to
store. For added value, it also comes with password security, partitioning software and USB boot applications.
2. Main Features Overview
1. PQI’s patented Intelligent Stick™ interface USB 2.0 compatible
2. Multimedia or Data Storage
3. Hot swappable, USB Plug & Play compatible
4. Low power consumption
5. Its small size marking it easy to carry and store
6. Bundled software downloadable from PQI website : security and partition software
7. Carrying caddy for easy storage in your wallet
3. Hardware Specifications
USB Interface High-speed USB 2.0 interface; backward compatible with USB 1.1
NAND Flash Interface Integrated ECC circuits for 4-bit error correction
OS Support No drive is required for Windows ME, 2000, XP or Mac OS 9.x
TM
2.0 Plus
Environment
Temperature
Vibration
Shock resistant
Configuration
Capacity 128MBytes ~ 2GBytes
Reliability
MTBF(@25℃) 1,000,000 hours
Power Requirement
Voltage DC 3.3/5V ± 10%
Power Consumption
Read <100mA
Write <100mA
Standby <75mA
Operating 0℃ to 65℃
Non-Operating -20℃ to 75℃
Operating 0.2G
Non-Operating 15G
Operating 150G
Non-Operating 1000G
Un-configuration <75mA
Suspend <0.5mA
Rev . A.0 1/4 Sep 2006
Page 5
Intelligent Stick™
4. Block Diagram
Program ROM
8051 Micro
USB2.0
USB1.1
Host
USB2.0 or
1.1 Port
Controller
Data /
Address
Bus
USB 2.0
Interface
PLL, REG
CLK
PWR_GOOD
PWR_RST
Program RAM
DMA
EDC/
ECC
DA TA RAM
Flash
Control
Logic
Flash
Memory
5. Absolute Maximum Ratings
Symbol Parameter Min Max Unit
Tstorage Storage Temperature -20 75 ℃
Ta Ambient Operating Temperature 0 65 ℃
Vcc3 3.3V Supply Voltage -0.3 3.6 V
Vcc18 1.8V Supply Voltage -0.3 2 V
Vin3.3 3.3V Buffer Input Voltage -0.3 3.6 V
Vin3/5 3.3V/5V Buffer Input Voltage -0.3 5 V
Vin1.8 1.8V Buffer Input Voltage -0.3 2 V
Rev . A.0 2/4 Sep 2006
Page 6
Intelligent Stick™
6. DC Characteristics
Symbol Parameter Min. Max. Unit Notes
VDD Power Supply 3 3.3 3.6
VIH Input Voltage 0.9 X VDD -- 5
VIL Input Voltage -0.3 -- 0.2 X VDD
VOH Output Voltage VDD – 0.4 -- --
VOL Output Voltage -- -- 0.4
ILK Input leakage current -1 -- 1
IRW Working Current -- --
IOH IO output current -- 4 --
IOL IO output current -- 4 --
VIH Input Voltage 0.9 X VDD -- 5
7. Recommended Operating Conditions
Symbol Parameter Min. Typical Max. Units
Vcc33 Power Supply Voltage 3.0 3.3 3.3 V
Vin Input Voltage 0 Vcc Vcc+0.3 V
Vcc25 Internal Power Support 2.25 2.5 2.75 v
8. Pin Assignments
Pin No. Pin Name Function
1 VCC USB power input
2 USB D- USB differential signal
3 USB D+ The pairs are used to transmit Data/Address/Command
4 VSS Ground
123
4
Rev . A.0 3/4 Sep 2006
Page 7
Intelligent Stick™
9. Physical Specifications
9.1 Dimensions:
9.1.1 Height: 43mm
9.1.2 Width: 18mm
9.1.3 Depth: 2.8mm
9.1.4 Weight: 2.7g ± 0.5g
9.2 Outline of top view
Rev . A.0 4/4 Sep 2006
Loading...