Power Wheels Chevrolet Silverado 74310 Owner's Manual With Assembly Instructions

Owner’s Manual with Assembly Instructions
Please read this manual and save it with your original sales receipt.
For Model 74310
Tools needed for assembly:Phillips Screwdriver and Hammer (tools not included).
Use only with a Power Wheels®12 Volt Lead-Acid Rechargeable Battery and a Power Wheels®12 Volt Charger with Type “12V” Connector (both included).
Chevrolet, Chevy, The Bow Tie, Silverado emblems are General Motors trademarks
used under license to Fisher-Price, Inc.
Goodyear (and winged foot design) and Wrangler (for tires) are trademarks of
The Goodyear Tire & Rubber Company, used with permission.
Product features and decoration may vary from the picture above.
®
IDFP0899
2
Table of Contents
Important Information
A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
B Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
D Parts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
E Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
F Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
G Label Decoration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
H Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
I Battery Care and Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
J Rules for Safe Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
K How to Operate Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
L Caring for Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
M Problems and Solutions Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
N Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
O Authorized Service Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
• Your new vehicle requires adult assembly.Please set aside at least 45 minutes for assembly.
• You must charge your battery for 18 - 30 hours before you use your vehicle for the first time. We recommend that you start charging your battery before beginning assembly. Please see Batter y Charging beginning on page 7 for detailed instructions.
• Read this manual carefully for important safety information and operating instructions before using your vehicle.Keep these instructions for future reference as they contain important information.
• This vehicle is designed for use on grass, asphalt or other hard surfaces; on generally level terrain; by children 3 years of age and older.
• Make sure children know and follow these rules for safe driving and riding:
- always sit in the seat.
- always wear shoes.
- only two (2) riders at a time.
• This vehicle has adjustable play seat belts. Please note that the adjustable seat belts are designed to be a play feature only and do not function as protective safety restraints.
• To prevent damaging the motors and gears, do not tow anything behind the vehicle or overload it. Do not exceed the maximum weight capacity of 130 lb.(60 kg).
• For safety reasons, your vehicle has been pre-set so that it will only operate at low speed. You must remove
the high speed lock-out screw to allow operation of the vehicle at high speed. Please see page 22 for
detailed instructions.
A
• If you have any questions about your Power Wheels
®
vehicle, please call our toll-free service lines at 1-800-348-0751 from 8 AM to 6 PM (EST) Monday through Friday.Trained customer service representatives are available to take your call in English or French. Habla Español? Si usted tiene alguna pregunta ó necesita asistencia llame gratis 1-800-348-0755 para los Estados Unidos.Tenemos representantes que hablan español para atender su llamada.
• For your convenience, Power Wheels®maintains an Authorized Service Center Network with more than 400 authorized service centers nationwide. Our authorized service centers will repair or replace par ts under warranty at no extra charge, and can perform non-warranty repairs for a minimal charge. Please see the Authorized Service Center list beginning on page 28 to find the authorized service center nearest you, or call 1-800-348-0751.
• Please complete and return the enclosed Registration Card today, or call 1-800-348-0751 to register your vehicle by phone.
3
Warnings and Cautions
B
CA UTION
• In the unassembled state, this package contains small parts. Adult assembly is required.
• Use the charger in dry locations only.
WARNING
Prevent Injuries and Deaths
• Direct Adult Supervision Required
• Keep Children Within Safe Riding Areas. These areas must be:
- away from swimming pools and other bodies of water to prevent drownings
- generally level to prevent tipovers
- away from steps, driveways, roads and alleys.
RIDING HAZARD
WARNING
• Battery can fall out and injure a child if vehicle tips over. Always use battery clamp.
PREVENT FIRE
- Never modify the electrical system.Alterations could cause a fire resulting in ser ious injury and could also ruin the electr ical system.
- Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury.
- Use of Power Wheels®components in products other than Power Wheels®vehicles could cause overheating, fire or explosion.
• The battery must be handled by adults only.The battery is heavy and contains sulfuric acid (electrolyte). Dropping the battery could result in ser ious injur y.
• Never allow children to charge the battery. Battery charging must be done by adults only. A child could be injured by the electricity involved in charging the batter y.
• Never lift or carry the battery by the wires or connector.This can damage the battery and possibly cause a fire resulting in serious injury. Lift and carr y the batter y by the case only.
• Read the safety instructions on the batter y.
• Examine the battery, charger and their connectors for excessive wear or damage each time you charge the battery. If damage or excessive wear is detected, do not use the charger or the battery until you have replaced the worn or damaged part.
HOT motors.Handle carefully.
ELECTRICAL HAZARD
Parts
C
4
• If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store.
• Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded.
• Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal par ts with a paper towel to remove any excess lubricant.
Steering Column
Running Board - 2
Hood
Cab
Seat
Antenna
Steering Wheel Cap
Vehicle Body
Steering Wheel
5
Parts
Not Shown: Label Sheet - 3
All Shown Actual Size
.354 Cap Nut - 2*
*For your convenience, an extra #8 x 3/4" screw and an extra .354 cap nut have been included.
#8 - 18 x 1" Screw – 2
#8 - 18 x 13/4" Screw – 2
#8 x 3/4" Screw – 11*
Knob Plate
Dashboard Knob – 2
Key Assembly
Microphone
Gas Cap
Short Seat Belt Strap - 2
12 V olt Charger
Long Seat Belt Strap
12-VOLT
CHARGER
12 V olt Battery
Pb
Battery Clamp Cap
Wire Clip
6
Parts Diagram
D
23
Pb
4
5
6
18
18
17
20
19
14
22
12
13
8
9
16
11
7
2
3
24
15
15
21
19
19
10
1. Vehicle Body
2. Running Board - 2
3. Steering Column
4. Hood
5. 12 V olt Battery
6. Cab
7. Antenna
8. Steering Wheel
9. Steering Wheel Cap
10. Knob Plate
11. Dashboard Knob - 2
12. Key Assembly
13. Microphone
14. Long Seat Belt Strap
15. Short Seat Belt Strap - 2
16. Seat
17. Gas Cap
18. .354 Cap Nut - 2
19. #8 x 3/4" Screw - 11
20. #8 - 18 x 1" Screw - 2
21. #8 - 18 x 13/4" Screw - 2
22. Battery Clamp Cap
23. 12 V olt Charger
24. Wire Clip
Parts Not Shown:
Label Sheets - 3
Note: Some parts shown are assembled on both sides of the vehicle.
12-VOLT
CHARGER
1
Battery Charging
E
7
WARNING
• Battery can fall out and injure a child if vehicle tips over. Always use battery clamp.
PREVENT FIRE
- Never modify the electrical system.Alterations could cause a fire resulting in ser ious injury and could also ruin the electr ical system.
- Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury.
- Use of Power Wheels
®
components
in products other than Power Wheels
®
vehicles could cause overheating, fire or
explosion.
• The battery must be handled by adults only.The battery is heavy and contains sulfuric acid (electrolyte). Dropping the battery could result in ser ious injur y.
• Never allow children to charge the battery. Battery charging must be done by adults only. A child could be injured by the electricity involved in charging the batter y.
• Never lift or carry the battery by the wires or connector.This can damage the battery and possibly cause a fire resulting in serious injury. Lift and carr y the batter y by the case only.
• Read the safety instructions on the battery.
• Examine the battery, charger and their connectors for excessive wear or damage each time you charge the battery. If damage or excessive wear is detected, do not use the charger or the battery until you have replaced the worn or damaged part.
ELECTRICAL HAZARD
Battery Charging
8
IMPORTANT!
Your new battery must be charged for at least
18 hours before you use it in your vehicle for the first time. We recommend that you start charging your
battery before beginning assembly of your new vehicle.
• The battery must be upright while charging.
• The charger is not a toy.
• Do not short circuit the batter y.
• Before charging the battery, examine the battery case for cracks and other damage which may cause sulfuric acid (electrolyte) to leak during the charging process. If damage is detected, do not charge the battery or use it in your vehicle.Battery acid is very corrosive and can cause severe damage to surfaces it contacts.
• Do not charge the battery on a surface which could be damaged by the acid contained inside the battery. Take precautions to protect the surface on which you charge your battery.
• Use only a Power Wheels®12 volt charger with type “12V” connector (120 VAC 60 Hz 28W with an output of 12 VDC 1200mA) to charge your Power Wheels
®
rechargeable 12 volt battery.
• Once installed, you do not need to remove the battery from your vehicle to recharge it.
Pb
• Plug the charger connector into the battery .
• Plug the charger into a standard 120 volt wall outlet . Note: If power flow to the wall outlet is controlled by a
switch, make sure the switch is “ON”.
• Before first-time use, charge the battery for at least 18 hours. Never charge the battery longer than 30 hours.
• Recharge the battery for at least 14 hours after each use of your vehicle.Do not charge the battery longer than 30 hours.
• Once the battery is charged, pull firmly on the charger connector to disconnect it from the battery. Unplug the charger from the wall outlet.The battery is now ready to be installed in your vehicle.Please see the Battery Installation section on page 18 for detailed instructions on installing your battery. If your battery is already installed in your vehicle, simply re-connect the motor harness connector to the battery, lower and fasten the hood.
2
1
Battery
Charger Connector
1
2
CA UTION
Use the charger in dry locations only.
About Thermal Fuses
Your Power Wheels®12 volt battery is equipped with a built-in thermal fuse.The thermal fuse is a self-resetting safety device which automatically “trips” and shuts down operation of the vehicle if the vehicle is overloaded or the driving conditions too severe.Once a fuse has “tripped”, it will automatically reset itself after approximately 25 seconds and allow the vehicle to resume normal operations.To avoid repeated automatic shutdowns, do not overload the vehicle by exceeding the 130 lb. maximum weight capacity or by towing anything behind the vehicle.Avoid severe driving conditions, such as driving up steep slopes or running into fixed objects, which can cause the wheels to stop spinning while power is still being supplied to the motors. Make sure your child stops the vehicle before switching speeds or direction.
If a thermal fuse in a battery continually trips under normal driving conditions, please contact your local Pow er Wheels®Authorized Service Center.For the location of the Authorized Service Center nearest to you, see page 28.
Running Board
Tab (Bent Position)
Tab
Assembly
• Make sure that the three holes in the running board are aligned with the three holes in the vehicle body and that the flat side of the running board tab contacts the underside of the vehicle body (see inset).
• Insert three #8 x 3/4" screws through the holes in the vehicle body and into the running board.Tighten the screws using a Phillips screwdriver. Do not over-tighten.
3
• Bend the tab on a running board down (see inset).
• While holding the tab in place, fit the running board under the side edge of the vehicle body.
Hint: You may need to pull gently on the side of the vehicle body to fit the running board in place.
• Make sure the hole in the running board tab is aligned with the hole in the floor of the vehicle body. Inser t a #8 x 3/4" screw through the hole in the vehicle body floor and into the running board tab.Tighten the screw using a Phillips screwdriver. Do not over-tighten.
• Repeat assembly steps 1 - 3 to assemble the other running board to the other side of the vehicle body.
2
1
Vehicle Body
Running Board
Running Board
Running Board
Tab
Bottom View
F
Children can be harmed by small parts, sharp edges and shar p points in the vehicle’s unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle.
WARNING
9
Assembly
10
• Press firmly above one of the rear tabs to snap it into the slot in the vehicle body.
IMPORTANT! While snapping the rear tab into the slot, press on the side of the cab to prevent it from bowing. Make sure that the side tabs stay aligned with the slots.
6
Cab
PRESS DOWN HERE
To Snap Rear Tab
PRESS
HERE
To Keep in Place
• Position the three front tabs on the cab into the slots in the vehicle body. Do not snap the tabs into the slots.
• Position the side and rear tabs on both sides of the cab in the corresponding slots the vehicle body. Do not
snap the tabs into the slots.
5
Cab
Rear Tab
Side Tabs
Front Tabs
• Press down above the side of the cab while pulling up on the front fender to snap the side tabs into the slots.
• Repeat steps 6 and 7 to snap the rear and side tabs on the other side of the cab into the slots in the vehicle body.
7
PRESS
DOWN HERE
To Snap
Side T abs
PULL UP
4
• Insert two #8-18 x 13/4" screws through the holes in the front bumper and into the vehicle body.Tighten the screws using a Phillips screwdriver. Do not over-tighten.
Loading...
+ 22 hidden pages