Page 1
T-7001-TW
TWO WAY CAR ALARM
T-7001-TW-LCD
TWO WAY CAR ALARM WITH LCD DISPLAY
OWNER’S MANUAL
Page 2
TRANSMITTER OPERATIONS
ONE WAY VALET TRANSMITTER FOR
T-7001-TW & T-7001-TW-LCD
TWO WAY TRANSMITTER FOR
T-7001-TW
TWO WAY LCD TRANSMITTER FOR
T-7001-TW-LCD
COMMON BUTTON USED BY 3 TYPES OF TRANSMITTERS
:
ARM & LOCK THE DOORS
:
DISARM & UNLOCK THE DOORS
:
TO OPEN SLIDING DOOR ( IF EQUIPPED) OR REMOTE ENGINE STARTING)
2 sec:
TRUNK RELEASE
, :
TEMPORARY VALET MODE WHEN SYSTEM IS DISARMED
2 sec:
PANIC MODE
Page 3
TRANSMITTER OPERATIONS
TRANSMITTER WITH L.E.D
AUX:
TO OPEN SLIDING DOOR ( IF EQUIPPED) OR REMOTE ENGINE STARTING
, (AT THE SAME TIME):
SELECT 1ST OR 2ND VEHICLE
, AUX (AT THE SAME TIME):
BATTERY SAVER: SELECT PAGING TRANSMITTER ON/OFF
TRANSMITTER WITH SCREEN LCD DISPLAY
, (AT THE SAME TIME):
SELECT 1ST OR 2ND VEHICLE
F AND S
BATTERY SAVER . To Select Paging Transmitter ON/OFF
• Every time you press a button, transmitter emits 1 short beep. If you keep pressing the same button you will hear a second
beep. Depending on the number of beeps (1 short or 2 short beeps) you will have access to the different functions of the
system.
• When alarm is triggered the system will page the transmitter. To stop the alarm it requires pressing any button on the
remote.
Page 4
TWO WAY LCD TRANSMITTER OPERATIONS
Page 5
T-7001-TW-LCD @TWO WAY LCD TRANSMITTER OPERATIONS
Adjust real time clock
Keep pressing "F" button until appear then release. The display will show the hour numbers flashing. Use " "
button to select the hour, minutes or Am/Pm. Then use the " " button to increase or the " " button to decrease time.
When it is done, press "F" button to exit.
NOTE: You can exit programming mode anytime by pressing the "F" button.
Adjust wake-up timer
Keep pressing "F" button until appear then release. The display will show the hour numbers flashing. Use " "
button to select the hour, minutes or Am/Pm. Then use the " " button to increase or the " " button to decrease time.
When the wake-up timer is set, you can enable or disable wake-up by accessing the "S" functions. When it is done, press "F"
button to exit.
Enable wake-up timer
Keep pressing "S" button until appear then release. Then use the " " button or the " " button to enable/disable
this option. The "wake-up timer" icon will turn ON if it is enable.
Page 6
T-7001-TW-LCD @TWO WAY LCD TRANSMITTER OPERATIONS
Change SOUND to VIBRATION on your transmitter
Keep pressing "S" button until appear then release. Then use the " " button or the " " button to toggle between
SOUND or VIBRATION option. The corresponding "Audible" or "Vibration" icon will be display.
Replace the battery of your transmitter
If you want to replace the battery without readjust the time and all your settings, use the following instructions. Keep pressing "S"
button until appear then release. Then press the " " button or the " " button, you will see displayed.
Now, you can replace the battery. Otherwise, press "S" button to exit this mode.
Battery Saver (Enable/Disable paging to transmitter)
For 2 way transmitter, normal AAA battery is last for 1.to 2 months in normal use . To save battery for transmitter, you can
enable or disable the system to page the transmitter when alarm is triggered. For model T-7001-TW, press the button , AUX
together you will hear 2 beeps . Paging transmitter is now OFF . Press again , you will hear 1 beep , paging transmitter in ON .
For model T-7001-TW-LCD, press button "F" and "S" together , antenna icon will disappear on LCD screen . Paging mode is
OFF , To reactivate this function ,press on "F" and "S" again . Antenna icon will re-appear on LCD screen . Paging mode is ON
IMPORTANT NOTE: :
When this function is enable, there is NO ANY SIGNAL will send back to transmitter when alarm is in progress but the
another like door lock , door unlock , etc , still remain same
Page 7
7
TRANSMITTER OPERATIONS
FUNCTION PRESSING BUTTON AUDIBLE SOUND AND
TONE FEEDBACK TO
TRANSMITTER
ACTIVATION
BUTTON ARM/LOCK:
ARMING NO CHIRP
Press once 1 Hi/Lo beep
¦ Arm & lock ON
System armed and doors
locked without chirp
ARMING WITH CHIRP
Press twice 1 Hi/Lo beep
¦ Arm & lock ON
System armed and doors
locked with 1 chirp
PANIC MODE
Press 2 seconds while ignition
OFF
15 seconds alarm beep
¦ Paging ON
Panic mode activation
BUTTON DISARM/UNLOCK:
DISARMING NO CHIRP
Press once 1 Hi/Lo beep
¦ Arm: OFF & unlock: ON
System disarmed and doors
unlocked without chirp
DISARMING WITH CHIRPS
Press twice 2 Hi/Lo beeps
¦ Arm: OFF & unlock: ON
System disarmed and doors
unlocked with 2 chirps
TRUNK OPEN
Press 2 seconds 3 Hi/Lo beeps Trunk opened
BUTTON START:
OPTIONS
Press once 1 Cricket sound beep Send signal to open sliding
door or remote start engine or
trunk release or the another
function
TEMPORARY VALET MODE
Press twice while system
disarm
4 Hi/Lo beeps System keep disarm temporally
until pressing
Page 8
8
TRANSMITTER OPERATIONS
BUTTON AUX AUXILIARY ( for T-7001-TW transmitter ):
OPTIONS
Press once 3 Hi/Lo beeps Send signal to open sliding
door or remote engine
starting or trunk release or
the another function
¦ For T-7001-TW-LCD transmitter icons display only.
PAGING SIGNALS TO TRANSMITTER:
1 Hi/Lo beep
Automatic arming or security rearm engaged
5 Hi/Lo beeps
Alarm has been triggered while you were away
15 Long beeps
Alarm in progress or panic mode is engaged or paging transmitter via call button built-in receiver
1 Cricket sound
Open sliding door or remote start engine or the another function
3 Hi/Lo beeps
When trunk is released
AUDIBLE SIGNALS EMITTED BY TRANSMITTER:
3 Double beeps
Error signal or Out of Transmitted Range
3 Intermittent
beeping
Low battery indicator . Change the battery as soon as possible with AAA battery X 1 ( See
Important Note )
IMPORTANT NOTE: If you have 3 intermittent beeping on your transmitter after every confirmed feed back signal ( Hi/Lo
beep , cricket sound ), you have to replace battery .
To reset transmitter, remove the battery then put it back so that you can disarm your vehicle then Replace battery as soon as
possible.
Page 9
9
FEATURES AND OPERATIONS
ARMING:
Arming the system will also enable the starter kill and lock the doors, if installed. You can select silent or audible arming
(programmed by installer). If you try to arm the system and you hear 3, 4 or 5 beeps, one of the protected zones is opened. The
system will ignore the defective zone and force the system to arm. Consult your installer to check your system and all entry points
PASSIVE ARMING:
If selected, the system will automatically arm itself 30 seconds after the ignition has been turned OFF and the last door closed.
DISARMING:
Disarming the system will also disable the starter kill and unlock the doors, if installed. If you hear 5 beeps when you disarm the
system, it is means the alarm has been triggered while you were away.
SAFETY REARMING:
If you disarm the system by accident and you do not open any access (doors, hood), it will rearm automatically after 30 seconds,
unless the engine is running.
STARTER DISABLE OPERATION:
When the system is armed manually or by passive arming the starter kill will arm at the same time.
PANIC MODE:
With engine not running, keep pressing button for 2 seconds: panic mode is engaged. The horn or siren will be triggered. To
stop the panic mode simply press button.
Page 10
10
FEATURES AND OPERATIONS
VALET MODE:
To disarm the system in case of transmitter loss or for vehicle servicing, you must perform the sequence twice to enable the valet
mode. The first time will disarm the alarm and the second time will enable the valet mode. Under valet mode, door locks, remote
start, trunk are still functional.
TO ACTIVATE OR DE-ACTIVATE VALET MODE:
VIA TRANSMITTER:
Step 1: Turn key ignition to ON position and do not start the engine, you have 15 seconds to do step 2 and step 3.
Step 2: Keep pressing the button for 2 seconds, vehicle horn or siren will emit 5 beeps.
a. When valet mode is enabled: L.E.D. turns ON steady.
b. To deactivate valet mode repeat steps 1, 2 : L.E.D. will turn OFF.
Note: if 15 seconds expire just turn off the ignition key, then start from step #1
VIA VALET SWITCH:
Step 1: Put ignition to ON and do not start the engine, you have 15 seconds to do step 2.
Step 2: Press valet switch at least 3 times. Vehicle horn or siren will emit 5 beeps
a. When valet mode is enabled: L.E.D will turns ON steady.
b. To deactivate valet mode repeat steps 1 and 2 and L.E.D. will turn OFF.
Note: if 15 seconds expire just turn off the ignition key, then start from step #1
Page 11
11
FEATURES AND OPERATIONS
IGNITION LOCK:
Doors locks automatically 30 seconds when ignition is ON. Doors will unlock when ignition is turned OFF (ask your dealer for this
feature).
SHOCK SENSOR PRE-WARNING:
Siren/Horn chirps rapidly when shock sensor is triggered. If shock sensor is triggered for a second time within 10 seconds, the
siren or horn will sounds for 30, 60 or 120 seconds (depend on the setting time , programmed by your installer).
PAGING TRANSMITTER:
When pressing anytime button located on the receiver, system will page the transmitter. This function is useful when you are
waiting on the vehicle and want to call the people who carry the transmitter .
Page 12
12
NOTES
_______________________________________________________________________________________________________
_______________________________________________________________________________________________________
_______________________________________________________________________________________________________
_______________________________________________________________________________________________________
_______________________________________________________________________________________________________
_______________________________________________________________________________________________________
_______________________________________________________________________________________________________
_______________________________________________________________________________________________________
Loading...