PowerMax PM91001 User Manual
Multi-Function Automobile
Emergency JUMP START
Versatile
Mobile power Emergency Compact
Multi-Function Automobile
Emergency JUMP START
supply lighting
Product Instruction
For PM91001
Series 12V
Carstart
1
1.
WARNING
Please read this instruction carefully before you
make any operation on your vehicle. This device
contains battery product that may cause personal
injuries. If you are uncertain or have questions
about this device, please call 1-888-832-3557 THIS
IS FOR 12V SYSTEM ONLY, DAMAGES CAUSE
BY IMPROPER USE WILL SOLELY BE USER’S
RESPONSIBILITIES.
Do not crank start your vehicle for more than 5
second, or longer. This will damage your vehicle
starting system and over heat the JUMP START
battery. As a precaution, please allow JUMP
START to rest for 30 second, before starting
your vehicle.
•Do not use the device in the rain or wet conditions. Unit is not
waterproofs. The functionality of device might be affected.
•Keep the device away from where the children can access.
Never attempt to alter or disassemble the product. If there is
a problem with the product please contact your dealer for
further assistance.
•Do not allow metal to come in contact with the battery poles.
It may spark or short-circuit the battery and cause an
explosion.
•Stop using the jumpstart when you hear the alarm or cannot
turn on the JUMPSTART. The reason may be from:
①
The jumpstart device voltage is less than 9V - Charge the
jumpstart to prevent battery failure.
②The device temperature is higher than 140˚F (55˚C) - Cool
the jumpstart to at least 104˚F (40˚C) or below.
③
The jumpstart is connected backwards, incorrectly
connected or short connected. Correct it before start
•If Vehicle battery is less than 2V, there is no safety check to
prevent incorrect polarity hook up.
MUST READ:
Before using the JUMPSTART, read and follow the
instructions carefully. Also pay close attention to
the cautionary statements on the vehicle battery
and any other equipment.
MUST NOT DO:
NOTE:
As a safety measure, there is NO VOLTAGE present
at the clamp ends. The product automatically detects
when it is hooked up correctly to a battery, LCD
displays the voltage of vehicles battery if the
voltage is within 4V~14.2V. Only when JUMP START
button is pressed, the power will be delivered to the
clamps.
2 3
HYD-SERIES
8
5
6 7
10
Charge Input (12V/1A)
6
Light Mode Selector
2.
PRODUCT FUNCTIONS AND FEATURES
3.SPECIFICATIONS
Battery Type
Li-Polymer
Charging
110-220VAC Charger OR 12VDC IN CAR Charger
Outputs
Peak Amps:
700A
12VDC 6A Output (with 8A overload protection)
19VDC 3.5A Output (with 4A overload protection)
USB - 5VDC, 2.1A
High Intensity LED 1W
Weight
0.8Kg (1.76LB)
Product Size
7.08〃x3.54〃x1.49〃( 180mm x 90mm x 38mm )
12V/6A Out For OBD II
19V/3.5A Output
Jump Start Button
8
LCD Display
Features
• Jump starts your car dead battery under emergency situation.
Up to 8 cylinder 5 L vehicles
•Reverse polarity alarm warning, Built-in short circuit protection,
low voltage protection and over-temperature protection.
•A 12V/6A DC power outlet with overload protection provides
power for car memory saver (OBD II) and other 12V devices. (If
equipped)
•A 19V/3.5A DC power outlet with overload protection provides
power for most laptop computers with correct Barrel connector.
(If equipped)
•Charge with a 12V/1A AC charger and optional 12V/1A DC
•A USB 5V/2.1A provides power for small electrical appliances
(iPhone , iPad, ANDROID, PDA etc.)
•High intensity LED light can be used for emergency lighting and
emergency flashing.
•LCD display shows the both Jump start power level and car leadacid battery status with voltage test functions.
•Spark proof design: Once the car engine has successfully been
ignited, this JUMP START product will cut off the output power
USB Output (5V/2.1A) 9
Power Button ON/OFF
LED Work Light
Booster Cable Connector
within 2s
•Auto off mode: after turn on, if the unit is not in use, the main
power of the device will automatically shut off after 1 minute.
10
Loading...