Page 1
OPERATOR’S MANUAL & PARTS LIST
https://harrissupplyind.com - To Order Parts Call 608-268-8080
Commercial Dryer/Air Mover
Standard Models
PD350, PD500, PD750, PD500DX, PD750DX
Save These Instructions
WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL
COMPLETELY BEFORE OPERATING THIS EQUIPMENT.
©
Tacony, Inc., All rights reserved
X8691-Man 4/2015
Page 2
important safety instructions
https://harrissupplyind.com - To Order Parts Call 608-268-8080
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE
When using an electrical appliance, basic
precautions should always be followed.
WARNING- To reduce the risk of fire, electric
shock or injury:
Use only as described in this manual. Use
only manufacturer’s recommended
components and attachments.
Use only indoors. Do not use outdoors or
expose to rain.
Do not use with damaged cord or plug. If
appliance is not working as it should, has
been dropped, damaged, left outdoors, or
dropped into water, return it to your Authorized
Powr-Flite dealer.
Do no pull or carry by cord, use cord as
a handle, close door on cord, or pull cord
around sharp edges or corners. Keep cord
away from heated surfaces.
Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
Do not handle plug or appliance with wet
hands.
Do not put any object into openings. Do not
use with any opening blocked; keep free of
dust, hair and anything that may reduce air
flow.
Turn off all controls before unplugging.
Do not attempt to service the unit while
appliance is plugged in.
Appliance may cause a fire when operating
near flammable vapors or materials. Do not
operate this machine near flammable fluids,
dust or vapors.
Connect to a properly grounded outlet.
Use only on GFCI protected receptacles.
To reduce the risk of electric shock, connect
only to an outlet provided with a ground fault
circuit interrupting device.
Do not route cord under furniture or
appliances
Do not use an extension cord with
this fan.
This unit is thermally protected.
WARNING
Do not stack dryers
more than two units
high without tie-downs
GroundinG instructions
This appliance must be grounded. If it should malfunction or break down, grounding
provides a path of least resistance for electric current to reduce the risk of electric
shock. This appliance is equipped with a cord having an equipment-grounding
conductor and grounding plug. The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance with all local codes and
ordinances.
This appliance is for use on a nominal 120 volt circuit and has a ground plug (see
illustration, right). Make sure that the appliance is connected to an outlet having the
same configuration as the plug. No adaptor should be used with this appliance.
WARNING - Improper connection of the equipment-grounding conductor can result
in a risk of electric shock. Check with a qualified electrician or service person if you
are in doubt as to whether the outlet is properly grounded. Do not modify the plug
provided with the appliance – if it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
for Best performance
• Keep machine clean and in good operating condition.
• Have machine checked periodically by your Authorized
Powr-Flite Dealer.
• Store machine carefully in dry area.
• For optimum drying performance and safety, study and
follow your operators manual.
Grounded
Outlet
Prong or
Grounding pin
Grounded
Outlet Box
• Use only authorized service centers for parts or service.
SAVE THESE INSTRUCTIONS
Page 3
operatinG instructions
https://harrissupplyind.com - To Order Parts Call 608-268-8080
Plug in to a standard outlet with the correct voltage and
amperage for the unit.
Place the dryer in the desired operating position.
Set the switch at the desired speed: low, medium or high.
Check for proper operation before leaving the unit unattended. Do not move or carry the dryer when it is running.
3 postion switch
maintenance/trouBle shootinG
Periodic Maintenance
1. Check power cord for any breaks, seperations or cuts.
2. Make sure the ground pin or grounding prong is intact or
the machine will be unsafe to operate.
cord wrap
unit in vertical position
Trouble Shooting (if the dryer will not run)
1. Check electrical cord; is it firmly seated in wall outlet
2. Check GFCI and reset if tripped
3. Check to see if building circuit breaker is tripped. If circuit
is overloaded, move cord to different GFCI outlet.
4. Make sure power cord is firmly connected and is in
good condition.
Page 4
Models PD350, PD500, PD750 PARTS
https://harrissupplyind.com - To Order Parts Call 608-268-8080
5
4
10
11
6
26
3
2
7
8
1
25
9
16
15
18
17
24
14
12
20
19
23
13
21
22
Parts for PD350, PD500, PD750
ref# part # description
1 X8876REPRO Dryer Housing, Black , Regrind
2 PD5D Squirrel Cage, Plastic
3 X8872A Intake Panel
4 X8261 Screw, #6 x 1/2”, Black
7 X8868-D 3/4 hp Dryer Motor
7 X8882-D 1/3 hp Dryer Motor
7 X8881-D 1/2 hp Dryer Motor
8 X8875 Motor Control Panel
9 X8903 Screw M4x6 Flat Head Phillips
10 X9831 Knob, Switch
11 X8261 Screw, #6 x 1/2”, Black
12 X8008N Nut, Lock, 1/2” Steel Conduit
13 PD8 Strain Relief
ref# part # description
14 X8926 20’ HD 3 Wire Cord 16/3
15 X8897 Switch, 3 Speed
16 X8964 Screw 3/8-16 x 1/2” Hex Head
17 X8871 Grill, Dryer Discharge
18 X8256 Nut 8-32 KEPS
19 PX73 Screw, 8-32 x 1 PHIL PAN
20 X8929 Foot, Left Dryer Kickstand
21 X8261 Screw, #6 x 1/2”, Black
22 X8874 Kickstand, Dryer
23 X8928 Foot, Right Dryer Kickstand
24 PD3B Foot, Black Rubber
25 X8946 Rivet, 3/16 Black
Page 5
Models PD500DX, PD750DX PARTS
https://harrissupplyind.com - To Order Parts Call 608-268-8080
ref # item # description
1 X8876REPRO dryer housing black
2 PD5D squirrel cage plastic
3 X8872A intake panel
4 X8261 screw #6 x 1/2 pan hd phil
5 X8990 handlewheel assembly
6 X8226 1/4-20 x 1" hex head cap screw
7 X8881-D dryer motor w/cap 1/2 hp motor 120V PD500DX
7 X8868-D dryer motor w/cap 3/4 hp motor 120V PD750DX
8 X8875 motor control panel
9 X8903 screw, m4x6 flat head phillips
10 X9831 knob
11 X8261 screw #6 x 1/2 pan hd phil
12 X8008N nut, lock, 1/2" steel conduit
13 PD8 strain relief 1/2" npt
14 X8926 16/3 SJTW 20' cord rev 2 yellow
ref # item # description
15 X8897 switch
16 X8964 screw 3/8-16 x 1/2
17 X8871 dryer grill
18 X8256 nut 8-32 keps zinc
19 PX73 8-32 x 1 phil pan m/s
20 X8929 left kickstand foot
21 X8261 screw #6 x 1/2 pan hd phil
22 X8874 kickstand
23 X8928 right kickstand foot
24 PD3B dryer foot PD500DX
24 PD3C dryer foot PF750DX
25 X8946 bulbex rivet 3/16 x .040-.354
26 7BF004 nut kep 1/4-20 zinc
*call for pricing and availability of all referenced parts
Page 6
WARRANTY
https://harrissupplyind.com - To Order Parts Call 608-268-8080
The manufacturer warrants to the original purchaser that products manufactured are free from defects,
provided such goods are installed, operated and maintained in accordance with written manuals or other
instructions for a period of 1 year from date of purchase on workmanship, motor, and parts. In case you,
as our customer, meet any trouble with your machine, contact a Powr-Flite representative, who will be
happy to be of service to you and will take care of any warranty issues. This warranty covers normal
use and does not cover damage which occurs in shipment or failure resulting from altercation, accident,
misuse, abuse, neglect or improper maintenance.
A Tacony Company
3101 Wichita Court • Ft. Worth, TX 76140-1755
1-800-880-2913 • Fax: 1-817-551-0719 • www.Powr-Flite.com
X8691-Man 4/2015
©Powr-Flite, All Rights Reserved
Loading...