Page 1
AP Router
1
DC 12V Power Adapter
1
Antenna
2
PoE DC Injector
1
Paper QIG
1
Manual/QIG CD
1
POWERLINK PL-APN High Power 802.11bgn AP Router
Quick Installation Guide
Part I: External Installation Direction
Package Content
www.premiertek.com
Page 2
POWERLINK PL-APN High Power 802.11bgn AP Router
AP Router Connection
Before installing the router, connect your PC to the internet through your broadband service. (If
there is any problem, contact your ISP.)Then proceed through the following steps.
1. Turn off your PC(s), cable/ ADSL modem and the router.
2. Adjust the antenna if needed. Normally, straight up on router is good.
3. Connect the PC(s) and each switch/hub on your local area network to the LAN ports on the
router.
4. Connect the ADSL/DSL/cable modem to the router WAN port.
5. Connect the power adapter between the DC-Jack on the router and an electrical outlet. The
router will start to work automatically.
www.premiertek.com
Page 3
POWERLINK PL-APN High Power 802.11bgn AP Router
6. Turn on your PC(s) and the cable/ADSL modem.
.
The front LED indicator
www.premiertek.com
Page 4
POWERLINK PL-APN High Power 802.11bgn AP Router
AP Router configuration
The AP Router is delivered with the following factory default parameters on the Ethernet LAN
interfaces.
Default IP Address: 192.168.1.254
Default IP subnet mask: 255.255.255.0
Web login User Name: <empty>
Web login Password: <empty>
The device has three operation modes (Gateway/Bridge/WISP).
The default IP addresses for the device are 192.168.1.254, so you need to make sure the IP
address of your PC is in the same subnet as the device, such as 192.168.1.X.
It will take about 55 seconds to complete the boot up sequence after power on.
www.premiertek.com
Page 5
POWERLINK PL-APN High Power 802.11bgn AP Router
PoE DC Injector Configuration
POE means Power over Ethernet, usually used with Wireless Device.
You can use it to integrate the power and the Ethernet then connected with the RJ45 cable.
With POE, you can bring the power and Ethernet with long distance as far as the length of RJ45
cable.
Since you used PoE DC Injector, the cable line won’t perplex you anymore. Your Access Point &
Router are installed conveniently to gain more efficient bandwidth by yourself.
Less space and electricity limitation, more comfortable wireless life.
www.premiertek.com
Page 6
POWERLINK PL-APN High Power 802.11bgn AP Router
Part II: Internal Web Management
AP Model Setup (ADSL)
1、 Install the antenna & power adapter, and then connect the LAN cable with LAN port of this
equipment. Another side of cable line connects with network card of computer. Waiting for
booting around 20 seconds.
2、 Open the IE ( Internet Explorer) and type 192.168.1.254 on Website to enter the setup frame. If
you can’t enter to setup frame, please press Reset button around 10 seconds to restore AP
and try to enter again.
Select the Setup Wizard on the left side of setup frame and press Next>>
www.premiertek.com
Page 7
POWERLINK PL-APN High Power 802.11bgn AP Router
1. In Operation Mode, select Gateway and press Next>>
2. In Time Zone Setting, if you don’t need any change, please press Next>>
www.premiertek.com
Page 8
POWERLINK PL-APN High Power 802.11bgn AP Router
3. In LAN Interface Setup, you may change the setting of IP address, DHCP and etc.
then press Next>>
4. In WAN Interface Setup, select PPPoE for your connection of WAN Access Type and enter User
Name & Password which presented by your ISOP. And then press Next>>
5. In Wireless Basic Setting, select AP for your Mode and change your SSID setup,
then press Next>>
www.premiertek.com
Page 9
POWERLINK PL-APN High Power 802.11bgn AP Router
6. In Wireless Security, select your setup of wireless security (WEP, WPA) and press Finished to
reboot around 20 seconds.
www.premiertek.com
Page 10
POWERLINK PL-APN High Power 802.11bgn AP Router
Note: You have to connect ADSL cable with WAN port of this equipment.
=============================================================
AP Model Setup (IP Share)
1、 Install the antenna & power adapter, and then connect the LAN cable with LAN port of this
equipment. Another side of cable line connects with network card of computer. Waiting for
booting around 20 seconds.
2、 Open the IE ( Internet Explorer) and type 192.168.1.254 on Website to enter the setup frame. If
you can’t enter to setup frame, please press Reset button around 10 seconds to restore AP
and try to enter again.
Select the Setup Wizard on the left side of setup frame and press Next>>
www.premiertek.com
Page 11
POWERLINK PL-APN High Power 802.11bgn AP Router
1. In Operation Mode, select Bridge and press Next>>
www.premiertek.com
Page 12
POWERLINK PL-APN High Power 802.11bgn AP Router
2. In Time Zone Setting, if you don’t need any change, please press Next>>
www.premiertek.com
Page 13
POWERLINK PL-APN High Power 802.11bgn AP Router
3. In LAN Interface Setup, you may change the setting of IP address, DHCP and etc. then press
Next>>
4.In WAN Interface Setup, select DHCP Client for your connection of WAN Access Type and press
Next>>
www.premiertek.com
Page 14
POWERLINK PL-APN High Power 802.11bgn AP Router
5. In Wireless Basic Setting, select AP for your Mode and change your SSID setup, then press
Next>>
6. In Wireless Security, select your setup of wireless security (WEP, WPA) and press
Finished to reboot around 20 seconds.
www.premiertek.com
Page 15
POWERLINK PL-APN High Power 802.11bgn AP Router
Select the TCP/IP Settings from left side of setup frame and choice LAN Interface.
Then choosing Disable from DHCP and press Apply Changes to reboot around 20 seconds to
complete the setup.
Note: Please connect cable line with LAN port when you use this equipment to connect
IP Share.
www.premiertek.com
Loading...