Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 1 of 14
www.power-one.com
Applications
• Distributed power architectures
• Telecommunications equipment
• LAN/WAN applications
• Data processing
• Industrial applications
Features
• Single board design
• 8.2 mm height profile
• Input/output isolation: 1500 Vdc
• Low conducted and radiated EMI
• Excellent co-planarity
• Output overcurrent protection
• Full rated output power at 100LFM airflow
• Operating temperature to 100°C
• Remote shutdown (primary referenced)
• Output voltage trim adjust, positive or
negative
• UL, CSA and EN/IEC60950 (3
rd
ed.)
approvals pending
Description
The NDS series of converters are low profile, single output, DC/DC converters intended for SMT placement
and reflow soldering. The product provides on-board conversion of standard telecom, datacom and
industrial input voltages to isolated low output voltages. Proprietary patented manufacturing process
ensures optimal quality with full process automation. These are high performance, cost effective converters
with an extremely small PCB footprint.
Selection Chart
Model Input voltage
range,
Vdc
Input
current,
max Adc
Output
voltage,
Vdc
Output rated
current,
Adc
Output ripple
and noise,
mVp-p
Efficiency,
%
NDS03ZA-M6
36-75 0.18 1.5 3.0 40 77
NDS03ZB-M6
36-75 0.22 1.8 3.0 45 79
NDS03ZD-M6
36-75 0.28 2.5 3.0 60 83
NDS03ZE-M6
36-75 0.35 3.3 3.0 75 85
NDS02ZG-M6
36-75 0.35 5.0 2.0 90 87
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 2 of 14
www.power-one.com
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings may cause performance degradation, adversely affect
long-term reliability and cause permanent damage to the converter. Specifications apply over specified input
voltage, output load and temperature range, unless otherwise noted.
Parameter Conditions/Description Min Max Units
Input voltage (Vin)
Transient Input Voltage (Vint)
Continuous
Transient, 100ms
36 75
100
Vdc
Vdc
Operating CaseTemp. (Tc) At 100% load -40 100
°C
Storage Temperature (Ts) -55 120
°C
ON/OFF Control Voltage (Vrc) Referenced to -Vin -1.0 5.5 Vdc
Environmental and Mechanical Specifications
Specifications apply over specified input voltage, output load and temperature range, unless otherwise
noted.
Parameter Conditions/Description Min Nom Max Units
Shock IEC68-2-27 100 g
Sinusoidal Vibration IEC68-2-6 10 g
Weight 0.4/10 oz/g
Water W ashing Standard process Yes N/A
MTBF Per Bellcore TR-NWT-000332 2,500 kHrs
Isolation Specifications
Specifications apply over specified input voltage, output load and temperature range, unless otherwise
noted.
Parameter Conditions/Description Min Nom Max Units
Insulation Safety Rating Vin = 36 – 75Vdc Basic N/A
Isolation Voltage (Vps) 1,500 Vdc
Isolation Resistance (Rps) 10 MOhm
Isolation Capacitance (Cps) 4,100 pF
Input Specifications
Specifications apply over specified input voltage, output load and temperature range, unless otherwise
noted.
Parameter Conditions/Description Min Nom Max Units
Input Voltage (Vin) Continuous 36 48 75 Vdc
Input Current when Shutdown Vin.Nom, Remote Control
activated
3 6 mAdc
Turn-On Input Voltage 36-75 Vin Ramping Up, Io.Max 32 34 36 Vdc
Turn-Off Input Voltage 36-75 Vin Ramping Down, Io.Max 30 32 34 Vdc
Turn-On Time To Output Regulation Band
After Remote Control
Rise Time
350
1
1
500
5
5
ms
ms
ms
Input Reflected Ripple Current Vin.Max, Io.Max 50 mAp-p
Input Capacitance 1.4
µF
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 3 of 14
www.power-one.com
Output Specifications
All specifications apply over input voltage, output load and temperature range, unless otherwise noted.
NDS03ZA : 1.5V/3.0A
Parameter Conditions/Description Min Nom Max Units
Output Voltage
Setpoint Accuracy
Vo
Vin.Nom, Io = 1.5A, 25°C
1.48 1.50 1.52 Vdc
Output Current Io Vin.Min to Vin.Max 0 3.0 Adc
Line Regulation Vin.Min to Vin.Max, 50%
Io.Max
25 mV
Load Regulation Vin.Nom, Io.Min to Io.Max 25 mV
Dynamic Regulation
Peak Deviation
Settling Time
50-100% Io.Max load step
change.
to 1% error band
250
1,150
± mV
µs
Output Voltage Ripple* Vr Vin.Min to Vin.Max, Io.Min to
Io Max, 20MHz Bandwidth
40 75 mVp-p
Admissible Load
Capacitance
Comax Io.Max, Vin.Nom 2,200
µF
Output Current Limit
Threshold
Icl Vout ≤0.90 Vo.Nom 120 200 %Io.Max
Switching Frequency Fs Vin.Nom, Io.Max 400 kHz
Temperature
Coefficient
Tco 0.02
%Vo/°C
Trim Range Vt Io.Min to Io.Max, Vin.Min to
Vin.Max
1.35 1.65 Vo
* Measured with a 1µF ceramic across the output pins
NDS03ZA Characteristic curves
Output Voltage Vs Load
0.00
0.20
0.40
0.60
0.80
1.00
1.20
1.40
1.60
0.00
0.45
0.90
1.35
1.80
2.25
2.70
3.15
3.60
4.05
4.50
4.95
5.40
5.85
Iout (A)
Vout (V)
Vin Min
Vin Nom
Vin Max
Efficiency Vs Load
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
0.00
0.15
0.30
0.60
0.90
1.20
1.50
1.80
2.10
2.40
2.70
3.00
Iout (A)
Efficiency
Vin Min
Vin Nom
Vin Max
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 4 of 14
www.power-one.com
Output Specifications
All specifications apply over input voltage, output load and temperature range, unless otherwise noted.
NDS03ZB : 1.8V/3.0A
Parameter Conditions/Description Min Nom Max Units
Output Voltage
Setpoint Accuracy
Vo
Vin.Nom, Io = 1.5A, 25°C
1.78 1.80 1.82 Vdc
Output Current Io Vin.Min to Vin.Max 0 3.0 Adc
Line Regulation Vin.Min to Vin.Max, 50%
Io.Max
25 mV
Load Regulation Vin.Nom, Io.Min to Io.Max 25 mV
Dynamic Regulation
Peak Deviation
Settling Time
50-100% Io.Max load step
change.
to 1% error band
250
1,150
± mV
µs
Output Voltage Ripple* Vr Vin.Min to Vin.Max, Io.Min to
Io Max, 20MHz Bandwidth
50 75 mVp-p
Admissible Load
Capacitance
Comax Io.Max, Vin.Nom 2,200
µF
Output Current Limit
Threshold
Icl Vout ≤0.90 Vo.Nom 120 200 %Io.Max
Switching Frequency Fs Vin.Nom, Io.Max 400 kHz
Temperature
Coefficient
Tco 0.02
%Vo/°C
Trim Range Vt Io.Min to Io.Max, Vin.Min to
Vin.Max
1.62 1.98 Vo
* Measured with a 1µF ceramic across the output pins
NDS03ZB
Characteristic curves
Output Voltage Vs Load
0.00
0.20
0.40
0.60
0.80
1.00
1.20
1.40
1.60
1.80
2.00
0.00
0.60
1.20
1.80
2.40
3.00
3.60
4.20
4.80
5.40
6.00
Iout (A)
Vout (V)
Vin Min
Vin Nom
Vin Max
Efficiency Vs Load
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
0.00
0.15
0.30
0.60
0.90
1.20
1.50
1.80
2.10
2.40
2.70
3.00
Iout (A)
Efficiency
Vin Min
Vin Nom
Vin Max
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 5 of 14
www.power-one.com
Output Specifications
All specifications apply over input voltage, output load and temperature range, unless otherwise noted.
NDS03ZD : 2.5V/3.0A
Parameter Conditions/Description Min Nom Max Units
Output Voltage
Setpoint Accuracy
Vo
Vin.Nom, Io = 1.5A, 25°C
2.47
2.5 2.53 Vdc
Output Current Io Vin.Min to Vin.Max 0 3.0 Adc
Line Regulation Vin.Min to Vin.Max, 50%
Io.Max
50 mV
Load Regulation Vin.Nom, Io.Min to Io.Max 50 mV
Dynamic Regulation
Peak Deviation
Settling Time
50-100% Io.Max load step
change.
to 1% error band
250
1,150
± mV
µs
Output Voltage Ripple Vr Vin.Min to Vin.Max, Io.Min to
Io Max, 20MHz Bandwidth
50 75 mVp-p
Admissible Load
Capacitance
Comax Io.Max, Vin.Nom 2,200
µF
Output Current Limit
Threshold
Icl Vout ≤0.90 Vo.Nom 120 200 %Io.Max
Switching Frequency Fs Vin.Nom, Io.Max 400 kHz
Temperature
Coefficient
Tco 0.02
%Vo/°C
Trim Range Vt Io.Min to Io.Max, Vin.Min to
Vin.Max
2.25 2.75 Vo
* Measured with a 1µF ceramic across the output pins
NDS03ZD
Characteristic curves
Output Voltage Vs Load
0.00
0.50
1.00
1.50
2.00
2.50
3.00
0.00
0.60
1.20
1.80
2.40
3.00
3.60
4.20
4.80
5.40
6.00
Iout (A)
Vout (V)
Vin Min
Vin Nom
Vin Max
Efficiency Vs Load
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
0.00
0.15
0.30
0.60
0.90
1.20
1.50
1.80
2.10
2.40
2.70
3.00
Iout (A)
Efficiency
Vin Min
Vin Nom
Vin Max
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 6 of 14
www.power-one.com
Output Specifications
All specifications apply over input voltage, output load and temperature range, unless otherwise noted.
NDS03ZE : 3.3V/3.0A
Parameter Conditions/Description Min Nom Max Units
Output Voltage
Setpoint Accuracy
Vo
Vin.Nom, Io = 1.5A, 25°C
3.26
3.3 3.34 Vdc
Output Current Io Vin.Min to Vin.Max 0 3.0 Adc
Line Regulation Vin.Min to Vin.Max, 50%
Io.Max
65 mV
Load Regulation Vin.Nom, Io.Min to Io.Max 65 mV
Dynamic Regulation
Peak Deviation
Settling Time
50-100% Io.Max load step
change.
to 1% error band
250
250
± mV
µs
Output Voltage Ripple* Vr Vin.Min to Vin.Max, Io.Min to
Io Max, 20MHz Bandwidth
50 75 mVp-p
Admissible Load
Capacitance
Comax Io.Max, Vin.Nom 2,200
µF
Output Current Limit
Threshold
Icl Vout ≤0.90 Vo.Nom 120 200 %Io.Max
Switching Frequency Fs Vin.Nom, Io.Max 400 kHz
Temperature
Coefficient
Tco 0.02
%Vo/°C
Trim Range Vt Io.Min to Io.Max, Vin.Min to
Vin.Max
3.0 3.6 Vo
* Measured with a 1µF ceramic across the output pins
NDS03ZE
Characteristic curves
Output Voltage Vs Load
0.00
0.50
1.00
1.50
2.00
2.50
3.00
3.50
0.00
0.45
0.90
1.35
1.80
2.25
2.70
3.15
3.60
4.05
4.50
4.95
5.40
5.85
Iout (A)
Vout (V)
Vin Min
Vin Nom
Vin Max
Efficiency Vs Load
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
0.00
0.30
0.90
1.50
2.10
2.70
Iout (A)
Efficiency
Vin Min
Vin Nom
Vin Max
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 7 of 14
www.power-one.com
Output Specifications
All specifications apply over input voltage, output load and temperature range, unless otherwise noted.
NDS02ZG : 5.0V/2.0A
Parameter Conditions/Description Min Nom Max Units
Output Voltage
Setpoint Accuracy
Vo
Vin.Nom, Io = 1.0A, 25°C
4.94
5.0 5.06 Vdc
Output Current Io Vin.Min to Vin.Max 0 2.0 Adc
Line Regulation Vin.Min to Vin.Max, 50%
Io.Max
65 mV
Load Regulation Vin.Nom, Io.Min to Io.Max 65 mV
Dynamic Regulation
Peak Deviation
Settling Time
50-100% Io.Max load step
change.
to 1% error band
350
250
± mV
µs
Output Voltage Ripple* Vr Vin.Min to Vin.Max, Io.Min to
Io Max, 20MHz Bandwidth
75 125 mVp-p
Admissible Load
Capacitance
Comax Io.Max, Vin.Nom 2,200
µF
Output Current Limit
Threshold
Icl Vout ≤0.90 Vo.Nom 120 200 %Io.Max
Switching Frequency Fs Vin.Nom, Io.Max 400 kHz
Temperature
Coefficient
Tco 0.02
%Vo/°C
Trim Range Vt Io.Min to Io.Max, Vin.Min to
Vin.Max
4.5 5.5 Vo
* Measured with a 1µF ceramic across the output pins
NDS02ZG
Characteristic curves
Output Voltage Vs Load
0.00
1.00
2.00
3.00
4.00
5.00
6.00
0.00
0.30
0.60
0.90
1.20
1.50
1.80
2.10
2.40
2.70
3.00
3.30
3.60
3.90
Iout (A)
Vout (V)
Vin Min
Vin Nom
Vin Max
Efficiency Vs Load
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
0.00
0.20
0.60
1.00
1.40
1.80
Iout (A)
Efficiency
Vin Min
Vin Nom
Vin Max
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 8 of 14
www.power-one.com
Feature Specifications
All specifications apply over input voltage, output load and temperature range, unless otherwise noted.
Parameter Conditions/Description Min Nom Max Units
Shutdown Control:
Converter OFF
Converter ON
Sink Current
Shutdown pin is pulled low
Voltage source or open circuit
Vin=Vin.Nom
-1.0
3.5
0.3
1.0
5.5
Vdc
Vdc
mAdc
Temperature Derating Curves
The derating curves below give an indication of the output power achievable with and without forced aircooling. However in the final application, in order to ensure the reliability of the unit, care must be taken to
ensure the maximum case temperature is not exceeded under any conditions.
Output Power Vs AmbientTemp. and Airflow
0
20
40
60
80
100
120
0
10
20
30
40
50
60
70
80
90
100
Ambient Temperature (deg °C)
Output Power (%)
200LFM (1 m/s)
100LFM (0.5 m/s)
0 LFM
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 9 of 14
www.power-one.com
Typical Application
This series of converters does not require any
external components for proper operation.
However, if the distribution of the input voltage to
the converter contains significant inductance, a
capacitor across the input terminals may be
required to stabilize the input voltage. A minimum
of 1µF, quality electrolytic / ceramic capacitor is
recommended for this purpose.
For output decoupling it is recommend connecting
a 1µF ceramic capacitor directly across the output
pins of the converter.
Shutdown Feature
The remote control pin functions as a normal soft
shutdown. It is referenced to the –Vin pin. With
positive logic, when the remote control pin is pulled
low, the output is turned off and the unit goes into a
very low input power mode.
An open collector switch is recommended to control
the voltage between the remote control pin and the
-Vin pin of the converter. The remote control pin is
pulled up internally, so no external voltage source
is required. The user should avoid connecting a
resistor between the remote control pin and the
+Vin pin.
The user must take care to ensure that the pin
reference for the control is connected close to the Vin pin. The control signal must not be referenced
ahead of EMI filtering, or remotely from the unit. If
the remote control pin is not used, it can be left
floating.
Thermal Considerations
The converter is designed for natural or forced
convection cooling. The output power of the
converter is limited by the maximum case
temperature (Tc). To ensure reliable long term
operation of the converters, and to comply with
safety agency requirements, Power-One limits
maximum allowable case temperature (Tc) to
100°C (see Mechanical Drawings).
Parallel Operation
Paralleling of two converters is not possible.
Output Current Limiting
When the output is overloaded above the maximum
output current rating, the voltage will start to reduce
to maintain the output power to a safe level. In a
condition of high overload or short-circuit where the
output voltage is pulled below approximately 30%
of Vo.Nom, the unit will enter a ‘Hiccup’ mode of
operation. Under this condition the unit will attempt
to restart, approximately every 25ms until the
overload has cleared.
Output Voltage Trim
The trim feature allows the user to adjust the output
voltage from the nominal.
Output voltage can be adjusted by an external
resistor. To increase Vo a resistor should be
connected between pins 12 and 14. To decrease
Vo a resistor should be connected between pins 12
and 13.
To increase Vo:
Rext = (A – (D x Vout)) / ( Vout – Vout.Nom)
To reduce Vo:
Rext = ((B x Vout) - C) / ( Vout.Nom - Vout)
Where Vout is the desired output voltage
Model A B C D
NDS03ZA
1945 1470 1944 470
NDS03ZB
2590 1730 2560 750
NDS03ZD
5010 2516 5010 1500
NDS03ZE
7010 3161 7010 1500
NDS02ZG
11260 4532 11240 1500
Note:
When the output voltage is trimmed up, the output
power from the converter must not exceed its
maximum rating. This is determined by measuring
the voltage on the output pins, and multiplying it by
the output current.
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 10 of 14
www.power-one.com
Safety Considerations
These converters feature 1500 Volt DC isolation
from input to output. The input to output resistance
is greater than 10MOhm. These converters are
provided with Operational Insulation between input
and output circuits according to EN60950 / UL1950
/ CSA60950-00. Nevertheless, if the system using
the converter needs to receive safety agency
approval, certain rules must be followed in the
design of the system. In particular, all of the
creepage and clearance requirements of the enduse safety requirements must be observed. These
documents include UL60950, CSA60950-00 and
EN60950, although specific applications may have
additional requirements.
In order for the output of the converter to be
considered as SELV (Safety Extra Low Voltage) or
TNV-1, according to EN60950 / UL1950 /
CSA60950-00, one of the following requirements
must be met in the system design:
• The converter has no internal fuse. An external
fuse must be provided to protect the system
from catastrophic failure. A fuse with a rating
not greater than 2.0A is recommended. The
user can select a lower rating fuse based upon
the inrush transient and the maximum input
current of the converter, which occurs at the
minimum input voltage. Both input traces and
the chassis ground trace (if applicable) must be
capable of conducting a current of 1.5 times the
value of the fuse without opening. The fuse
must not be placed in the grounded input line, if
any.
• If the voltage source feeding the module is
SELV, the output of the converter is considered
SELV and may be grounded or ungrounded.
• The circuitry of the converter may generate
transients, which exceed the input voltage.
Even if the input voltage is SELV (<60V) the
components on the primary side of the converter
may have to be considered as hazardous. A
safety interlock may be needed to prevent the
user from accessing the converter while
operational.
EMC Specifications
Conducted Noise:
The converters meet the requirements of
EN55022, CISPR22 and FCC CFR title 47 part 15
Sub-part J - Conducted (conducted noise on the
input terminals) without any external components.
The results for this solution are displayed below.
To meet level B for the above standards it is
necessary to fit a 5µF ceramic capacitor across the
input terminals.
Electromagnetic Susceptibility:
Standard Applied
Stress
Class
Level
Performance
Outcome *
Electrostatic
Discharge
EN61000-4-2
2KV to
pins
1 B
Electromagnetic
Field
EN61000-4-3
3V/m 2 A
Electrical Fast
Transient
EN61000-4-4
2000 Vp
to input
3 B
Conducted
Disturbances
EN61000-4-6
3Vrms to
input
2 B
* A denotes normal operation, no deviation from
specification. B denotes temporary deviation from
specification is possible.
Conducted EMI (Input Terminals)
0
10
20
30
40
50
60
70
80
1.E+05 1.E+06 1.E+07 1.E+08
FREQ (MHz)
dbµV
EN55022 A AV.
EN55022 A QP.
0.1 1 10 30
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 11 of 14
www.power-one.com
Surface Mount Assembly
Soldering:
The following instructions must be observed when
soldering the unit. Failure to observe these
instructions may result in failure or significant
degradation of the module performance. PowerOne will not honor any warranty claims arising from
failure to observe these instructions.
This product is approved for forced convection
reflow soldering only.
The curves below define the maximum peak reflow
temperature permissible measured on Pins 1 and
10 of the converter.
The lead-frame is constructed for a high
temperature glass filled, UL94V0 flame retardant,
diallyl ortho-phthalate moulding compound
commonly used for packaging of electronics
components. It has passed NASA outgassing
tests and is certified to MIL-M-14. The coefficient
of thermal expansion is equivalent to FR4.
The gull wing leads are formed to ensure optimal
solder joint strength and structure. Furthermore
they facilitate visual inspection (manual or
automatic). The leads are formed from a 97% Cu
alloy plated with Cu and Sn 90. This material is
commonly used in the manufacture of integrated
circuits. It has good corrosion resistance and
exhibits the nobility inherent to all high copper
alloys. Unlike brasses, this material is essentially
immune to stress corrosion cracking. It also
exhibits excellent solderability. It is readily wetted
by solders and performs well in standard
solderability tests. (Dip of Class II or better).
The product is manufactured with a patented
process, which is fully automated, and ‘in-line’.
This ensures that there is no contamination or
mechanical stress on the lead-frame so that the co
planarity and solderability are maintained.
The product is shipped in JEDEC trays to
guarantee preservation of the co-planarity and
enable fully automated assembly in the final
application.
.
Pick & Place Assembly:
The product is designed with a large flat area in the
center of the top surface to serve as a pick up point
for automated vacuum pick and place equipment.
The ‘open board’ construction of the unit ensures
that weight is kept to a minimum. However due to
the relatively large size of the component, a large
nozzle (> 3.0mm, depending on vacuum pressure)
is recommended for picking and placing.
The unit may also be automatically handled using
‘odd-form’ placement equipment, with mechanical
grippers. For this type of equipment the end edges
of the device, which have no leads and also feature
the greatest dimensional accuracy, should be used
as pick-up points.
Restriction curve above 215ºC
Peak temp. at pins 1 and 10 (ºC)
200
205
210
215
220
225
230
235
240
245
10 20 30 40 50 60
tp (s)
Time (s)
0
50
100
150
200
250
300
0
40
80
120
160
200
240
280
320
360
400
440
Max. temp. on pins 1 and 10 during reflow
soldering (deg C)
tp
Peak Temperature
(See fig below)
190 – 450 s
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 12 of 14
www.power-one.com
Note:- mm[inches]
Tolerances: -
0.5-10 ±0.1
10-100 ±0.2
Mechanical Drawings
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 13 of 14
www.power-one.com
RECOMMENDED LAND PATTERN
Product Specifications
NDS Series: 10W / 3.0A DC/DC Converters Nov 2001
36-75V Input
1.5V, 1.8V, 2.5V, 3.3V and 5.0V Outputs
5-Nov-01 Rev 1.1 Page 14 of 14
www.power-one.com
Pin-Out
Pin Designation Function Reference
1 Shutdown Shutdown control. Pull low to turn unit off Primary
2 -Vin Input voltage return Primary
3 NC No connection Primary
4 No Pin No pin
5 No Pin No pin
6 No Pin No pin
7 No Pin No pin
8 No Pin No Pin
9 NC No connection Secondary
10 NC No connection Secondary
11 NC No connection Secondary
12 Trim Output voltage adjust Secondary
13 +Vout Positive output voltage Secondary
14 -Vout Output voltage return Secondary
15 NC No connection Secondary
16 NC No connection Secondary
17 No Pin No pin
18 No Pin No pin
19 No Pin No pin
20 No Pin No pin
21 No Pin No Pin
22 NC No connection Primary
23 +Vin Positive input voltage Primary
24 NC No connection Primary
Ordering Information
Options Suffixes to add to part number
Surface Mount Version, shipped
in JEDEC Tray
Add Suffix “–M6”.
Through hole (leaded) version. Consult factory for availability.
24V input version Consult factory for availability.
Notes
1. Consult factory for the complete list of available options.
2. Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous
environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.
3. Specifications are subject to change without notice.
Loading...