HAI UPB™ Wall Switch and Auxiliary Switch
Installation and Operating Instructions
For the following Models:
35A00-1 HAI 600W Dimmer Switch, 35A00-1CFL 600W CFL/LED Dimmer, 35A00-3 HAI 600W Non-Dimming Switch (collectively referred to
as HAI UPB™ Wall Switch, in this document), and 37A00-1 HAI Auxiliary Switch
READ THESE INSTRUCTIONS BEFORE INSTALLING DEVICE
This HAI UPB™ Wall Switch and Auxiliary Switch is intended for installation in accordance with the National Electrical Code and local codes and
regulations. It is recommended that a qualified electrician perform this installation. Retain these instructions for reference.
To reduce the risk of overheating and possible damage to other equipment, when configured as dimming-capable, do not install to control a
receptacle, a motor-operated appliance, or a transformer-supplied appliance.
This product is for indoor use only. Connect only copper wire to this device.
Important Notes Prior To Installation
1. All HAI UPB™ Wall Switches require a neutral (white) connection wire.
2. Be sure that all power to the load has been disconnected by turning off the circuit breaker. Installing an HAI UPB™ Wall Switch or Auxiliary
Switch with power on may expose you to dangerous voltage and may damage the device.
HAI UPB™ Wall Switch Overview
The HAI UPB™ Wall Switch (Figure 1) allows for local control of lighting by using the Decora-style rocker switch. It also incorporates the UPB™
two-way powerline communication technology that gives it the ability to be remotely controlled by UPB™ compatible controllers. The HAI UPB™
Wall Switch is also capable of transmitting UPB™ messages (including current light level) when the rocker switch is turned on, turned off,
brightened, or dimmed.
Each switch can be configured to custom fit an individual’s lifestyle and desires. The HAI Dimmer Switch is capable of storing up to 16 preset light
levels and fade rates to create powerful lighting scenes. The HAI Non-Dimming Switch is used to control such loads as fluorescent lights and ceiling
fans.
LED
INDICATOR
GREEN
GROUND
BLACK
GRAY
BLUE
YELLOW
BLACK
WHITE
RED
YELLOW
LINE
NEUTRAL
LOAD
CONTROL
LINE
*NEUTRAL
(FOR RED INDICATOR)
*NEUTRAL
(FOR BLUE INDICATOR)
CONTROL
TOP
(ON/BRIGHT)
BOTTOM
(OFF/DIM)
AIR-GAP SWITCH
LEVER GROOVE
Figure 1 - HAI UPB™ Wall Switch
HAI Auxiliary Switch Overview
The 37A00-1 HAI Auxiliary Switch (Figure 2) is an optional companion device used with the HAI UPB™ Wall Switch for multi-way circuits. The
HAI Auxiliary Switch has a Decora-style rocker switch that controls the lighting load in the exact same manner as the Decora-style rocker switch on
the HAI UPB™ Wall Switch.
LED
INDICATOR
TOP
(ON/BRIGHT)
BOTTOM
(OFF/DIM)
Figure 2 – HAI Auxiliary Switch
Changing Switch Color
The color of the HAI UPB™ Wall Switch and Auxiliary Switch may be changed to complement the interior décor. The HAI UPB™ Wall Switch
and Auxiliary Switch is supplied with a white switch plate. Additional colors are available; contact your HAI distributor for more information. When
changing the switch plate, make sure that the switch is disconnected from all power, and proceed as follows:
The switch plate attaches to the HAI UPB™ Wall Switch and Auxiliary Switch with two latches on the right and two on the left. Using a smallbladed screwdriver, gently depress the upper and lower latch on one side while lifting up on the plate. Once the latches are released on one side,
remove the switch plate from the other side.
1. Align the latches of the new switch plate to the openings on the mounting plate and gently snap into place.
INSTALLATION INSTRUCTIONS
The HAI UPB™ Wall Switch is wired directly to the lighting circuit and can be controlled by adding one or more optional HAI Auxiliary Switches
producing multi-way circuits. Multi-way circuits make it possible for a group of switches to control the same light or set of lights. This section will
illustrate how to make the connections.
Notes:
1. Refer to Figures 1 and Figure 2 to determine the wire colors for each connection.
2. All HAI UPB™ Wall Switches require a neutral (white) connection.
3. The Line (black) wire must be accessible for the installation of all HAI Auxiliary Switches. This wire may be connected to either phase of the
120/240V supply. The blue and/or gray wire on the HAI Auxiliary Switch can be connected to either earth ground or neutral. The blue and/or
gray wire is only used to light the LED on the switch. This LED only indicates that power is applied and serves as a ni ght-light. Connect the
blue wire only to light the LED blue. Connect the gray wire only to light the LED red. Connect both the blue wire and the gray wire to light
Air-Gap Switch Lever
The HAI UPB™ Wall Switch has an air-gap switch lever that will remove all power from the load for safe switch
installation and light bulb replacement. To activate the air-gap switch, using your fingernail, pr y open the lever at
the groove (Figure 1). Swing the lever fully open so that it is perpendicular to the bottom rim (Figure 4). After
servicing, push the lever fully closed so that it is parallel to the bottom rim. The lever must be pushed fully closed
for normal operation.
Figure 4 – Air-Gap Switch Lever
Installation Procedure
1. Be sure that all power to the load has been disconnected by turning off the circuit breaker.
2. If applicable, remove the faceplate from the existing wall switch, remove the existing wall switch from the wall box, and disconnect the wires
from the existing wall switch. Identify the “Line”, "Neutral", "Load" and “Traveler” (if applicable) wires.
3. Be sure that the air-gap switch lever on the HAI UPB™ Wall Switch is fully open.
4. Remove ¾” of insulation from each of the wires on the HAI UPB™ Wall Switch. Install the HAI UPB™ Wall Switch by connecting wires
per wiring configuration shown in Figure 5.
5. Install any optional HAI Auxiliary Switch per wiring configuration shown in Figure 5.
Figure 3 – Changing Switch Color
the LED magenta.
6. After all connections have been made, be certain that all wire connectors are firmly attached and there is no exposed copper.
7. Gently place the wires and HAI UPB™ Wall Switch into the wall box with the LED at the top of device. Using the supplied screws, attach
the HAI UPB™ Wall Switch to the wall box.
8. Before installing the faceplate, restore power to the circuit, and then fully close the air-gap switch lever.
9. After testing the HAI UPB™ Wall Switch and Auxiliary Switch for proper local operation (see Table 2 and Table 3), install a Decora-style
faceplate over each switch.
HAI UPB™ Wall Switch De-Rating
In two-gang installations, there is no need to de-rate the 35A00-1, 35A00-1CFL, or 35A00-3. In three-gang installations, each switch must be derated from 600W to 500W.
Model Device Maximum Load Next to One Dimmer Next to Two Dimmers
35A00-1 600W 600W 500W
35A00-1CFL 600W 600W 500W
35A00-3 600W 600W 500W
Table 1 – HAI Wall Switch De-Rating
HAI DIMMER SWITCH OPERATION
The HAI Dimmer Switch has many configurable items that can be set using the UPB™ UPStart configuration software. The following describes the
operation of the HAI Dimmer Switch in its factory default configuration.
Local Rocker Switch Operation
The HAI Dimmer Switch has a Decora-style rocker switch that can be used to control the lighting load as follows.
Rocker Event Top Rocker Bottom Rocker
Single-Tap
Double-Tap Snaps the light to 100% (on) and overrides auto shut-off. Snaps the light to 0% (off).
Hold
Release
Table 2 - HAI UPB™ Dimmer Switch Local Operation
Brightens the light to 100% (on) at default fade rate and restarts
auto shut-off timer (if applicable).
Starts fading (brightening) the light towards 100% at default fade
rate and restarts auto shut-off timer (if applicable).
Stops brightening the light and restarts auto shut-off timer (if
applicable).
Fade the light to 0% (off) at default fade rate.
Starts fading (dimming) the light towards 0% at
default fade rate.
Stops dimming the light.
HAI NON-DIMMING SWITCH OPERATION
The HAI Non-Dimming Switch has many configurable items that can be set using the UPB™ UPStart configuration software. The following
describes the operation of the HAI Non-Dimming Switch in its factory default configuration.
Local Rocker Switch Operation
The HAI Non-Dimming Switch has a Decora-style rocker switch that can be used to control the load as follows.
Rocker Event Top Rocker Bottom Rocker
Single-Tap Turns the load on and starts auto shut-off timer (if applicable). Turns the load off.
Table 3 – HAI Non-Dimming Switch Local Operation
LED Indicator
The HAI UPB™ Wall Switch comes equipped with a multi-color LED indicator that is normally lit to blue when the load is off. The LED will turn
off when the load is turned on or set to any level above 0%. The LED will flash magenta while the auto shut-off timer is running (if the configured
LED option is always off, the LED will remain off during the timeout period).
If used, the LED in the HAI Auxiliary Switch is always lit.
HAI AUXILIARY SWITCH OPERATION
The HAI UPB™ Wall Switch can be connected to one or more HAI Auxiliary Switches producing multi-way lighting circuits. Each HAI Auxiliary
Switch has a Decora-style rocker switch that controls the lighting load in the exact same manner as the Decora-style rocker switch on the connected
HAI UPB™ Wall Switch, as previously described. When connected, the LED remains continually on at all times while power is applied.
Setup Mode
To configure the HAI UPB™ Wall Switch using an HAI controller or a PC running the UPB™ UPStart configuration software, it must be put into
Setup Mode as follows:
Table 4 – HAI Wall Switch Setup
Note:
Setup mode and blink mode take precedence over auto shut-off. If the auto shut-off timer is running, and then either setup mode or
blink mode occurs, the auto shut-off timer will be reset and disabled until setup or blink mode expire.
Step Operation
1 Tap the rocker switch quickly 5 times
The HAI UPB™ Wall Switch will flash the lighting load one time and blink its LED blue to indicate that it is in Setup Mode.
2
Note: the switch will automatically exit Setup mode after 5 minutes.
35I00-1, Rev C
LINE
37A00 (OPTIONAL)
AUXILIARY SWITCH
BLACK BLACK
37A00 (OPTIONAL)
AUXILIARY SWITCH
YELLOW
35A00
HAI Wall Switch
BLACK
YELLOWYELLOW
Line 120VAC, 60Hz
*BLUE AND/OR GRAY*BLUE AND/OR GRAY
NEUTRAL
*CONNECTING THE BLUE AND/OR GRAY WIRE TO NEUTRAL SETS THE COLOR OF THE LED INDICATOR.
CONNECT BLUE FOR BLUE INDICATOR, GRAY FOR RED INDICATOR, OR BOTH FOR MAGENTA INDICATOR.
BLUE AND/OR GRAY WIRE MAY BE CONNECTED TO NEUTRAL OR EARTH GROUND. NEUTRAL IS RECOMMENDED.
Reset to Factory Default Settings
To reset the HAI UPB™ Wall Switch to factory default settings:
Step Operation
1 On the HAI UPB™ Wall Switch that you want to reset to factory default, tap the rocker switch quickly 5 times.
2 The HAI UPB™ Wall Switch will flash the lighting load one time and blink its LED blue to indicate that it is ready to be reset.
3 Tap the rocker switch quickly 10 times to reset to factory default setting.
4 The HAI UPB™ Wall Switch will flash the lighting load one time and blink its LED red to indicate that it has been reset.
5 Tap the rocker switch once more to stop the LED from blinking.
SPECIFICATIONS
Model Number 35A00-1 35A00-1CFL 35A00-3
Incandescent Loads Dimming Yes Yes Yes (configurable)
Inductive Loads Dimming Yes Yes Yes (configurable)
Florescent Loads Non-Dimming Yes (configurable) Yes (configurable) Yes
Power Maximum Dimming 600W / 600VA 600W / 600VA 600W / 600VA
Current Maximum Non-Dimming 5A 5A 5A
Connections 18 GA 18 GA 18 GA
LED Indicator Yes Yes Yes
Dimensions 4.1 x 1.75 x 1.45 4.1 x 1.75 x 1.45 4.1 x 1.75 x 1.45
Weight 0.25 lb. 0.25 lb. 0.25 lb.
Mounting Standard J Box Standard J Box Standard J Box
Input Power 120 ± 12 VAC 120 ± 12 VAC 120 ± 12 VAC
Input Frequency 60 ± 3 Hz 60 ± 3 Hz 60 ± 3 Hz
Operating Temperature -40 °F to 104 °F -40 °F to 104 °F -40 °F to 104 °F
Note: It is normal for this switch to make a slight buzzing sound during operation. It is also normal for the switch and wall plate to feel warm to the touch.
LIMITED WARRANTY
HAI warrants this product against defects in material and workmanship, under normal use and service, for a period of two (2) years from the date of purchase. During the
warranty period, HAI will repair or replace, at its sole option, if this product fails due to defect. This warranty does not cover the cost of removal or reinstallation of any product.
This warranty does not cover failure caused by normal wear, damage to the product while in your possession (other than damage caused by defect or malfunction), or by its
improper installation, including failure to follow the written installation and operation instructions, alterations, misuse, or abuse. The remedies provided for in this warranty are
the sole and exclusive remedies thereof. In no event shall HAI be liable for incidental expenses or consequential loss or damages. For the complete HAI Warranty for USA
policy, see the HAI web site at www.homeauto.com.
Any implied warranties, including warranties of merchantability and fitness for particular use or purpose are limited to a period of two (2) years from purchase date. This
warranty gives you specific legal rights, and you may have other legal rights, which vary from state to state. Some limitations may not apply to you.
For warranty and repair service within the continental United States, send defective unit carefully packaged, postage prepaid, along with description of trouble, name, return
address, and phone number to: HAI, Repair Department, 4330 Michoud Blvd, New Orleans, LA, 70129. HAI will pay return shipping charges via normal ground service.
Outside of the continental United States: Contact an Authorized Distributor for repair/replacement instructions.
GREEN
Refer to the following Table for specific manufactures and model numbers of
dimmable CFL and LED bulbs approved for use with these dimmers:
CFL / LED Lamp Manufacturer Lamp Model Lamp Wattage (W)
CFL EcoSmart 2R3015DIM 15
CFL EcoSmart ES5CCDF052 5
CFL EcoSmart ES5M10123 23
CFL EcoSmart ES5R315DIM35K 15
CFL EcoSmart ES5R315DIM50K 15
CFL Feit BPESL15T/DM 15
CFL Feit BPESL23T/DIM 23
CFL GE / Energy Smart FLE15/2/DV/R30 15
CFL GE / Energy Smart FLE15HT3/2/DV/SW 15
CFL GE / Energy Smart FLE26/2/DV/R40 26
CFL GE / Energy Smart FLE26HT3/2/DV 26
CFL Litetronics 16AE5L092725 27
CFL Litetronics 18185K085141 5
CFL Litetronics 18185K088141 8
CFL Litetronics 18505A10111 11
CFL Litetronics 18BR5E09152 15
REDWHITE
CFL Litetronics / EarthMate E05129LW 5
CFL Litetronics / EarthMate E2752AJLW 27
CFL Neptun 61920-ADIM 20
CFL Neptun / EarthTronics CF24SW1BDIM 24
CFL Phillips EL/A PAR38 20
CFL Phillips EL/A R30 DIM 16
CFL Phillips EL/A R40 DIM 20
CFL Sylvania CF5EL/A15/827/DIM/BL 5
CFL Sylvania CF5EL/B10/827/C/ADP/DIM/BL 5
CFL Sylvania CF14EL/R20/DIM 14
CFL Sylvania CF14EL/TWIST/DIM 14
CFL Sylvania CF19EL/BR40/DIM 19
CFL Sylvania CF24EL/TWIST/827/DIM/RP 24
CFL TCP 2R2014DIM 14
CFL TCP 40123 23
CFL TCP 4R3016TD 16
CFL TCP CCA05 5
CFL ULA SDR23W2P-R30 DIM 23
LED Cooper Lighting - HALO ML706830 14
LED Cree CR6-0210E 12
LED Cree CR6-0323E 12
LED EcoSmart ECO-GU24-575L-YOW 12
LED EcoSmart G2510003-005 8
LED EcoSmart R2010010-013 8
LED Lemnis Lighting Pharox 300 6
LED Phillips 12E26A60 12.5
LED Phillips 3E12B1 1-E 3
LED Phillips 6E26R20 6
LED Phillips 7E26PAR20-E 7
LED Phillips 8E26A60 8
LED Sylvania LED8PAR20/DIM/827/FL36 8
LED Sylvania LED8PAR20/DIM/827/NFL25 8
LED Sylvania LED8PAR20/DIM/830/NFL25/HVP 8
LED Sylvania LED10PAR30/DIM/SG830/WSP15 10
LED Sylvania LED11PAR30/DIM/SG/830/SP10 11
LED TCP LDA153WH30K 3
LED Toshiba 218-50053 7.8
LED Utilitech 0171150 2
LED Utilitech 0338802 7.5
LED Utilitech 0352280 3.5
CFL = Compact Fluorescent Lamp
LED = Self Ballasted, Light-Emitting Diode
Loading...