POWEREX PP200B120 Datasheet
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
TENTATIVE
Description:
The Powerex POW-R-PAK
based power assembly that may be used as a
converter, chopper, half or full bridge, or three phase
inverter for motor control, power supply, UPS or other
power conversion applications.
The power assembly is mounted on a forced aircooled heatsink and features state-of-the-art Powerex
F-series trench gate IGBTs with low conduction and
switching losses for high efficiency operation. The
POW-R-PAK
TM
includes a low inductance laminated
bus structure, optically isolated gate drive interfaces,
isolated gate drive power supplies, and a DC-link
capacitor bank. The control board provides a
simple user interface along with built-in
protection features including overvoltage,
undervoltage lockout, overcurrent,
overtemperature, and short circuit detection.
Depending on application characteristics the
POW-R-PAK
TM
is suitable for operation with DC
bus voltages up to 800VDC and switching
frequencies above 20kHz.
Schematic
TM
is a configurable IGBT
Features:
High performance IGBT inverter bridge
Integrated gate drive with fault monitoring
& protection
System status / troubleshooting LEDs to
verify or monitor proper operation
Isolated gate drive power supplies
Low inductance laminated bus
Output current measurement & feedback
Superior short circuit detection & shoot
through prevention
PP200B120
POW-R-PAK
200A / 1200V
H-Bridge IGBT Assembly
TM
PP200B120(-) - 1 -
TENTATIVE
Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
PP200B120
POW-R-PAK
TM
200A / 1200V
H-Bridge IGBT Assembly
Absolute Maximum Ratings, Tj = 25°C unless otherwise specified
General Symbol Units
IGBT Junction Temperature T
Storage Temperature T
Operating Temperature T
Voltage Applied to DC terminals V
Isolation Voltage, AC 1 minute, 60Hz sinusoidal V
IGBT Inverter
Collector Current (TC = 25°C) I
Peak Collector Current (Tj < 150°C) I
Emitter Current I
Peak Emitter Current I
Maximum Collector Dissipation (Tj < 150°C) P
Gate Drive Board
j
stg
op
CC
iso
C
CM
E
EM
c
Unregulated +24V Power Supply 30 Volts
Regulated +15V Power Supply 18 Volts
PWM Signal Input Voltage 20 Volts
Fault Output Supply Voltage 30 Volts
Fault Output Current 50 mA
-40 to +150 °C
-40 to +125 °C
-25 to +85 °C
800 Volts
2500 Volts
200 Amperes
400 Amperes
200 Amperes
400 Amperes
890 Watts
IGBT Inverter Electrical Characteristics, Tj = 25°C unless otherwise specified
Characteristics Symbol Test Conditions Min Typ Max Units
Collector Cutoff Current I
Collector – Emitter Saturation Voltage V
Emitter – Collector Voltage V
Inductive Load Switching Times
CES
CE(sat)
EC
t
d(on)
tr - - 80 ns
t
d(off)
t
Diode Reverse Recovery Time t
rr
Diode Reverse Recovery Charge Q
DC Link Capacitance 4950 µF
VCE = V
, VGE = 0V - - 1 mA
CES
IC = 200A, Tj = 25°C - 1.8 2.4 Volts
IC = 200A, Tj = 125°C - 1.9 - Volts
IE = 200A - - 3.2 Volts
- - 300 ns
VCC = 600V
= 200A
I
C
V
= 15V
f
rr
GE
= 1.6Ω
R
G
- - 500 ns
- - 300 ns
- - 200 ns
- 12.2 - µC
PP200B120(-) - 2 -
Loading...