PowerTec MT4005 Owner's Manual
Owner’s Manual
Model No. MT4005
MITER SAW STAND
You will need this manual for safety instructions, operating procedures, and warranty.
Put it and the original sales invoice in a safe, dry place for future reference.
Visit us on the web at www.southerntechllc.com
17-0515
QUESTION...
1•847•780•6120
PRODUCT
SPECIFICATIONS
Net Weight: ......................................49.5 lbs (22.5 kg)
Weight Capacity: .............................. 440 lbs (200 kg)
Table Size: .......................................32-9/32" x 18-1/32"
...........................................................820 mm x 458 mm
Table Height: .................................... 26-31/32" x 32-9/32"
...........................................................685 mm x 820 mm
Roller Extension Range: .................. 42-9/16" x 70-15/16"
...........................................................1081 mm x 1802 mm
Top of Feed Roller Height Range: ... 29-11/16" – 39-11/16"
...........................................................754 mm –1008 mm
TABLE OF CONTENTS
SAFETY RULES 1
ASSEMBLY 2
Unpacking
Tools Needed
Assembly
Mounting the Miter Saw
OPERATION 4
MAINTENANCE 5
General Maintenance
PARTS ILLUSTRATION 6
AND LIST
WARRANTY 7
SECTION PAGE
Roller/Extension Bars Adjustment
To Raise and Lower the Stand
Transportation
SAFETY RULES
1
1
SAFETY RULES
WARNING
For your own safety, read all of the rules and precautions
before operating tool.
WARNING
Always follow proper operating procedures as defined in
this manual even if you are familiar with use of this miter
saw stand or any tool used with this stand. Remember
that being careless for even a fraction of a second can
result in severe personal injury.
You must be familiar with the use of any tool or accessory
used with this miter saw stand. The supplier cannot
be held responsible for any accident, injury or damage
incurred while using this stand with any tool.
WARNING
Some dust created by operation of power tool contains
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm. To
reduce your exposure to these chemicals, work in a well
ventilated area and work with approved safety equipment.
Always wear OSHA/NIOSH approved, properly fitting face
mask or respirator when using such tools.
CAUTION
Do not modify or use this stand for any application other
than that for which it was designed.
SAFETY FOR WORK STAND
• Do not attempt to assemble or operate your miter saw
stand until you have read the safety instructions in this
section.
• Only use your miter saw stand on a hard, dry and flat
surface.
• Keep your work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not overreach. Keep proper footing and balance at
all times.
• Do not load the miter saw stand with more than 440 lbs
(200 kg).
• Store properly. Do not store the miter saw stand
outdoors or in a damp location.
• Do not stand or climb on miter saw stand. It could tip
over, causing serious injury.
• Do not permit children to use the miter saw stand
unsupervised. It is not a toy.
• Be sure work support extensions and legs are locked in
place before using your miter saw and miter saw stand.
• Test for stability of the miter saw stand before using
your miter saw and miter saw stand.
• Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair can be caught
in moving parts. Always wear non-slip footwear. Tie
back long hair. Roll long sleeves above the elbow.
• Always firmly attach the miter saw used with this stand.
Do not attempt to use the miter saw on the miter saw
stand until the miter saw is fastened firmly.
• Be sure all hardware mounting the miter saw to the
quick-release mounting brackets is tight before folding
and transporting the miter saw on the miter saw stand.
• Take care when folding the miter saw stand to reduce
the hazard of pinching hands and fingers.
• Be aware of tipping. When a large piece is cut from one
end of a job, the remaining piece may be heavy enough
to tip the miter saw stand. Always ensure the workpiece
is well supported.
• Always keep all guards in place. Be sure all power tool
guards are in good working order and are in proper
adjustment and alignment.
• Always keep your hands away from the cutting area.
CAUTION
Think safety! Safety is a combination of operator common
sense and alertness at all times when tool is being used.
WARNING
Do not attempt to operate tool until it is completely
assembled according to the instructions.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
2
ASSEMBLY
ASSEMBLY
2
UNPACKING
Refer to Figure 1
Check for shipping damage. Check immediately that all
parts and accessories are included.
ITEM DESCRIPTION QTY
A Main Frame 1
B Leg Extension 1
C Foot 1
D Wheels 2
E Roller Bars 2
F Handle 1
G Locking Knobs 4
H Locking Knobs (star) 2
I Hex Bolt (M12x75 mm) (wheel) 2
J Hex locking nut M12 (wheel) 2
K Phillip Pan Head Screw M6x35 (handle) 2
L Curved Washer (leg extension/foot) 4
M Phillip Pan Head Screw M6x12
(leg extension/foot)
4
N Feet End Caps 2
O Miter Saw Mounting Hardware
(mounting bolt, washer, lock washers and nut)
4
I
F
G
O
K
L M
Figure 1
A
H
D
B
C
E
J
N
WARNING
Do not use the miter saw stand until it is completely
assembled and you have read and understood this entire
operating manual and the operating manual of the tool
being used with this miter saw stand.
WARNING
Do not use the miter saw stand for scaffolding or as a
ladder. Make sure to securely tighten all fasteners before
using. Maximum capacity is 440 lbs (200 kg). Power tools
on the miter saw stand should not exceed a combined
overall height of 60" (152.4 cm) from the floor.
TOOLS NEEDED
The following tools (not included) are needed to assemble
the miter saw stand:
1 - Phillips screw driver (handle, leg extension and foot
assembly)
2 - Adjustable wrenches or two 19 mm wrenches
(wheel assembly)
ASSEMBLY
Refer to Figure 2–9
• Press the feet end caps onto the leg extension.
• Place the main frame onto the table top as shown. Slide
leg extension into main frame and secure with curved
washers and pan head screws.
• Lift the main frame and slide foot into main frame and
secure with curved washers and pan head screws.
Foot
Figure 2
Leg Extension
Table Top
Main Frame
Feet End
Caps
• Slide the hex bolt through the wheel and main frame leg.
Secure with hex locking nut on the inside of mainframe.
DO NOT over tighten, if too tight the wheels will not turn.
• Repeat with other wheel.
NOTE: Raised hub goes to the inside.
Figure 3
Wheel
Hex Bolt
Hex
Locking
Nut
Raised
Hub
Main Frame Leg
• Thread the locking knob (star shaped) onto the adjusting
bracket screw. Repeat on other side. DO NOT tighten
the locking knobs at this time.
Figure 4
Locking Knob (star)
Adjusting Bracket
Adjusting Bracket Screw
Loading...