Standard and High Speed Floor Machines
P201, P171, P131, 175 RPM P201HD, P171HD,175 RPM P202, P172, 175/320 RPM
Standard Speed Standard Speed Heavy Duty Dual Speed
P203, P173, 300 RPM P171SD, 175 RPM
High Speed Sander
U.S. Patent Number 4,756,042 • U.S. Patent Number 296,251
Operator’s Manual
A Tacony Company
3101 Wichita Court • Ft. Worth, TX 76140-1710
x8444
Your new Powr-Flite®Floor Machine will afford you many years of trouble-free operating satisfaction provided
it is given proper care. Prior to packaging, your Powr-Flite
®
Floor Machine was inspected by a Quality Control
Technician.
P201, P171, P131, 175 RPM P201HD, P171HD,175 RPM P202, P172, 175/320 RPM
Standard Speed Standard Speed Heavy Duty Dual Speed
P203, P173, 300 RPM P171SD, 175 RPM
High Speed Sander
UNCRATING
Your Powr-Flite®Floor Machine was protectively packed to
prevent damage in shipment. We suggest that upon removing the
unit from its carton, you carefully inspect it for any possible
damage in transit. If damage is discovered, immediately notify the
transportation company who delivered your machine. As a manufacturer, we are unable to act upon any claim for concealed
damage; you must originate the claim.
IMPORTANT SAFEGUARDS
This machine is designed to be safe when used to perform the
functions specified in this Operator’s Manual. Should damage
occur to electrical or mechanical parts, the machine should be
repaired by the manufacturer or competent service station before
using in order to avoid further damage to the machine or physical
injury to user. Your floor machine is equipped with a safety switch
lockout device designed for your safety . Do not attempt to bypass or
defeat the safety lockout device. Never use any device to lock the
power switch triggers in the ON position.
WARNINGS
READ THIS OPERATOR’S MANUAL!
WARNING: Y ou must have training in the operation of this machine
before using it.
WARNING: Machines can burn flammable materials and vapors.
Do not use this machine with or near fuels, grain dust, solvents,
thinners or other flammable materials.
WARNING: Do not operate this machine unless it is completely
assembled.
WARNING: Do not use this machine as a step or to move furniture.
WARNING: When disconnecting power cord from electrical outlet,
grasp the plug. Pulling it out by the cord itself can damage cord
insulation and internal connection to plug. To prevent electric
shock, always remove the electrical plug from the electrical outlet
before doing any repairs or maintenance to this machine.
WARNING: To prevent injury, always remove the electrical plug
from the electrical outlet before changing the polishing pad and
before leaving the machine.
WARNING: To prevent injury, keep hands, feet and loose clothing
away from the rotating pad.
WARNING: Maintenance and repairs must be done by authorized
personnel only.
WARNING: Keep all fasteners tight. Keep adjustments according to
specifications.
WARNING: Keep the electrical parts of the machine dry. For
storage, keep the machine in a building.
WARNING: Always use a three-wire electrical system connected to
the electrical ground. For maximum protection against electric
shock, use a circuit that is protected by a ground fault circuit interrupter. Consult with your electrical contractor.
WARNING: To prevent damage to the power cord, do not let the
pad, pad driver or wheels touch the power cord when the machine
is running. Always lift the power cord over the machine.
WARNING: Make sure all labels, decals, warning, cautions and
instructions are fastened to the machine.
APPLICATIONS FOR FLOOR
MACHINE (MODELS P201, P171,
P201HD, P171HD and P131)
175 RPM ONLY
The Powr-Flite®175 RPM floor machine will operate in a wide
variety of applications. The 175 RPM floor machine is the most
versatile speed in the floor care industry.
APPLICATIONS OF 175 RPM
STANDARD SPEED FLOOR
MACHINES ON HARD FLOORS
•Spray buffing with a Powr-HD™ red spray buff pad and spray
buff chemical, such as Powr-Glo
®
.
•Dry buffing a buffable finish with a Powr-HD™ tan, beige or
white pad or Powr-Luster™ brush.
•Scrubbing with a Powr-HD™ green or blue pad or scrubbing
brush, such as Powr-Scuff™.
•Stripping with a Powr-HD™ black pad and a stripping chemical, such as Powr-Up
®
.
APPLICATIONS OF 175 RPM STANDARD SPEED FLOOR MACHINES
ON CARPET
•Bonnet cleaning with a Powr-Sorb™ yarn bonnet and carpet
maintainer chemical, such as Spin-Away
®
.
•Shampooing using a showerfeed shampoo brush and solution
tank mounted to the hand containing carpet shampoo.
APPLICATION OF POWR-FLITE
®
HEAVY DUTY 175 RPM
FLOOR MACHINES
(MODELS P201HD and P171HD)
The heavy duty standard speed floor machine may be used for spray
buffing, dry buffing, scrubbing and stripping applications.
These heavy duty floor machines are specially recommended for
long term aggressive scrubbing and stripping maintenance.
The P201HD & P171HD heavy duty floor machines are specially
recommended for the following applications:
•Scraping with an attachment such as the Powr-Flite®Scrape-
Away
®
tool to remove heavy industrial deposits and residue or
to prepare a foundation for installation of carpet.
•Wire brushing of concrete floors.
•Sanding with very aggressive sandpaper or sand screen discs.
•Carpet restoration where shampooing & pile lifting require very
stiff brush bristles.
WARNING
To prevent injury, always remove the electrical plug from the
electrical outlet before changing the polishing pad and before
leaving the machine.
PREPARE THE MACHINE
FOR OPERATION
To attach the drive block or brush or other attachment, be sure the
handle is “locked” in the upright position (See picture #1). Lay
the floor machine on its back with the handle lying on the floor , this
exposes the driving plate on the underside of the floor machine.
Holding the drive block, brush or attachment in both hands and
straddling the motor with your back to the handlebox, bend over
and fit the three slots of the clutch plate (build into the back of the
brush) over the three lugs of the driving plate. T urn the drive block,
brush or attachment counter-clockwise as far as it will go until it is
seated in the ready-to-use position. (See picture #2)
CAUTION: This is the only proper way to install a drive block,
brush or attachment. NEVER put a drive block, brush or attachment on the machine by placing it on the floor and moving the
running machine over it, or by placing the machine over the block
or attachment and then starting the motor.
Return the floor machine to upright position and adjust handle to
operating position. Recommended handle position is close to the
waist with arms extended down. Lock the cam release lever into
position.
NOTE: The hardened steel cam release lever does not require
extreme tightening to effectively hold the handle in position.
Over-tightening will shorten the functional life of the lever. To
remove drive block, brush or attachment: Lay the floor
machine on it’s back again and disengage clutch plate slots
from driving plate lugs by turning clockwise.
HOW TO OPERATE THE MACHINE
Withthedrive block and pad,brush or attachment intheready-to-use
position, the handle locked at the desired operating height, and the
electriccable pluggedin,placehandsonthe handlegripsandsqueeze
the switch triggers beneath the handle grips. (See picture #3)
This activates the motor and starts the block, brush or attachment in
operation. CAUTION: When leaving the machine unattended,
disconnect the wall plug and return the handle to the “locked”
upright position to prevent accidental starting.
TO GUIDE YOUR FLOOR MACHINE
To Right: raise handle slightly. The higher the handle is lifted, the
faster the machine will move to the right.
To Left: to change direction, lower the handle until the machine
travels to the left. The more the handle is lowered, the faster the
movement to the left.
TO INSTALL THE OPTIONAL
SOLUTION TANK
Mount the solution tank to the front of the handle and attach with
mounting brackets and knobs. Position the solution tank control
handle horizontally and below the switch lever of the machine and
adjacent to the right handle grip.
Remove the plug from the motor housing and insert the (long)
extension tube adaptor and secure at bottom of machine with the
retainer. The solution tank should be used only with a showerfeed
drive block or brush.
Picture #1
Picture #2
Picture #3
Switch Trigger
APPLICATION OF THE HIGH SPEED
300 RPM FLOOR MACHINES
(MODELS P203 and P173)
Spray Buffing to revitalize an existing floor finish to a “wet look”
shine especially in heavy traffic areas using a Powr -HD™ yellow or
natural hoghair blend pad.
Dry Buffing with a brush on uneven floors coated with a buffable
finish or with a Powr-HD™ tan, beige or white pad on even floor
surfaces.
OPERATIONS OF THE HIGH SPEED
300 RPM
(MODELS P203 and P172)
Follow the same operation procedures described for 175 RPM
machines.
APPLICATION OF THE DUAL SPEED
175/320 RPM MACHINES
(MODELS P202 and P172)
The Powr-Flite®dual speed machines will operate in a broad
range of applications. These machines perform all the applications
of the 175 RPM standard speed machines and the 300 RPM high
speed machines except the specialized applications.
Do not use dual speed machines for sanding, grinding or
scraping.
The dual speed machines are specially designed for spray cleaning
of heavy traffic areas.
OPERATION OF THE DUAL SPEED
MACHINES
Followthe operation procedures described for175 RPM machines.
The proper speed selection is important to properly operate these
machines. Speed selection Low (175 RPM) or High (320 RPM)
is made with the switch located on the base and motor housing.
(See Picture #4)
Stripping, scrubbing, bonnet cleaning and shampooing should be
performed at 175 RPM Low Speed.
Spray buffing and dry buffing should be performed at 320 RPM,
High Speed.
Spray cleaning is a two speed maintenance operation. Apply a
spray buff chemical such as Powr-Glo
®
to the floor ahead of the
machine. Make the first passes through the spray buff at low
speed with an open weave pad such as the Powr-HD™ blue
cleaner pad or the brown hoghair blend spray cleaner pad.
Remove the spray cleaning pad and place a buffing pad on the
machine such as Powr-HD™ yellow, beige or natural hoghair
blend pads.
Switch the speed to High 320 RPM and buff the dulled finish to a
high gloss.
Unplug the power cord and wrap it under the cord hook and over
the right handle grip. Clean the cord off to prevent heavy soiling
and cleaning residues from building up on the cord. This is a
good time to inspect the cord for cuts, gashes and loose prongs.
Tip the machine back and remove the pad and the drive block or
brush.
Picture #4
The condition of the floor pad or brush has a direct affect on the
performance of your floor machine. When the pad becomes dirty ,
turn it over and use the other side. When finished, wash the pad
or brush and allow it to dry completely before using it again.
Stand the wet brush on the bristles until dry, then hang up the
brush.
Do not store the machine with the drive block, pad or
brush on the machine.
Wipe off the machine housing and wheels to prevent build-up of
unnecessary residue.
TRANSPORTING THE MACHINE
Place the handle in the upright position. Lock the handle cam
release lever. Tip the machine back and transport on the wheels.
MAINTENANCE FOR THE P201,
P203, P171, P173, P131, P201HD,
P171HD, P202
and P172
Onceamonthremovethemotorcoverof the unplugged machine by
pullingevenly ,butfirmly,withbothhandsuntilthecover is removed.
Vacuumoutanydustor debris which hasaccumulatedonthemotor .
Replace the motor cover by setting it over the holes in the housing and firmly pushing it down.
Check and maintain the tightness of all the fasteners.
WARNING:Do not over-tighten the switch housing screws.
Keep the machine clean especially at the handle tube and collar
so the handle tube will move freely through the collar.
Inspect the cord for cuts, gashes, or loose prongs; replace as
needed.
Disassembly of this motor voids the warranty. Improper
disassembly and assembly of this motor can permanently damage
the field or rotor.
For P202 & P172 only:The length of the carbon brushes should
be inspected annually . If they are no longer extended past the holder window, they should be replaced. Replacement of the carbon
brushes should only be done by a qualified service technician.
Speed Switch
TROUBLESHOOTING
Machine does not run.
The circuit breaker has tripped. Allow the circuit breaker 2 minutes
to cool before resetting.
Plug is broken or has loose contact. Replace.
Prevent circuit overload.
Check the pad and change it if it is rough or dirty.
Spray buffing or spray cleaning is not a substitute for scrubbing or
mopping a floor. Prepare the floor surface before spray buffing.
Eliminate any extension cord that is smaller than 12/3 wire or
greater than 25 feet in length.
Unplug anything other than the machine from the circuit or locate
another circuit.
Machine will not start.
Circuit breaker is not reset. Reset breaker.
Plug is broken or has a loose contact. Replace.
Circuit breaker is defective or weak. Replace.
Switch is defective. Replace switch.
Rectifier is defective. Replace rectifier (P202 and P172 only).
Machine will not reach operating speed.
Unplug anything else other than the machine from the circuit or
locate another circuit.
Motor runs but pad or brush does not turn.
Coupling is broken. Replace. Coupling is not covered under warranty. Do not attempt to place a running machine over a block or
brush. Always place and remove the block or brush by hand.
WARNING
TO AVOID FIRE, DO NOT USE WITH A FLAMMABLE
OR COMBUSTIBLE LIQUID TO CLEAN FLOOR.
X8444
ONE LAST REMINDER! READ ALL INSTRUCTIONS,
WARNINGS AND CAUTIONS BEFORE USING EQUIPMENT.
These guidelines are presented for your protection and convenience. Please read them carefully, since a failure to heed these precautions
could result in discomfort or injury. When using an electrical appliance, basic safety precautions should always be followed.
SAFETY INSTRUCTIONS
This Floor Machine should be grounded while in use to protect the
operator from electric shock. This machine is equipped with a 3conductor cord and a 3-prong grounded type attachment cap plug
to fit the proper grounding type receptacle. The green (or green
and yellow) conductor in the cord is the grounding wire. Never
connect this wire to anything other than the grounding blade.
The Floor Machine is provided with an attachment cap plug, as
shown in Sketch A, and is intended for use on a nominal 120 volt
circuit. If a properly grounded receptacle, as shown in Sketch A, is
unavailable, an adaptor, as shown in Sketch C, is available and
should be installed, as shown in Sketch B, if the outlet box that
houses the receptacle is grounded. Be sure to fasten the grounding
tap to the faceplate screw.
© 2000 Tacony, Inc, All Rights Reserved
A Tacony Company
3101 Wichita Court • Ft. Worth, TX 76140-1710
Powr HD
™
Pads
The Finest Quality, Heavy Duty Floor Pads Available!
Nylon Blend Thick Pads • Polyester Blend Thick Pads • Hoghair Pads
All Thin Pads Packed 10 Pads Per Case • All Thick Pads Packed 5 Pads Per Case
Pads Sold By The Case Only • Cases Can Be Assorted To Obtain Quantity Pricing.
Black Strip Pad
Nylon Blend
For heavy-duty wet stripping. Very aggressive agent embedded
throughout pad. Removes old wax build-up. Cleans down to
original surface.
Brown Strip Pad
Polyester Blend
For heavy-duty wet or dry stripping. Very aggressive agent
embedded throughout pad. Removes old wax build-up. Cleans
down to original surface.
Red Spray Buff Pad
Polyester Blend
For spray-buffing and light scrubbing. Mild aggressive agent
embedded throughout pad. Removes light scuff marks and dirt
while producing a smooth shining finish.
Tan Buff Pad
Nylon Blend
For buffing and light wet scrubbing. Mild aggressive agent
embedded throughout pad. Removes light scuff marks and dirt
while producing a smooth, shining finish.
Blue Cleaner Pad
Polyester Blend
For heavy-duty scrubbing or light stripping, wet or spray.
Aggressive agent embedded throughout pad. Removes heavy
dirt and scuff marks without removing waxed finish.
Green Scrub Pad
Nylon Blend
For heavy-duty scrubbing or light stripping, wet or spray.
Aggressive agent embedded throughout pad. Removes heavy
dirt and scuff marks without removing waxed finish.
Yellow High Speed Spray Buff Pad
Polyester Blend
For spray buffing when using a high speed buffing machine.
Light aggressive agent in pad. Specially designed for use with
high speed floor machines for an extra high gloss finish.
Beige Ultra High Speed Spray Buff Pad
Polyester Blend
Specially designed when using an ultra high speed floor
machine (1200 to 2000 RPM). Mild aggressive agent in pad for
light cleaning and super polishing.
Green Stripping Pad
Hoghair Blend
Heavy-duty aggressive agent embedded throughout pad for
removing old floor finish.
Brown Spray Cleaner Pad
Hoghair Blend
Aggressive agent embedded in pad for unsurpassed cleaning.
Natural High Speed Spray Buff Pad
Hoghair Blend
Produces a wet look shine of unequaled brilliance when spray
buffing.
White Super Polish Pad
Polyester Blend
For polishing No aggressive agent in pad. Extra fine pad for
producing high luster finish.
Loading...