Powerfist 11G–2–30H, 9G–2–30H, 9G–1–10TT, 6.5G–1–10TT, 5.5G–1–10TT User Manual

...

Download

Page 1

TABLE OF CONTENTS

SECTION DESCRIPTION PAGE

1 General Information 1

2 Safety Guidelines 2

3 Operation 3

4 Maintenance 9 5 Troubleshooting 12 6 Specifications 14 7 Assembly Parts List 18 8 Pump Parts List 30

1. GENERAL INFORMATION

Congratulations on your choice of a Powerfist Compressor. This equipment has been designe d and manufactured to meet the light industrial and consumer needs of air compressors.

Safe, efficient and trouble free operation of your Compressor requires that you and anyone else who will be operating and maintaining the machine, read and understand all of the safety, operation maintenance and troubleshooting information contained within this Operator’s Manual.

WARRANTY- PARTS - SERVICE

If you experience any problems and need assistance or parts and repair service please contact Princess A uto Ltd. at:

Telephone # 1-800-665-8685 Fax # 1-800-265-4212

To obtain prompt, efficient service, always provide the serial number and item number of your unit. See the parts list for location of the serial number decal. Please mark the numbers in the space provided for easy reference.

SERIAL # ________________________ ITEM # ________________________

Printed in Canada 10002215-1 Issue Date: January 2007 Revision 09

Page 2

2. SAFETY GUIDELINES

DEFINITIONS

Safety symbols identify important safety messages that alert to the possibility of personal injury or death. Review them carefully before operating the unit and before performing maintenance or repairs. Check the rules and regulations at your location and identify possible hazards. The appropriate signal word for each message has been selected using the following guidelines:

- Danger indicates an immediate and specific hazard, which will result in severe personal

injury or death if the proper precautions are not taken.

- Warning indicates a specific hazard or unsafe practice, which could result in severe

personal injury or death if proper precautions are not taken.

- Caution indicates a potentially hazardous situation, which may result in minor or moderate

injury if proper practices are not taken.

____________________________________________________________________________

IMPORTANT SAFETY INSTRUCTIONS

Read and understand operator’s manual and all safety alerts before operating or maintaining your

Compressor. Be certain that everyone operating this equipment is familiar with the recommen ded operating and maintenance procedures and follows all the safety precautions. Never let children or untrained adults operate the machine.

_______________________________________________________________________________

RISK OF FIRE OR EXPLOSION

Spilled gasoline and its vapors can ignite from cigarette sparks, electrical arcing, exhaust gases, and hot engine components such as the muffler. Never refuel the engine while it is hot or running. Move unit away from refueling area before starting engine. Operate and fuel equipment in well-ventilated areas free from obstructions.

RISK OF BURSTING

Air under pressure will cause injury, death or property damage. Do not exceed pressure rating. Safety relief valve settings must not be changed, check regularly for proper operation. Do not weld, drill or modify compressor tank; it can severely impair tank strength and cause extremely hazardous conditions. Any adjustment to the tank by the user will void the warranty.

RISK OF INJURY

Do not operate with belt guard removed. Wait for all moving parts to stop before taking belt guard off for compressor servicing. Belt guard must be fastened in place before starting the compressor.

RISK OF BURNS

High temperatures are generated by the operation of the compressor. Contact with hot surfaces, such as the pump, discharge hose and engine exhaust components could result in a serious burn. Allow them to cool off before handling or servicing. Keep children away from the compressor at all times.

RISK TO BREATHING

Do not operate equipment in an enclosed area. Engine exhaust contains carbon monoxide, an odorless, colorless, deadly poison. Never directly inhale compressed air produced by a compressor. It is not suitable for breathing purposes. Read all labels when you are spraying paints or toxic chemicals and follow the safety instructions.

RISK OF HEARING AND EYE INJURY

Always wear hearing protection and approved safety goggles when using an air compressor. Failure to do so may result in hearing loss and serious injury.

Page 3

3. OPERATION

3.1 HOW THE COMPRESSOR WORKS

3.1.1 COMPONENTS

The basic components of the air compressor are the gasoline engine, pump, tank and unlo ader. The gasoline engine (item A) powers the pump. The engine drives a pulley and belt, which transfers power from the engine

to the pump pistons via a flywheel and a crankshaft. The flywheel fan helps cool the pump. The pump (item B) compresses the air and discharges it into the tank. As the piston in the pump cylinder

moves downward, air enters the cylinder through the filter and air intake valves at atmospheric pre ssure. As the piston moves upward, it compresses the air and discharges it into the tank through an unloader/check valve.

The tank (item C) stores the compressed air. A check valve at the tank inlet prevents the compressed air in the tank from flowing back into the pump.

When the air pressure in the tank reaches the factory-set limit, the unloader (item D) relieves air pressure in the pump and transfer tubes and switches the engine to idle. As compressed air is used and the pressure level in the tank drops to a pre-set level, the unloader switches the engine back to drive and the compressor resumes pumping air.

Engine E Throttle Control Cable B Pump F Pressure Gauge C Tank G Relief Valve D Unloader/ check valve

Figure 1: Air Compressor Components

Page 4

3.1.2 CONTROLS

1. Unloader/Check Valve

The unloader (see Figure 2 below) maintains pressure between the “cut-in” and “cut-out” pressure levels. At low-pressure levels, all the compressor discharge air passes through the unloader into the tank. When the tank air pressure reaches the desired cut-out pressure, the vent port in the unloader opens allowing all compressor discharge air to be vented to atmosphere. At the same time, a che c k valve internal to the unloader closes, preventing any air from leaving the tank through the vent port. As air is used from the tank, the air pressure drops until the desired cut-in pressure is reached. Then the check valve changes back to its original configuration where all the compressor discharge air is flowing through the valve into the tank. This cycle continues, maintaining tank pressures betwee n the cut-in and cut-out levels. The unloader is pre-set at the factory and should not be tampered with.

2. Pressure Relief Valves

The pressure relief valve (item G in Figure 1, page 3) aids in preventing system failures by relieving pressure when compressed air reaches a determined level. They are available in various pressure settings. Pressure relief valves are pre-set by the manufacturer and under no circumstances should the setting be changed by anyone other than the manufacturer. All pressure relief valves must be tested on a regular basis and kept clean by pulling the ring connector on the end of the valve.

3. Throttle Control Cable

The throttle control cable (see Figure 2 below) is used to slow down the driving engine. It is a small, single-acting, spring return air cylinder that moves the throttle lever on the engine to the idle position when the cylinder cable is extended in the cut-out (venting) mode.

TOGGLE-UNLOADING LEVER

IN-PORT DISCHARGE FROM COMPRESSOR

VENT PORT

OUT-PORT TO TANK

ENGINE THROTTLE CONTROL

Figure 2: Unloader/Check Valve

Page 5

3.1.3 INLET AIR SYSTEM

A clean, cool and dry air supply is essential to the satisfactory operation of your compressor. The standard air filter that the compressor is equipped with when leaving the factory is of sufficient size and is designed to meet normal conditions, when properly serviced in accordance with the maintenance section of this manual.

If however the compressor is to be installed in a location where considerable dust, dirt and other contaminants are prevalent, consult your local Distributor for advice. It is the user’s responsibility to provide adequate filtration for these conditions. Oil bath filters are not to be used.

CAUTION: Never locate the compressor where toxic, volatile or corrosive vapors, air temperatures exceeding 100 degrees F, water, or extremely dirty air could be ingested. The performance of the

compressor system could be adversely affected.

3.1.4 DISCHARGE SYSTEM

1. Discharge Pipe

The discharge piping should be of the same diameter as the compressor discharge connection, or sized so that the pressure drop at any point in the system does not exceed 10% of the air receiver pressure.

2. Auxiliary Air Receiver

Install auxiliary air receivers near heavy loads or at the far end of a long system. This will ensure sufficient pressures if the use is intermittent, or sudden large demands are placed on the system.

3. Moisture Removal and Air Filtration

As the air cools, moisture will condense in the line. This moisture must be removed before it reaches the tool being used. To remove this moisture, run the main air line downhill to a moisture trap and drain. All service line outlets should be installed above the moisture trap to prevent moisture from entering the tool or device used with the air.

4. Shut-off Valves

Install shut-off valves in each drop line to isolate the tool and its accessories for servicing. You can also install a bypass line around an accessory.

5. Air Receiver Tank

An air receiver tank stores the compressed air. WARNING! Pressure vessels must not be modified, welded, repaired, reworked or subjected to operating conditions outside the nameplate ratings. Such actions may cause property damage, severe injury or even death.

6. Drain Valve

A drain valve must be located in the bottom of the air receiver tank to allow for moisture drainage.

7. Air Pressure Gauge

The air pressure gauge on the tank measures air pressure inside the tank. Install the air pressure gauge in the drop line for each tool to regulate air pressure to the tool. Never exceed the maximum

pressure rating.

8. Air Lubrication

Install an air lubricator only for those tools requiring lubrication. DO NOT spraying or similar applications.

use a lubricator for paint

Page 6

Figure 3: Compressor Air System

Page 7

3.2 ASSEMBLY

1. Unpack the air compressor. Inspect the unit for damage. If the unit has been damaged in transit complete a damage claim.

2. Check the compressor’s item number to confirm you have received the model ordered.

3. Ensure that adequate lifting equipment is available for moving the compressor. Follow good shop practices and safety procedures.

4. Rubber feet are provided for items 8048530, 8057739 and 8077513. CAUTION! The shipping pallet is not designed as a base for an operating compressor. Remove

the compressor from the pallet and place it on the floor or a hard, level surface. The compressor must be level to ensure proper lubrication of the pump and good drainage of the moisture in the tank. We recommend the use of rubber vibration pads under the feet for stationary units.

5. The flywheel side of the compressor must be at least 12 inches (31cm) from any wall or obstruction in a clean, well-ventilated area to ensure sufficient air flow and cooling.

6. Connect discharge system components (not included) to the tank outlet.

3.3 PRE-OPERATION CHECKLIST

1. Remove all loose pieces and installation tools from the compressor and check for installation debris.

2. Unless otherwise specified, compressors are normally shipped without lubri ca nt in the crankcase. Add the correct amount of specified oil to the crankcase of the pump and the engine. Fill the tank of the gasoline engine with unleaded gasoline.

3. Check engine and compressor pulleys for alignment and tightness on shaft.

4. Manually rotate the compressor pulley several rotations to be sure there are no mechanical interferences.

5. Check belt tension.

6. Check all pressure connections for tightness and leaks.

7. Make sure all pressure relief valves are correctly installed.

8. Be sure all guards are in place and securely mounted.

9. Make sure the operating area is well ventilated.

10. Open all manual shutoff valves at and beyond the compressor discharge.

11. After all the above conditions have been satisfied, the unit can be started.

Page 8

3.4 BREAK-IN & START-UP

This instruction manual, as well as any instructions supplied by the manufacturers of supporting equipment, should be read and understood prior to starting the compressor. With the pre-operation checklist completed and satisfied proceed to start the compressor.

1. Check oil level in the crankcase. The oil level should be no lower than the center of the sight glass.

2. Check that the drain cock is open.

3. Start compressor and watch for excessive vibrations and/or strang e noises. If either exists, stop the compressor. Refer to troubleshooting for help in determining the cause of such problems.

4. Manually activate safety relief valves by pulling ring or lever.

5. Run the compressor unloaded for 20 minutes to lubricate and break-in the intern al parts.

6. Close the drain cock. Compressor will fill the tank to the cut out pressure.

7. Check the operation of controls and system pressure.

8. Observe compressor operation closely for the first hour and then frequently for the next 8 hours of operation.

9. After the first 8 hours of operation change the oil, check the belt tension and inspect the system for leaks.

WARNING! - High temperatures are generated by the operation of the compressor. Contact with hot surfaces, such as the pump, discharge hose and engine exhaust components could result in a ser ious burn. Allow them to cool off before handling or servicing. Keep children away from the compressor at all

times.

3.5 DAILY STARTING CHECKLIST

Do not proceed until the Pre-Operation Checklist and Break-In & Start-Up sub-sections have been read and are thoroughly understood.

1. Check oil level in the crankcase of compressor pump and engine. Ensure level is at the center of the sight glass.

2. Drain liquid from the air receiver and moisture trap.

3. Start compressor as per factory instructions. For an easier start, turn the switch on, release pressure from the unloader by pulling the toggle-unloading lever (see Figure 2 on page 4) and start the engine.

4. Check system pressure.

5. Check all pressure relief valves for proper operation.

6. Check control system for proper operation.

Page 9

4. MAINTENANCE

4.1 MAINTENANCE SAFETY

1. Turn off engine and relieve pressure before servicing

2. Open all manual drain valves within the area to be serviced.

3. Isolate the compressor from the compressed air supply by closing a manual shutoff valve upstream and downstream from the compressor. Display a sign in clear view at the shutoff valve stating that the compressor is being serviced.

4. Lock open a pressure relief valve within the pressurized system to allow the system to be completely de-pressurized. NEVER remove a plug to relieve the pressure!

5. Wait for the unit to cool before starting to service. Temperatures of 125 degrees F can burn skin. Some surface temperatures exceed 350 degrees F when the compressor is operating.

4.2 SERVICING INTERVALS

1. Before and / or After Use

a) Check oil levels (engine, pump). b) Drain drop legs and traps in air distribution system. c) Manually operate the pressure relief valves. d) Give compressor an overall visual inspection and be sure safety guards are in place. e) Check for any unusual noise or vibration

f) Check for oil leaks.

2. 50 Hours or Every Two-Weeks Service

a) Inspect the air filter for contamination. Replace the air filter often to ensure a clean air supply to

the compressor pump. b) Clean the cooling surfaces of the intercooler and compressor. c) Check the compressor for air leaks. d) Check the compressed air distribution system for leaks.

e) Inspect oil for contamination. Change more often under humid or dirty conditions.

3. Monthly to Quarterly (160 – 500 hours)

a) Check belt tension and pulley alignment. b) Change oil (more frequently in harsher environments). c) Tighten any loose bolts or sheave fasteners. Check the overall operation of the unit.

4. 6 Months (1000 hours)

a) Inspect compressor valves for leakage and/or carbon build-up.

NOTE: Please read Engine Service/Maintenance Manual for extending service life of the gasoline engine.

Page 10

4.3 LUBRICANT

1. Oil Level

Always operate the unit in a level position. Prior to start-up, check the sight glass to ensure the oil in the pump is at the required level. If the oil level is too low, remove the oil fill plug and add oil until the level is at the center of the sight glass. For approximate oil requirements, see page 14. Do not overfill or under fill as it could damage the pump. CAUTION! The oil level in the pump crankcase

must be checked daily.

2. Oil Type

The correct lubricant is essential to the proper operation of your compressor. For single stage or 2stage compressors, use ISO 68, SAE 25 weight oil. This compressor oil is available at your local Princess Auto store. CAUTION! Do not use motor oil in the compressor pump.

3. Condensation

Water condensing in the crankcase can occur under certain humid conditions or light duty cycling. This water must be removed from the pump to prevent damage. Drain the oil and refill.

Condensation can be prevented by allowing the pump to reach its normal operating temperature by releasing air from the tank and allowing the pump to run, or by using more air, which will cause the pump to operate more frequently. CAUTION! A rise in the oil level and a milky color indicates that condensation is forming in the crankcase. This condensation must be drained immediately or the pump may be damaged.

4.4 PULLEY ALIGNMENT & BELT TENSION

Improper pulley alignment and belt tension are causes for motor overloading, excessive vibration and premature belt or bearing failure. To prevent this from happening, check the pulley alignment and belt tension on a regular basis.

Periodically, inspect both the motor and compressor pulleys for oil, grease, nicks or burrs. Clean or replace pulleys if necessary. Make sure the pulleys are securely fastened. Align the compressor pulley with motor. The drive belt grooves of both pulleys should be in line with each other. The compressor crankshaft must be parallel to the motor shaft.

WARNING! To avoid personal injury, always shut off main power disconnects for the compressor and relieve all air pressure from the system before performing any service on the air compressor.

1. Belt Tension

Proper belt tension and pulley alignment must be maintained for maximum drive efficiency and belt life. The correct tension exists if a deflection (see A in Figure 4 on the next page) of ½” (13 mm) occurs by placing 10 lb (4.4 kg) of force (see B in Figure 4 on the next page) midway between the motor pulley and the pump flywheel. This deflection can be adjusted by the following procedure. The pulley should be carefully aligned with the flywheel and all setscrews should be kept tight.

Page 11

4.4 ADJUSTING PULLEY ALIGNMENT & BELT TENSION (cont’d)

1. Belt Tension (cont’d)

1/2” Deflection

10 Lbs Force

Figure 4: Belt Tension

a) Remove the belt guard. b) Loosen the motor mounting bolts. c) Shift the motor to the point where the correct deflection exists. d) Retighten the motor mounting bolts. e) Check to ensure that the tension remained correct. f) Reinstall the belt guard. All moving parts must be guarded.

2. Pulley Alignment

To check pulley alignment, remove the belt guard and place a straightedge (C in Figure 5 below) against the pump flywheel (D in Figure 5 below). Measure and record the distance from the straightedge to the edge of the drive belt (dimension E). Then measure the distance from the straightedge to the edge of the drive belt again as shown by dimensions F and G. Both distances should be the same as dimension E. If F or G is different from E, there is a misalignment that must be corrected before the compressor is run. To correct a pulley misalignment, use the following procedure.

a) Remove the belt guard. b) Loosen the motor mounting bolts. c) Loosen the setscrew on the motor pulley. d) Align the motor pulley with the pump flywheel (E=F=G). e) Retighten the motor pulley setscrew. f) Adjust the proper belt tension. g) Retighten the motor mounting bolts. h) Reinstall the belt guard. All moving parts must be guarded.

Figure 5: Pulley Alignment

Page 12

5. TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

Compressor Stalls Low gasoline

Bad unloader/check valve Seized pump Low engine idle speed or improper

carburetor setting

Low discharge pressure Air leaks

Restricted air intake Leaking valves Blown gaskets Worn piston rings or cylinder Defective unloader Drive belt slipping Defective pressure gauge

Compressor pump knocking Loose engine pulley or compressor

flywheel Low oil level in pump crankcase Excess carbon on valves on top of

piston Worn connector rod at wrist pin end

Oil in discharge air Worn piston rings or cylinder

Restricted air intake Oil level too high

Overheating Poor ventilation

Dirty cooling surfaces Clogged intake system Inadequate lubrication Restricted air passages Pulley rotation wrong

Excessive belt wear Pulley out of alignment

Improper belt tension Pulley wobbles

Add gasoline. Replace unloader/check valve. Contact authorized service center. Refer to Engine Operator’s Manual. Tighten or replace leaking fittings or connections.

Do not over-tighten. Clean or replace air filter element(s). Contact authorized service centre. Contact authorized service centre. Contact authorized service centre. Contact authorized service centre. Adjust drive belt. Replace gauge.

Tighten pulley and flywheel. Check alignment.

Keep oil level full at all times. Contact authorized service centre.

Contact authorized service centre. Contact authorized service centre.

Clean or replace the air filter element(s). Reduce to proper level. Use non-detergent oil.

Relocate compressor to an area with cool, dry, well circulated air at least 12 in. from the nearest wall.

Clean all cooling surfaces thoroughly. Clean/replace intake filter. Check oil level. Replace transfer tubes and/or unloader. Check pulley rotation direction.

Realign pulley with compressor flywheel. Readjust Replace the pulley and check for a damaged

crankshaft or flywheel.

Page 13

PROBLEM CAUSE SOLUTION

Compressor won’t start in cold temperature

Low pressure (75 psi) pressure relief valve opens High pressure (225 psi) pressure relief valve opens Water in the crankcase Condensation

Excessive vibration Loose pulley

Excessive oil consumption Defective breather valve

Too much back pressure in tank

Discharged battery Compressor too cold

Using wrong grade oil

Intake valve to high pressure cylinder is plugged Unloader/check valve blocked Clean or replace the unloader.

Pump or motor not secured Foundation or frame inadequate

Compressor feet are not level

Wrong grade oil Leaking oil seal Restricted intake

Release pressure from unloader by pulling toggle upwards and start the engine.

Recharge Move compressor to a warmer location.

Use ISO 1001 30W compressor oil in temperatures above 30°F (-1°C) and 10W oil below 30°F (-1°C). Contact authorized service centre.

Change oil. Run compressor for longer period until it is hot, ensuring the discharge valve is open. Tighten pulley.

Tighten bolts. Check mounting. Surface should be level and

strong. Level with shims.

Check breather valve. Use correct grade of compressor oil. Replace oil seal. Check intake system.

Page 14

6. SPECIFICATIONS

Model #

Part #

Tank Capacity

Rated (PSI) CFM

Tank Size

Diameter (in) Height/Length (in) Plate (in)

Pump Model Compression Stage

Cylinder Oil Required (fill to center

of sight glass)

Engine

RPM HP Electric Start Oil Alert

Unloader Battery

Volt (DCV) Battery Capacity (AH) Max Starter Motor Draw

(A)

11G-2-30H

8041212

30 gal 200

18.00 @ 100 PSI

16.00 @ 175 PSI

16.00

38.50

38.50 x 13 x 4.75 LP205CT 2

1.5 L Honda

3600 11 Yes Yes

135-170 PSI Pre-set Optional 12

32 60

9G-2-30H

8120255

30 gal 200

20 @ 100 PSI

17.5 @ 175 PSI

16.00

38.50

38.50 x 13 x 4.75 LP335SK 2

0.86 L Honda

3600 9 No Yes

135-170 PSI Pre-set N/A N/A N/A

9G-1-10TT

8048530

10 gal 200

18.50 @ 100 PSI

16.00 @ 140 PSI

6.00

40.00 28 x 10 x 3

LPW6548ALHI 1

1.6 L Honda

3600 9 No Yes

115-140 PSI Pre-set

6.5G-1-10TT 8120271

10 gal 200

13.5 @ 90 PSI

11.5 @ 125 PSI

6.00

40.00 28 x 10 x 3

LPSS7550 1

0.8 L Ducar

3600

6.5 No Yes

95-125 PSI Pre-set

Page 15

Model #

Part #

Tank Capacity

Rated (PSI) CFM

Tank Size

Diameter (in) Height/Length (in) Plate (in)

Pump Model Compression Stage

Cylinder Oil Required

of sight glass)

Engine

RPM HP Electric Start Oil Alert

Unloader Battery

Volt (DCV) Battery Capacity (AH) Max Starter Motor Draw

(A)

(fill to center

5.5G-1-10TT 8057739

10 gal 200

13.80 @ 40 PSI

11.70 @ 90 PSI

6.00

40.00 28 x 10 x 3

LPV6546ALHI 1

0.9 L Honda

3600

5.5 No Yes

95-125 PSI Pre-set N/A N/A

9G-1-26H

8077513

26 gal 200

18.50 @ 100 PSI

16.00 @ 140 PSI

14.00

36.50 28 x 9 x 3.50

LPW6548ALHI 1

1.6 L Honda

3600 9 No Yes

115-140 Pre-set

Page 16

6.1 TORQUE SPECIFICATIONS

The table shown below gives the correct torque values for various bolts and cap screws. Tighten all bolts to the torque values specified unless otherwise noted. Periodically check the torque values of all fasteners using the table as a guide. Replace hardware with the same strength materials.

Bolt

Diameter (in)

N/m ft-lbs N/m ft-lbs N/m ft-lbs

1/4 8 6 12 9 17 12

5/16 13 10 25 19 36 27

3/8 27 20 45 33 63 45

7/16 41 30 72 53 100 75

1/2 61 45 110 80 155 115

9/16 95 70 155 115 220 165

5/8 128 95 215 160 305 220 3/4 225 165 390 290 540 400 7/8 230 170 570 420 880 650

1 345 225 850 630 1320 970

SAE Grade 2 SAE Grade 5 SAE Grade 8

Page 17

Page 18

7. ASSEMBLY PARTS LIST

COMPRESSOR

11 HP GAS 2 STAGE HORIZONTAL

MODEL #11G – 2 – 30H

ITEM #8041212

Page 19

COMPRESSOR

11 HP GAS 2 STAGE HORIZONTAL

MODEL #11G-2-30H

ITEM #8041212

No. Item No. Description Qty

1 9236118 RELIEF VALVE 200/210 PSI 1 2 10002224 TANK AIR COMPRESSOR 30 GAL 1 3 1292283 TEE B .25 NPTM X .25 NPTF SW 1 4 9236084 GAUGE PRESSURE 0-300 PSI 1 5 0430090 DRAIN COCK BRASS .25 NPT 1 6 9161449 DECAL MAINTENANCE 1 7 10001076 DECAL POWERFIST COMPRESSOR RATING 1 8 9161365 DECAL DRAIN WATER 1

9 9160813 DECAL PAL SERIAL # 1 10 9161290 DECAL CAUTION HANDLING 1 11 9238544 NIPPLE B .500 NPT X 3.0 LG 1 12 9238551 UNLOADER GAS COMPRESSOR C/W 1/8 135-170 1 13 9238569 ELBOW B .50 NPTM X .75 SAE 1 14 9238187 HOSE DISCHARGE .75 OD X 26.00" LG 1 15 9238320 CABLE THROTTLE CONTROL 30" 1 16 9251919 ENGINE 11 HP HONDA ELEC. START 1 17 3850328 PULLEY 2BK34 H 1 18 3851342 BUSHING SPLIT TAPERED 1.000 1 19 10003266 BOLT HEX SER. .375-16 UNC X 1.75 LG 8 20 9161274 DECAL WARNING RISK OF FIRE 1 21 9236183 NUT HEX SER. .375-16 UNC 8 22 10002222 COMPRESSOR HEAD 5HP 2 STG 1 23 3860277 BELT V B66 2 24 9238460 ELBOW .75 NPTM X .75 SAE FLAR 1 25 9316811 ELBOW B .125 NPTM X .25 1 26 9330051 INSERT B COMP .25 X .125 NPTM 2 27 9238478 TUBE RD NYLON .25 OD X 19" LG 1 28 9330721 SLEEVE B COMPRESSION .25 TUBE 1 29 9252305 NIPPLE B .375 NPT X 3.00 LG 1 30 9330077 ELBOW B. .375 NPT STREET 1 31 9236548 CAP B. HEX .375 NPTF 1 32 10000035 BELT GUARD 11 HP 1 33 9235250 BOLT HEX SER. .312-18UNC X .75 LG 4 34 9229691 NUT HEX SERRATED FLANGE .312-18 UNC 4 35 9254426 BRACKET BELT GUARD 5 HP 1 36 9852732 WASHER PTD .344 ID X 1.125 OD X .078 THK 1 37 9803271 BOLT HEX .250-20 UNC X .75 LG 1 38 9161340 DECAL ARROW 1 39 9234410 ELBOW B .25 NPT STREET 90 1 40 10001163 DECAL WARNING GAS AIR COMPRESSORS 1 41 9803297 BOLT HEX .250-20 UNC X 1.00 LG 2 42 9801275 BOLT HEX .375-24 UNF X 1.00 LG 1 43 9852724 WASHER PTD .390 ID X 1.500 OD X .083 THK 1 44 10002560 TAG BREAK-IN OIL 1 45 PLUG DISCHARGE PORT .75 NPTM 1 46 PLUG DISCHARGE PORT 2.0 NPTM 1 47 PLUG DISCHARGE PORT 2.0 NPTM X .75 NPTF 1

Page 20

COMPRESSOR

9 HP GAS 2 STAGE HORIZONTAL

MODEL #9G – 2 – 30H

ITEM #8120255

11 23

4 5

34 36

40 18

Page 21

COMPRESSOR

9 HP GAS 2 STAGE HORIZONTAL

MODEL #9G – 2 – 30H

ITEM #8120255

No. Item No. Description Qty

1 10002469 COMPRESSOR HEAD 2 STG LP335SK 1

2 9233693 ENGINE 9 HP HONDA 1

3 10000035 BELT GUARD 11 HP 1

4 10003071 PULLEY 2BK32H 1

5 3851342 BUSHING SPLIT TAPERED 1.000 1

6 10003003 BRACKET BELT GUARD 9 HP 1

7 9852732 WASHER PTD .344 ID X 1.125 OD X .078 THK 1

8 9803271 BOLT HEX .250-20 UNC X .75 LG 1

9 9803297 BOLT HEX .250-20 UNC X 1.00 LG 2 10 9238544 NIPPLE B .500 NPT X 3.0 LG 1 11 9255969 UNLOADER 135-170 PSI 1 12 9251935 BOLT HEX SER. .375-16UNC X 2.00 LG 8 13 9236183 NUT HEX SER. .375-16 UNC 8 14 1292283 TEE B .25 NPTM X .25 NPTF SW 1 15 9236084 GAUGE PRESSURE 0-300 PSI 1 16 9234410 ELBOW B .25 NPT STREET 90 2 17 9236118 RELIEF VALVE 200/210 PSI 1 18 0430090 DRAIN COCK BRASS .25 NPT 1 19 9235250 BOLT HEX SER. .312-18UNC X .75 LG 4 20 9229691 NUT HEX SERRATED FLANGE .312-18 UNC 4 21 9238320 CABLE THROTTLE CONTROL 30" 1 22 9238569 ELBOW B .50 NPTM X .75 SAE 1 23 9238187 HOSE DISCHARGE .75 OD X 26.00" LG 1 24 9160813 DECAL PAL SERIAL # 1 25 9161274 DECAL WARNING RISK OF FIRE 1 26 10003073 BELT V B61 2 27 1291756 NIPPLE HEX .75 NPT X .75 NPT 1 28 10002560 TAG BREAK-IN OIL 1 29 9330085 ELBOW B. .75 NPTF X .75 SAE FLARE 1 30 9313826 BUSH S .375 NPTM X .250 NPTF 1 31 9237355 NIPPLE B .250 NPT X 2.0 LG 1 32 9253907 CAP HEX B .25 NPTF 1 33 9161449 DECAL MAINTENANCE 1 34 10001076 DECAL POWERFIST COMPRESSOR RATING 1 35 9161290 DECAL CAUTION HANDLING 1 36 9161365 DECAL DRAIN WATER 1 37 9161340 DECAL ARROW 1 38 10001163 DECAL WARNING GAS AIR COMPRESSORS 1 39 PLUG DISCHARGE PORT 2.0 NPTM 1 40 PLUG DISCHARGE PORT 2.0 NPTM X .75 NPTF 1 41 PLUG DISCHARGE PORT .75 NPTM 1 42 10002224 TANK AIR COMPRESSOR 30 GAL 1

Page 22

COMPRESSOR

9 HP GAS 1 STAGE TWIN TANK

MODEL #9G – 1 – 10TT

ITEM #8048530

33832

18 19

Page 23

COMPRESSOR

9 HP GAS 1 STAGE TWIN TANK

MODEL #9G – 1 – 10TT

ITEM #8048530

No. Item No. Description Qty

1 9254004 TANK TWIN 10 GAL 1 2 0430090 DRAIN COCK BRASS .25 NPT 2 3 10002591 TEE B .25 NPTM X .25 NPTF X .25 NPTF 1 4 9160813 DECAL PAL SERIAL # 1 5 9236084 GAUGE PRESSURE 0-300 PSI 1 6 10002414 BELT GUARD TWIN TANK 1 7 9852351 WASHER PTD .281 ID X .625 OD 4 8 9853334 WASHER LOCK SPLIT REG .25 PTD 4

9 9803271 BOLT HEX .250-20 UNC X .75 LG 4 10 10001977 COMPRESSOR HEAD 5 HP 1 STG 3 CYL LPW655 1 11 9229683 BOLT HEX SRD FLANGE .312-18 UNC X 1.50 4 12 9229691 NUT HEX SERRATED FLANGE .312-18 UNC 4 13 9240300 ENGINE 9 HP HONDA OIL ALERT 1 14 9253980 PULLEY 4.75 OD H STYLE 1 15 3851342 BUSHING SPLIT TAPERED 1.000 1 16 9800228 BOLT HEX .250-20 UNC X 1.50 LG 2 17 9161274 DECAL WARNING RISK OF FIRE 1 18 9252750 RUBBER BUMPER FOR .250 BOLT 4 19 9803297 BOLT HEX .250-20 UNC X 1.00 LG 4 20 9226341 NUT HEX SER FLANGE .250-20 UNC 4 21 9253972 UNLOADER COMPRESSOR PRE-SET 115-140 PSI 1 22 1295021 ELBOW .50 JIC X .50 NPTM BRASS 1 23 9253022 AXLE .625 DIA X 5.25 LG 1 24 9860099 COTTER PIN .125 X 1.50 PLATED 2 25 2026342 WHEEL 4.10/3.50-4 X .625 AXLE 1 26 9253030 HAND GRIP FOR .875 OD RD TUBE 2 27 9237355 NIPPLE B .250 NPT X 2.0 LG 1 28 9234410 ELBOW B .25 NPT STREET 90 1 29 9253907 CAP HEX B .25 NPTF 1 30 9803826 BOLT HEX .375-16 UNC X 1.75 LG GR 5 PTD 4 31 9852401 WASHER PTD .438 ID X 1.00 OD X .083 THK 4 32 9853359 WASHER LOCK SPLIT REG .375 PTD 4 33 9856618 NUT HEX .375-16 UNC GR 5 PTD 4 34 9252503 RELIEF VALVE 150/160 PSI PRE-SET 1 35 3860010 BELT V A58 1 36 10000918 HOSE DISCHARGE .50 ID X 14.25" LG 1 37 9238320 CABLE THROTTLE CONTROL 30" 1 38 10001080 DECAL COMPRESSOR RATING 1 39 9161449 DECAL MAINTENANCE 1 40 9161365 DECAL DRAIN WATER 2 41 9161340 DECAL ARROW 1 42 9161290 DECAL CAUTION HANDLING 1 43 10001163 DECAL WARNING GAS AIR COMPRESSORS 1 44 9313826 BUSH S .375 NPTM X .250 NPTF 1 45 10002560 TAG BREAK-IN OIL 1 46 PLUG DISCHARGE PORT .50 NPTM 1

Page 24

COMPRESSOR

6.5 HP GAS 1 STAGE TWIN TANK MODEL #6.5G – 1 – 10TT

30 29 28

ITEM #8120271

2 12

4245

27 31

32 33

Page 25

COMPRESSOR

6.5 HP GAS 1 STAGE TWIN TANK MODEL #6.5G – 1 – 10TT

ITEM #8120271

No. Item No. Description Qty

1 9253006 RELIEF VALVE 135/145 PSI, .25 NPTM 1 2 10002564 PULLEY 4.5 OD A BELT 1 3 9226341 NUT HEX SER FLANGE .250-20 UNC 4 4 9254004 TANK TWIN 10 GAL 1 5 0430090 DRAIN COCK BRASS .25 NPT 2 6 10003075 COMPRESSOR HEAD 1 STG LPSS7550 1 7 9236084 GAUGE PRESSURE 0-300 PSI 1 8 9252982 UNLOADER COMPRESSOR PRE-SET 95-125 PSI 1

9 9252750 RUBBER BUMPER FOR .250 BOLT 4 10 10002591 TEE B .25 NPTM X .25 NPTF X .25 NPTF 1 11 10002753 ENGINE 6.5 HP DUCAR 1 12 3851318 BUSHING SPLIT TAPERED .75 1 13 9234410 ELBOW B .25 NPT STREET 90 1 14 1295021 ELBOW .50 JIC X .50 NPTM BRASS 2 15 9254616 HOSE COMPRESSOR DISCHARGE 1 16 9238320 CABLE THROTTLE CONTROL 30" 1 17 9800228 BOLT HEX .250-20 UNC X 1.50 LG 2 18 9313826 BUSH S .375 NPTM X .250 NPTF 1 19 9803297 BOLT HEX .250-20 UNC X 1.00 LG 4 20 10002560 TAG BREAK-IN OIL 1 21 2026342 WHEEL 4.10/3.50-4 X .625 AXLE 1 22 9860099 COTTER PIN .125 X 1.50 PLATED 2 23 9253022 AXLE .625 DIA X 5.25 LG 1 24 9253030 HAND GRIP FOR .875 OD RD TUBE 2 25 9229683 BOLT HEX SRD FLANGE .312-18 UNC X 1.50 4 26 10002565 BELT V A54 1 27 9229691 NUT HEX SERRATED FLANGE .312-18 UNC 4 28 9852351 WASHER PTD .281 ID X .625 OD 4 29 9853334 WASHER LOCK SPLIT REG .25 PTD 4 30 9803271 BOLT HEX .250-20 UNC X .75 LG 4 31 9856600 NUT HEX .312-18 UNC GR 5 PTD 4 32 9852369 WASHER PTD .312 ID X .734 OD 4 33 9853342 WASHER LOCK SPLIT REG .312 PTD 4 34 9803578 BOLT HEX .312-18 UNC X 1.75 LG 4 35 9253907 CAP HEX B .25 NPTF 1 36 10002414 BELT GUARD TWIN TANK 1 37 9237355 NIPPLE B .250 NPT X 2.0 LG 1 38 9161274 DECAL WARNING RISK OF FIRE 1 39 9161449 DECAL MAINTENANCE 1 40 9161340 DECAL ARROW 1 41 9161365 DECAL DRAIN WATER 2 42 9161290 DECAL CAUTION HANDLING 1 43 10001163 DECAL WARNING GAS AIR COMPRESSORS 1 44 9160813 DECAL PAL SERIAL # 1 45 10001079 DECAL COMPRESSOR RATING 1 46 PLUG DISCHARGE PORT .50 NPTM 1

Page 26

COMPRESSOR

5.5 HP GAS 1 STAGE TWIN TANK MODEL #5.5G – 1 – 10TT

ITEM #8057739

34 35 36

5 3

Page 27

COMPRESSOR

5.5 HP GAS 1 STAGE TWIN TANK MODEL #5.5G – 1 – 10TT

ITEM #8057739

No. Item No. Description Qty

1 9254004 TANK TWIN 10 GAL 1 2 0430090 DRAIN COCK BRASS .25 NPT 2 3 10002591 TEE B .25 NPTM X .25 NPTF X .25 NPTF 1 4 9236084 GAUGE PRESSURE 0-300 PSI 1 5 9253006 RELIEF VALVE 135/145 PSI, .25 NPTM 1 6 9252982 UNLOADER COMPRESSOR PRE-SET 95-125 PSI 1 7 9252750 RUBBER BUMPER FOR .250 BOLT 4 8 9803297 BOLT HEX .250-20 UNC X 1.00 LG 4

9 9226341 NUT HEX SER FLANGE .250-20 UNC 4 10 9253022 AXLE .625 DIA X 5.25 LG 1 11 9860099 COTTER PIN .125 X 1.50 PLATED 2 12 9253030 HAND GRIP FOR .875 OD RD TUBE 2 13 2026342 WHEEL 4.10/3.50-4 X .625 AXLE 1 14 10002414 BELT GUARD TWIN TANK 1 15 10002335 COMPRESSOR HEAD 3 HP 1 STAGE 2CYL 1 16 10002593 NIPPLE B. .25 NPT X 4.00 LG 1 17 9253907 CAP HEX B .25 NPTF 1 18 9212135 ENGINE 5.5 HP HONDA OIL ALERT 1 19 10002565 BELT V A54 1 20 10002564 PULLEY 4.5 OD A BELT 1 21 3851318 BUSHING SPLIT TAPERED .75 1 22 1295021 ELBOW .50 JIC X .50 NPTM BRASS 1 23 10000918 HOSE DISCHARGE .50 ID X 14.25" LG 1 24 9238320 CABLE THROTTLE CONTROL 30" 1 25 9160813 DECAL PAL SERIAL # 1 26 9161274 DECAL WARNING RISK OF FIRE 1 27 10001079 DECAL COMPRESSOR RATING 1 28 9161449 DECAL MAINTENANCE 1 29 9161290 DECAL CAUTION HANDLING 1 30 10001163 DECAL WARNING GAS AIR COMPRESSORS 1 31 9161365 DECAL DRAIN WATER 2 32 9161340 DECAL ARROW 1 33 9800228 BOLT HEX .250-20 UNC X 1.50 LG 2 34 9852351 WASHER PTD .281 ID X .625 OD 4 35 9853334 WASHER LOCK SPLIT REG .25 PTD 4 36 9803271 BOLT HEX .250-20 UNC X .75 LG 4 37 9803578 BOLT HEX .312-18 UNC X 1.75 LG 4 38 9852369 WASHER PTD .312 ID X .734 OD 4 39 9853342 WASHER LOCK SPLIT REG .312 PTD 4 40 9856600 NUT HEX .312-18 UNC GR 5 PTD 4 41 9229683 BOLT HEX SRD FLANGE .312-18 UNC X 1.50 4 42 9229691 NUT HEX SERRATED FLANGE .312-18 UNC 4 43 10002560 TAG BREAK-IN OIL 1 44 9234410 ELBOW B .25 NPT STREET 90 1 45 PLUG DISCHARGE PORT .50 NPTM 1

Page 28

COMPRESSOR

9 HP GAS 2 STAGE HORIZONTAL

MODEL #9G – 1 – 26H

ITEM #8077513

243625

Page 29

COMPRESSOR

9 HP GAS 26 GAL HORZ PORTABLE

MODEL #9G – 1 – 26H

ITEM #8077513

No. Item No. Description Qty

1 10001162 TANK AIR 26 GAL PORTABLE 1 2 10001977 COMPRESSOR HEAD 5 HP 1 STG 3 CYL LPW655 1 3 9253162 BLOCK FIVE WAY 1 4 1291715 NIPPLE HEX .375 NPTM 1 5 9225681 VALVE .375 NPTF B BODY SS BALL 1 6 9236084 GAUGE PRESSURE 0-300 PSI 1 7 9252503 RELIEF VALVE 150/160 PSI PRE-SET 1 8 9315532 NIPPLE HEX S .500 NPT 1

9 1291616 PLUG HEX CI .375 NPTM 1 10 0430090 DRAIN COCK BRASS .25 NPT 1 11 9160813 DECAL PAL SERIAL # 1 12 9229683 BOLT HEX SRD FLANGE .312-18 UNC X 1.50 4 13 9229691 NUT HEX SERRATED FLANGE .312-18 UNC 4 14 9252750 RUBBER BUMPER FOR .250 BOLT 2 15 9803297 BOLT HEX .250-20 UNC X 1.00 LG 2 16 9226341 NUT HEX SER FLANGE .250-20 UNC 2 17 10002242 ELBOW S .50 NPTM X .50 NPTF SW 90 DEG 1 18 9253972 UNLOADER COMPRESSOR PRE-SET 115-140 PSI 1 19 9240300 ENGINE 9 HP HONDA OIL ALERT 1 20 9253980 PULLEY 4.75 OD H STYLE 1 21 3851342 BUSHING SPLIT TAPERED 1.00" 1 22 3860010 BELT V A58 1 23 9803826 BOLT HEX .375-16 UNC X 1.75 LG GR 5 PTD 4 24 9852682 WASHER PTD .390 ID X .125 THK 4 25 9853359 WASHER LOCK SPLIT REG .375 PTD 4 26 9856618 NUT HEX .375-16 UNC GR 5 PTD 4 27 9253030 HAND GRIP FOR .875 OD RD TUBE 2 28 9314824 NIPPLE HEX S .25 X .25 1 29 9234410 ELBOW B .25 NPT STREET 90 2 30 9253907 CAP HEX B .25 NPTF 1 31 2020060 WHEEL 4.10/3.50-4 X .625 AXLE 2 32 10002046 BOLT SHOULDER .500-13 UNC X .625 DIA 2 33 9857574 NUT LOCK UNITORQ .500-13 UNC 2 34 10002414 BELT GUARD TWIN TANK 1 35 9852351 WASHER PTD .281 ID X .625 OD 4 36 9853334 WASHER LOCK SPLIT REG .25 PTD 4 37 9803271 BOLT HEX .250-20 UNC X .75 LG 4 38 1295021 ELBOW .50 JIC X .50 NPTM BRASS 1 39 9254616 HOSE COMPRESSOR DISCHARGE 1 40 9238320 CABLE THROTTLE CONTROL 30" 1 41 10001677 DECAL POWERFIST COMPRESSOR RATING 1 42 9161449 DECAL MAINTENANCE 1 43 9161365 DECAL DRAIN WATER 1 44 10001163 DECAL WARNING GAS AIR COMPRESSORS 1 45 9161274 DECAL - WARNING REFUEL 1 46 9161340 DECAL ARROW 1 47 9800228 BOLT HEX .250-20 UNC X 1.50 LG 2 48 10002560 TAG BREAK-IN OIL 1 49 9313826 BUSH S .375 NPTM X .250 NPTF 1

Page 30