PowerTec MT4004 Owner's Manual
Owner’s Manual
Model No. MT4004
MITER SAW STAND
You will need this manual for safety instructions, operating procedures, and warranty.
Put it and the original sales invoice in a safe, dry place for future reference.
Visit us on the web at www.southerntechllc.com
17-0216
QUESTION...
1•847•780•6120
PRODUCT
SPECIFICATIONS
Height .......................... 33-1/4" (845 mm)
Extended Width .................. 68-1/2" (1740 mm)
Maximum Load Capacity ..............330 lbs (150 kg)
Maximum Saw Mounting Width .......15-3/4" (400 mm)
Net Weight .....................33.55 lbs. (15.25 kg)
TABLE OF CONTENTS
SAFETY RULES 1
ASSEMBLY 2
Unpacking
Tools Needed
Unfold the Work Legs
Assemble Wheels
Assemble Handle
Assemble Roller Bar
Mounting the Miter Saw
OPERATIONS 4
Roller Bars/Extension Bars Adjustment
MAINTENANCE 5
General Maintenance
PARTS ILLUSTRATION 6
& LIST
WARRANTY 8
SECTION PAGE
SAFETY RULES
1
1
SAFETY RULES
WARNING
For your own safety, read all of the rules and precautions
before operating tool.
WARNING
Always follow proper operating procedures as defined
in this manual even if you are familiar with the use of
this miter saw stand or any tool used with this stand.
Remember that being careless for even a fraction of a
second can result in severe personal injury.
You must be familiar with the use of any tool or accessory
used with this miter saw stand. The supplier cannot
be held responsible for any accident, injury or damage
incurred while using this stand with any tool.
WARNING
Some dust created by operation of power tool contains
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm. To
reduce your exposure to these chemicals, work in a well
ventilated area and work with approved safety equipment.
Always wear OSHA/NIOSH approved, properly fitting face
mask or respirator when using such tools.
CAUTION
Do not modify or use this stand for any application other
than that for which it was designed.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
grounded power tools. Unmodified plugs and matching
outlets will reduce the risk of electric shock.
• Avoid body contact with grounded surfaces, such as
pipes, radiators, ranges, and refrigerators. There is an
increased risk of electric shock if your body is grounded.
• Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
• Do not abuse the cord. Never use the cord for carrying,
pulling, or unplugging the power tool. Keep the cord
away from heat, oil, sharp edges, or moving parts.
Damaged or entangled cords increase the risk of
electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter (GFCl}
protected supply. Use of a GFCI reduces the risk of
electric shock.
SAFETY FOR WORK STAND
• Do not attempt to assemble or operate your miter saw
stand until you have read the safety instructions in
this section.
• Only use your miter saw stand on a hard, dry and
flat surface.
• Keep your work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not overreach. Keep proper footing and balance at
all times.
• Do not load the miter saw stand with more than 330 Ibs
(150 kg).
• This stand is designed to be used with miter saws and
slide miter saws with a maximum mounting width of
15-3/4" (400 mm).
• Store properly. Do not store the miter saw stand
outdoors or in a damp location.
• Do not stand or climb on miter saw stand. It could tip
over, causing serious injury.
• Do not permit children to use the miter saw stand
unsupervised. It is not a toy.
• Be sure all locking pins are in the set-up position
holes before using your miter saw and miter saw miter
saw stand.
• Take care when moving the stand, especially when a
miter saw is mounted.
• Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair can be caught
in moving parts. Always wear non-slip footwear. Tie
back long hair. Roll long sleeves above the elbow.
• Always firmly attach the miter saw used with this stand.
Do not attempt to use the miter saw on the miter saw
stand until the miter saw is fastened firmly.
• Be aware of tipping. When a large piece is cut from one
end of a job, the remaining piece may be heavy enough
to tip the miter saw stand. Always ensure the workpiece
is well supported.
• Always keep all guards in place. Be sure all power tool
guards are in good working order and are in proper
adjustment and alignment.
• Always keep your hands away from the cutting area.
CAUTION
Think safety! Safety is a combination of operator common
sense and alertness at all times when tool is being used.
WARNING
Do not attempt to operate tool until it is completely
assembled according to the instructions.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
2
ASSEMBLY
ASSEMBLY
2
UNPACKING
Refer to Figure 1
Check for shipping damage. Check immediately whether
all parts and accessories are included.
ITEM DESCRIPTION QTY
A Miter Saw Stand 1
B Quick Release Mounting Brackets 2
C Roller Bars 2
D Axle 2
E Wheels 2
F Locking Nut M8 (wheels) 4
G Washer Ø8 (wheels) 4
H Washer Ø12 (wheels) 2
I Handle 1
J Screw M6 x 35 (handle) 2
K Nut M6 (handle) 2
L Miter Saw Mounting Hardware
(M8 x 45 mounting bolt, washer, lock
washers and nut)
4
A
B
F
C
H
G
I
KLJ
Figure 1
D
E
WARNING
Do not use the miter saw stand until it is completely
assembled and you have read and understood this entire
operating manual and the operating manual of the tool
being used with this miter saw stand.
WARNING
Do not use the miter saw stand for scaffolding or as a
ladder. Make sure to securely tighten all fasteners before
using. Maximum capacity is 330 lbs (150 kg). Power tools
on the miter saw stand should not exceed a combined
overall height of 60" (152.4 cm) from the floor.
TOOLS NEEDED
The following tools (not included) are needed to assemble
the miter saw stand:
Adjustable pliers
Phillips screwdriver
10 mm wrench or socket
13 mm wrench or socket
UNFOLD THE WORK LEGS
Refer to Figure 2
• Place the miter saw stand on a flat surface with the
folded legs facing up.
• Depress the release lever and rotate the leg until it
clicks and locks into the open position. Repeat for
each leg.
• The stand should be stable and should not rock.
Release
Lever
Figure 2
Release
Lever
• Place the miter saw stand in the upright position on a
flat surface.
ASSEMBLE WHEELS
Refer to Figure 3
• Slide the axle through the axle bracket, turn the axle
until the machined end fits into the inside bracket
hole. Place one small (Ø8) washer and nut onto axle.
Tighten nut.
NOTE: The axle has a retaining ring on one end and is
machined to fit the axle bracket hole on the other end,
make sure the machined end is inserted into the axle
bracket first.
• Slide one larger (Ø12) washer and the wheel on the
axle. Secure in place with the small (Ø8) washer and
nut. Tighten nut. NOTE: Raised hub goes to the inside.
• Repeat with other wheel.
Loading...