Page 1
USB Flash Drive
Traveling Disk i161
BK07 Series
Rev. A.0 April 2008
Page 2
USB Flash Drive
Table of Contents
1. Introduction to Traveling Disk ………....................................................................................... 1
2. Main Features Overview …………..……….....................……...……………………………..…… 1
3. Hardware Specification ………………………………………..….………….……………………… 1
3.1 USB Interface ………………………………….………………….........……………………………… 1
3.2 NAND Flash Interface ……………………………………..…………..............………………………. 1
3.3 OS Support ………………………………………………….…………........………………………… 1
3.4 Product Capacity ………………………………………………..………….....………………………. 1
4. Block Diagram ........................................................................................................................... 2
5. Absolute Maximum Ratings ..................................................................................................... 2
6. DC Characteristics .................................................................................................................... 3
7. Recommended Operating Conditions ..................................................................................... 3
8. Pin Assignments ....................................................................................................................... 3
9. Physical Specifications ............................................................................................................. 4
Rev. A.0 April 2008
Page 3
USB Flash Drive
Revision History
Revision Date History Remark
A.0 04/29 ‘08 New Creation
Important!! Please make sure the driver matches the part number on your pen drive before you download.
Software AP System Requirements. One of following operation systems: Windows 98/98SE/Windows ME/Windows 2000/Windows XP
The advertised memory capacity of this device represents unformatted capacity. Please note that once formatted and due to variations in flash
module block limitations, the functional storage space will be lower than the advertised capacity.
“PQI reserves the right to make changes without notification when fit, form, function, quality and reliability are not affected. The data sheets do
not constitute contract documents and should not be considered part of the specification for purposes of any warranty.”
Rev. A.0 April 2008
Page 4
USB Flash Drive
1. Introduction to i161
The i161 gives you portability and security to offer you a peace of mind. Compatible with USB 2.0 / 1.1 specifications
with low power consumption and data protection.
2. Main Features Overview
♦ Mobile USB flash drive, USB 2.0 compatible
♦ Hot swappable, USB Plug & Play compatible
♦ LED indicator with three modes: Busy, waiting and off
♦ Multimedia and data storage
3. Product Specification
USB Interface High-speed USB 2.0 interface; backward compatible with USB 1.1 NAND Flash Interface Integrated ECC circuits for 4-bit error correction OS Support No drive is required for Windows ME, 2000, XP or Mac OS 9.x Environment
Temperature
Vibration
Shock resistant
Configuration
Capacity 1GBytes ~ 8GBytes
Power Requirement Voltage DC 3.3/5V ± 10% Power Consumption
Read <100mA
Write <100mA
Standby <100mA
Un-configuration <100mA
Suspend <1.0mA
Operating 0℃ to 65℃
Non-Operating -20℃ to 75℃
Operating 0.2G
Non-Operating 15G
Operating 150G
Non-Operating 1000G
Rev . A.0 1/4 April 2008
Page 5
USB Flash Drive
4. Block Diagram
Program ROM
8051 Micro
USB2.0
USB1.1
Host
USB2.0 or
1.1 Port
Controller
Data /
Address
Bus
USB 2.0
Interface
PLL, REG
CLK
PWR_GOOD
PWR_RST
Program RAM
DMA
EDC/
ECC
DA TA RAM
Flash
Control
Logic
Flash
Memory
5. Absolute Maximum Ratings
Symbol Parameter Min Max Unit
Tstorage Storage Temperature -20 75 ℃
Ta Ambient Operating Temperature 0 65 ℃
Vcc3 3.3V Supply Voltage -0.3 3.6 V
Vcc18 1.8V Supply Voltage -0.3 2 V
Vin3.3 3.3V Buffer Input Voltage -0.3 3.6 V
Vin3/5 3.3V/5V Buffer Input Voltage -0.3 5 V
Vin1.8 1.8V Buffer Input Voltage -0.3 2 V
Rev . A.0 2/4 April 2008
Page 6
USB Flash Drive
6. DC Characteristics
Symbol Parameter Min. Typical Max. Units
VDD Supply voltage for VCC3 or VCC3A
Regulator output voltage for VCC or
VDD18
VCCA
VIL Input Low Voltage
VIH Input High Voltage
VOL Output Low Voltage (IOL=4mA)
VOH Output High Voltage (IOH=4mA)
CIN Input pin capacitance
IDD Supply current
ISUS Suspend current (D+1.5KΩ)
3.0 3.3 3.6
1.62 1.8 1.98 V
-0.5 0.8 V
2.0 V
0.4 V
2.4 V
10
50 mA
300 uA
7. Recommended Operating Conditions
Symbol Parameter Min. Typ. Max. Units
VCC33 3.3V Supply Voltage 3.0 3.3 3.6 V
USBVIN USB 5V Supply Voltage 4.5 5 5.5 V
VCC18 1.8V Supply Voltage 1.6 1.8 2 V
8. Pin Assignments
V
pF
Pin No. Pin Name Function
1 VCC USB power input
2 USB D- USB differential signal
3 USB D+ The pairs are used to transmit Data/Address/Command
4 VSS Ground
123
4
Rev . A.0 3/4 April 2008
Page 7
USB Flash Drive
9. Physical Specifications
9.1 Dimensions:
9.1.1 Height: 40.49 mm±0.1mm
9.1.2 Width: 17.70 mm±0.1mm
9.1.3 Depth: 6.10 mm±0.1mm
9.1.4 Weight: 8.5mm
9.2 Outline of top view
± 0.5g
Rev . A.0 4/4 April 2008
Loading...