Powerline Control Systems SST-15 Quick Start Guide

Programming Guide
Sunrise Sunset Timer
Model – SST-15
FUNCTION
SimpleWorx products are designed to provide the most simplistic remote control lighting without running ANY new wiring. These products also remote control electrical loads the same way with absolutely no new wiring needed. They connect or what we call “link” to each other by communicating over the existing electrical power wires already in place.
Each transmitter can be linked to as many receivers as you please. Each receiver has the ability to link up to eight transmitters.
The SST Sunrise Sunset Timer (Image 1) is capable of turning 120VAC devices ON and OFF based on one of the ten preset schedules. This p from eight SimpleWorx Transmitters.
Once the SST is “linked” to a SimpleWorx transmitter (refer to “Linking a Transmitter to a Receiver”), it is capable of ha
ving its load turned ON or OFF remotely or
as if it were its very own load.
FEATURES
Scheduling:
o Choice of 10 Different Daily Programs o Daylight Savings and Leap
Remotely controlled from any SWX Transmitter
Manual overri
Astronomic D
o
o 0
-60o for Northern and Southern latitudes
o
-125o Eastern to Western longitudes
o 65
o
& 165o for Alaska and Hawaii
o 135
Power Outage Backup:
o 10 Year 125m o Permanent sc
Simple button press set-up and review of:
o Schedule o Latitude and
Built for Professional Use:
o Operating Temperature -40 o Internal High Temperature
-185
-167
10 YEAR WARRANTY
de button for local control
aily Dusk/Dawn calculations for:
A Battery
hedule retention
/Time Zone/Daylight Saving Time
Longitude/Clock Time Setting
o
F (85o C) – Shut OFF
o
F (75o C) – Reset ON
roduct can also be controlled
Year Compensation
o
F to +140o F
Protection
(Image 1)
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products basic safety precautions should always be followed, such as the following:
1. Do not use this product for other than its intended
purpose.
2. Keep away from water.
If the product comes in contact with water or other liquid, turn off the circuit breaker and remove the product immediately.
3. Never use p
roducts that have been dropped or
damaged.
INSTALLATION
To install the SST:
1. Locate the load to be cont
rolled and plug it into the
outlet on the bottom of the SST.
Note - The Load current rating (or combined rating of multiple connected devices) must not exceed 15 Amps.
2. Plug the SST into an unswitched wall outlet.
3. Turn the load
power switch to its ON position.
CAUTION: Do not insert metal objects into the module while it is connected to power.
BASIC OPERATION
The “LINK” button, below the Status LED on the front of the unit is used for a variety of functions:
For manual operation, pressing the “Link” button
will toggle between turnin
The “Link” button is also used to enter programming
and setting the values, as SimpleWorx Transmitters.
g the outlet ON and OFF.
well as linking the SST to eight
©2013 Powerline Control Systems, Inc.
All Rights Reserved v1.00
19201 Parthenia St. Suite J
P: 818.701.9831 F: 818.701.1506
pcssales@pcslighting.com
www.pcslighting.com
Programming Guide
Sunrise Sunset Timer
Model – SST-15
PROGRAMMING
Step Action Write your
choice here
#1
#2
#3
#4
#5
#6
#7
Press and hold the SST Link button for 6 seconds. (Enters Link Mode)
Tap the Link Button (3) times quickly. (Enters Program Mode)
Tap the LINK button from (1-10) times to select the desired Schedule (see Schedule Table)
Tap the LINK button (1-6) times to select the desired Time Zone (see Time Zone Table)
Tap the push button (1) USA ENABLE, (2) MEXICO ENABLE or (3) DISABLE to set if your location uses Daylight Savings Time (DST)
Tap the push button (1-14) times to select the desired Longitude (East/West, see Longitude table)
Tap the push button (1-12) times to select the desired Latitude (North/South, see Latitude table)
N/A The LED will then flash GREEN and flash its load (if
N/A The lighting load will Blink and the LED will
Schedule
Time Zone
DST
Longitude
Latitude
Response
a load is connected).
change to blinking RED. The Status LED pulses GREEN (1-10) times to
confirm selection, then the Status LED will return to blinking RED.
The Status LED pulses (1-6) times GREEN to confirm selection, then the Status LED will return to blinking RED.
The Status LED pulses (1 or 3) times GREEN to confirm selection, then the Status LED will return to blinki
The Status LED pulses (1-14) times GREEN to confirm selection, then the Status LED will return to blinki
The Status LED pulses (1-12) times GREEN to confirm selection, the load indicate your programming is complete and then the Status LED will return to solid RED.
ng RED.
ng RED.
will toggle once to
REVIEW ALL SETTINGS MODE
#1
Tap the Link Button (3) times quickly. The LED will turn off and then begin to flash GREEN (1-14) times to
confirm your selections for Schedule, Time Zone, DST, Longitude and
Latitude with a pause between each selection. Once completed, the load will toggle once to indicate this operation is complete and the LED returns to solid RED.
SCHEDULE TYPE ONLY PROGRAMMING (WITHOUT PROGRAMMING LOCATION AGAIN)
Step Action Write your
choice here
#1
#2
#3
Press and hold the SST Link button for 6 seconds. (Enters Link Mode)
Tap the Link Button (4) times quickly. (Enters program mode)
Tap the LINK button from (1-10) times to select the desired Schedule (see Schedule Table)
©2013 Powerline Control Systems, Inc.
All Rights Reserved v1.00
N/A The LED will then flash GREEN and flash its load (if
N/A The lighting load will Blink and the LED will be
The Status LED pulses (1-10) times GREEN to
Response
a load is connected).
blinking Orange.
confirm your selection, the load will toggle once to indicate programming is complete and then the Status LED will return to solid RED.
P: 818.701.9831 F: 818.701.1506
19201 Parthenia St. Suite J
pcssales@pcslighting.com
www.pcslighting.com
Programming Guide
Sunrise Sunset Timer
Model – SST-15
PROGRAMMING TABLES
Schedule: ON/OFF #1 ON/OFF #2
1 tap SUNRISE
SUNSET
2 taps SUNSET–30 Min
SUNRISE +30 Min
3 taps SUNSET
MIDNIGHT
4 taps SUNSET
10:00PM
5 taps SUNSET
2:00 AM
6 taps SUNSET
MIDNIGHT
7 taps SUNSET
MIDNIGHT
8 taps SUNSET
MIDNIGHT
9 taps SUNSET
10:00 PM
10 taps SUNSET
10:00 PM
Time Zone:
1 tap = Eastern (UTC-5) 2 taps = Central (UTC-6) 3 taps = Mountain (UTC-7) 4 taps = Pacific (UTC-8) 5 taps = Alaskan (UTC-9) 6 taps = Hawaiian (UTC-10)
Daylight Savings Time ( DST):
1 tap = Enable DST Adjustment (USA) 2 taps = Enable DST Adjustment (MEXICO) 3 taps = Disable DST Adjustment
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
SUNRISE -30 Min SUNRISE
SUNRISE -60 Min SUNRISE
SUNRISE -30 Min SUNRISE +30 Min
SUNRISE -60 Min SUNRISE +30Min
SUNRISE -30 Min SUNRISE +30 Min
Longitude: (East/We
1 tap = 121-125 degrees 2 taps = 116-120 degrees 3 taps = 111-115 degrees 4 taps = 106-110 degrees 5 taps = 101-105 degrees 6 taps = 96-100 degrees 7 taps = 91-95 degrees 8 taps = 86-90 degrees 9 taps = 81-85 degrees 10 taps = 76-80 degrees 11 taps = 71-75 degrees 12 taps = 65-70 degrees 13 taps = 155-158 degrees (Hawaii) 14 taps = 135 degrees (Juno AK)
Latitude: (Nort
1 taps = 56-60 degrees 2 taps = 51-55 degrees 3 taps = 46-50 degrees 4 taps = 41-45 degree 5 taps = 36-40 degrees 6 taps = 31-35 degrees 7 taps = 26-30 degrees 8 taps = 21-25 degrees 9 taps =16-20 degrees 10 taps = 11-15 degrees 11 taps = 6-10 degrees 12 taps =0-5 degrees
st) -
h/South)
LONGITUDE-LATITUDE MAP
The PMR will automatically perform Daylight Saving Time (DST) adjustments if DST adjustments are enabled:
If USA DST
o Increme
o Decrem
If Mexican DST
o Increme o Decrem
is enabled:
nt 1 Hour at 2 AM on the 2nd Sunday in March
ent 1 Hour at 2 AM on the 1st Sunday in November
is enabled:
nt 1 Hour at 2AM on the 2nd Sunday in April
ent 1 Hour at 2AM on the 1st Sunday in October
©2013 Powerline Control Systems, Inc.
All Rights Reserved v1.00
Upon setting the longitude and latitude the sunrise and sunset times will be within 10 minutes of actual time.
19201 Parthenia St. Suite J
P: 818.701.9831 F: 818.701.1506
pcssales@pcslighting.com
www.pcslighting.com
Programming Guide
Sunrise Sunset Timer
Model – SST-15
CLOCK REVIEW MODE
The SST clock has been preset at the factory. The time and schedule settings will be maintained for 10 years if/when disconnected from electrical power. Once a schedule has been selected it will run daily. The real time clock will be adjusted
to match the local time, based on the selected time zone
1 Tap the Link Button (8) times quickly.
2 The LED will turn off and then begin to flash GREEN
to represent the following four items to confirm the current clock settings. Hour, Minute, Month, Day with a pause between each selection.
NOTE:
The LED flashes 1 time to represent a "1
to represent a "2", etc.
The LED flashes 10 times to represent a "0".
Hour (00-23) displayed in two LED flashings:
10's of Hours (0-2) 1's of Hours (0-9)
Minute (00-59) displayed in two LED flashings:
10's of Minutes (0-5)
1's of Minutes (0-9) Day of-Week (1-7) 1=Sunday, 2=Monday Month (01-12) displayed in two LED flashings:
10's of Month (0-1)
1's of Month (0-9) Day (00-31) displayed in two LED flashings:
10's of Days (0-3)
1's of Days (0-9) Year (00-99) displayed in two LED flashings:
10's of Year (0-9)
1's of Year (0-9)
3 Once completed the LED returns to solid RED and the
load will toggle once to indicate this operation has
been completed.
", and flashes 2 times
STATUS LED INDICATOR
LED Color Status
Solid RED Power applied to Module
Blinking GREEN Device is in LINK Mode
Solid GREEN Transmitting a SPC™ message
Blinking RED In Programming Mode
Blinking ORANGE In Re-Schedule Mode
Slowly Blinking RED Temperature Protection is Activated
.
LINKING MODE
All SimpleWorx transmitters can remotely control one or more SimpleWorx Receiver(s). Follow the steps below to “LINK” the two together:
To enter Link Mode:
1 At the SimpleWorx Transmitter: Press and hold its Link
button for 6 seconds. The LED and flash its load (if a
2 At the SimpleWorx Receiver: Press and hold the
rocker switch or link button for 6 seconds. The LED will flash GREEN and flash its load (if a load is connected).
3 The Receiver will indicate (within 30 seconds) the two
devices have automatically “LINKED” to one another when the LED stops flashing and then flashes its load once.
4 The Transmitter may be taken out of “LINK” mode by
tapping its rocker switch or link button once. The LED will stop flashing and flashes its load (if a load is connected).
Note: The TX will automatically timeout after 5 min.
load is connected).
will then flash GREEN
FACTORY RESET
1 Press and hold its Link button for 6 seconds. The LED
will then flash GREEN and flash its load (if a load is connected).
2 Tap the Link Button (10) Ten times quickly. 3 The LED will blink RED 10 Times; the load will toggle
once, and returns to solid RED to indicate this operation is complete.
NOTE: This will erase all transmitters the SST was linked to.
CERTIFICATION
This product has been thoroughly tested by Intertek Testing Services, a nationally recognized independent third-party laboratory. The Northern American ETL listed mark signifies that the product has been test4ed to and has met requirements of a widely recognized consensus of US and Canadian product safety standards.
LIMITED WARRANTY
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in materials and workmanship for a period of five years from the date of purchase. Refer to the warranty information on the PCS website (www.pcslighting.com) for exact details.
©2013 Powerline Control Systems, Inc.
All Rights Reserved v1.00
19201 Parthenia St. Suite J
P: 818.701.9831 F: 818.701.1506
pcssales@pcslighting.com
www.pcslighting.com
Loading...