PowerMadd 14250 User Manual
Handguard Mounting Kit - Snow
Installation Instructions for Part No. 14250 (Snowmobiles)
HARDWARE INCLUDED: TOOLS REQUIRED:
Qty
1 Straight Aluminum Bracket - throttle side • 10mm Wrench (2)
1 Curved Aluminum Bracket -brake side
2 M6 x 25mm Screws
2 M6 Lock Nuts
2 Square Nuts
2 M5 x 10mm Screws
2 Anti-spin Spacers
2 Long Spacers
Description • 3mm Hex Wrench
1 Steel Strap long – throttle side
1 Steel Strap short – brake side
2 M6 x 65mm Screws
2 M6 x 45mm Screws
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLATION!
NOTE: PowerMadd’s brackets are designed to mount to the
bare handlebar in between the grip and the controls. Some
snowmobiles may require moving the throttle block and/or
brake master cylinder over and away from the grip to create a
space for the bracket to mount. You may even need to cut off
some of the grip, but be careful not to cut any hand warmer
wires.
THROTTLE SIDE BRACKET
STEP 1: Slide the steel strap onto the handlebars in between
the throttle block and the end of the grip. Any wires should go
outside the strap.
STEP 2: Attach the aluminum bracket to the strap by inserting
the short M5 screw and tighten it with a 3mm hex wrench.
STEP 3: Insert the M6 x 25mm screw through the bracket and
the strap. Thread it into the square nut and tighten. This
adjustment screw is used to achieve the desired tightness of the
mount. Leave the bracket loose enough for now so you can
adjust the position up or down after attaching the hand guard to
the bracket.
BRAKE SIDE BRACKET
STEP 4: Slide the steel strap onto the handlebars in between
where the brake master cylinder mounts to the handlebars and
the end of the grip. Any wires should go outside the strap.
STEP 5: Attach this bracket to the strap the same as in STEPS
2 & 3.
© 2010 PowerMadd
1-800-435-6881 www.powermadd.com
IN14250
HAND GUARD MOUNTING
STEP 6: The 4 pictures below show the options for mounting the hand guard to the bracket.
These options allow you to move the guard right or left depending on the position you prefer.
Hold the hand guards up to the mounted brackets to decide which mounting option to use. Then
follow the instructions below for the option you have chosen.
When mounting the handguard to the bracket, make sure the no-spin spacer is positioned so that
the pin goes into the back hole of the bracket and the bolt goes through the front hole. Also
make sure the no-spin spacer is positioned so that its tabs go over one of the handguard tabs as
in the Option photos below.
Option 1 Option 2 Option 3 Option 4
Option 1 & 2 - RECOMMENDED: The strongest mounting option is to have the bracket and
no-spin spacer inside the handguard tabs. Thread the M6 x 45mm hex head bolt through the
handguard tab, the no-spin spacer and bracket, and then the other tab. Thread the lock nut onto
the bolt and tighten using 10mm wrenches.
Option 3 & 4: Position the no-spin spacer on the bracket and handguard tab. Thread the M6 x
65mm hex head bolt through the bracket, no-spin spacer and handguard tab. Insert the long
spacer in between the handguard tabs and continue to thread the bolt through the long spacer
and the other handguard tab. Thread the lock nut onto the bolt and tighten using 10mm
wrenches.
STEP 7: Adjust both handguards to the desired up/down position by spinning the bracket on
the handlebar. Once in position, use a 10mm wrench to tighten the M6 x 25mm hex head bolt
both brackets. DO NOT over tighten the mounts, you want them tight enough that they won’t
move if you land hard or hit a big bump, but you don’t want them too tight that they won’t
rotate if you were to crash.
STEP 8: All fasteners may need to be retightened after the first ride. Check the tightness
of the bracket and guard before each ride.
LIMITED WARRANTY
POWERMADD warrants this product to be free from defects in material and workmanship under use for the
purpose it was intended. POWERMADD shall not be liable for damage or injury caused by defective materials
or workmanship. POWERMADD may elect to repair or replace this product, but is the sole judge of any
defects in their product. This warranty does not cover any labor costs to remove or reinstall this product and is
effect for one year from the original purchase date.
© 2010 PowerMadd
IN14250
1-800-435-6881 www.powermadd.com
Loading...