PPA DZ HOME, DZ HOME BLDC, DZ HOME JET FLEX Technical Manual

MOTOPPAR INDÚSTRIA E COMÉRCIO DE AUTOMATIZADORES LTDA.

A

v. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial
CEP 17400-000 - Garça - SP - Brasil
Fone / Fax: [phone]
www.ppa.com.br

TECHNICAL MANUAL

DZ HOME

Warning:
Do not use the
product without
first reading the
instruction

INDEX

Important safety instructions ............................................................................. 3

Technical characteristics ................................................................................... 4

Tools required for installation .............................................................................5

Electrical installation .......................................................................................... 5

Care with the electrical installation .................................................................... 6

Care with the gate before operator ...................................................................7

Installing and fixing the operator ....................................................................... 8

Equipment dimensions ...................................................................................... 8

Analog limit switch installation ...........................................................................13

Maintenance ...................................................................................................... 16

2

IMPORTANT SAFETY INSTRUCTION

Recommendation:

For the installation of the equipment, it is important that the specialized
installer follow all the instructions quoted in this TECHNICAL MANUAL
and in the USER MANUAL.

With the USER MANUAL, the installer must present all information,
uses and safety items of the equipment to the user.

Before using the DZ NEW HOME ANALOG OPERATOR, read and
strictly follow all the instructions contained in this manual.

- Before installing the operator system, make sure that the local
electrical network is compatible with the one required on the
equipment identification label;

- Do not connect the mains until installation / maintenance is complete.
Always make electrical connections to the board with the mains
switched off;

- After installation, make sure that the parts of the gate do not extend
through the roads and public promenade;

- It is mandatory to use full shutdown devices in the operator system.

3

TECHNICAL CHARACTERISTICS

DZ HOME

OPERATOR TYPE SLIDING SLIDING SLIDING

RATED VOLTAGE 220 V 220 V 127 V

NOMINAL FREQUENCY 60 Hz 50 Hz 60 Hz

RATED POWER 460 W 470 W 335 W

MOTOR ROTATION 1740 rpm 1455 rpm 1740 rpm

NOMINAL CHAIN 2,15 A 2,37 A 2,86 A

REDUCTION 1:24 1:24 1:24

LINEAR SPEED 16,4 m/min 13,7 m/min 16,4 m/min

PERFORMANCE 30 cycles/h 30 cycles/h 30 cycles/h

DEGREE PROTECTION IPX 4 IPX 4 IPX 4

TEMPERATURE RANGE -5° C / +50° C -5° C / +50° C -5° C / +50° C

ISOLATION TYPE Class B, 130 ° C Class B, 130 ° C Class B, 130 ° C

LIMIT SWITCH ANALOG ANALOG ANALOG

DZ HOME JET FLEX / DZ HOME BLDC

OPERATOR TYPE BLDC SLIDING JET FLEX SLIDING

RATED VOLTAGE 220 V / 127 V 220 V / 127 V

NOMINAL FREQUENCY 60 Hz 60 Hz

RATED POWER 100W / 130W 100W / 130W

MOTOR ROTATION 4500 rpm 4365 RPM

NOMINAL CHAIN 0,7A / 1,4A 2,75 A / 3,6 A

REDUCTION 1:22 1:22

LINEAR SPEED 36 m/min 41 m/min

PERFORMANCE 100 cycles/h 40 cycles/h

DEGREE PROTECTION IPX 4 IPX 4

TEMPERATURE RANGE -5° C / +50° C -5° C / +50° C

ISOLATION TYPE Class B, 130 ° C Class B, 130 ° C

LIMIT SWITCH Hybrid Hybrid

MAX. MASS FROM THE
GATE LEAF

MAXIMUM DIMENSION;
GATE

HEIGHT = 2,5 m LENGTH

400kg 400kg

HEIGHT = 2,5 m LENGTH

= 3,0 m

= 3,0 m

4

TOOLS REQUIRED FOR INSTALLATION

Here are some tools required to install the operator:

PLIERS

LADDER

WELDING MACHINE HAMMER LEVEL TAPE MEASURE

SAWING BOW SOCKET WRENCH SCREWDRIVER NUT WRENCH

FRAME DRILL PENCIL SANDER

ELECTRICAL INSTALLATION

For electrical installation, the network shall contain the following characteristics:

- Electric network 127V or 220V;

- Have 5A circuit breakers in the electrical distribution box;

- 3/4 "diameter conduit between the electrical distribution box and the total
disconnect device;

- 3/4 "diameter conduit between the total shut-off device and the operator
connection point;

- 1/2 "diameter conduits for buttonhole, external and optional;

- 1/2 "diameter for safety photocells (optional).

- The cable for the fixed wiring must comply with NBR NM 247-3;

-The power conductor of a product for internal use must be a
flexible cable 3 x 0.75 mm²; 500 V, according to the norm NBR
NM 247-5;

-The power conductor of a product for external use must be a
3 x 0.75 mm² flexible cable; 500 V, according to IEC 60245-57.

5